Information/Service; Reset To Factory Settings; Data Clear; Password - Mitsubishi Electric DX-TL2500E Installation And Operation Manual

<RESET TO FACTORY SETTINGS>
>>EXECUTE
SHUTTLE>>:EXECUTE,<<:CANCEL
2. Turn the SHUTTLE ring clockwise.
• The menu screen settings are reset.
3. Turn the SHUTTLE ring counterclockwise or press the SET
UP button.

DATA CLEAR

For deleting data in MAIN HDD, SUB HDD, LPA HDD,
CFC (Compact Flash Card), or ARCHIVE/COPY device.
"SUB HDD DATA CLEAR" is appeared when the
"HDD SETTING" is selected on "PARTITION" ("LONG
PRE-ALARM") of the <INITIALIZATION> screen.
"LPA HDD DATA CLEAR" is appeared when the
"HDD SETTING" is selected on "LONG PRE-ALARM"
of the <INITIALIZATION> screen after installing EX-
TRA HDD to "INTERNAL HDD A".
"ARCHIVE DATA CLEAR" and "COPY DATA
CLEAR" are appeared when "ARCHIVE•COPY" is se-
lected on "ID4•ID5" of the <INITIALIZATION> screen.
Performing "MAIN HDD DATA CLEAR" while in
"MIRRORING" mode deletes all data.
1. Press the SET UP button } <SETTINGS> } <INITIAL
SET UP/INFORMATION> } Select the desired item to clear
in the <INFORMATION/SERVICE> screen. Turn the
SHUTTLE ring clockwise.
• "PUSH WARNING RESET KEY FOR 1 SECOND TO CLEAR"
appears on the bottom of the screen.
• To cancel the deletion, turn the SHUTTLE ring counter-
clockwise.
<MAIN HDD DATA CLEAR>
PUSH WARNING RESET KEY
FOR 1 SECOND TO CLEAR
When a password for level 4 has been registered
and locked, and the settings for "MAIN HDD DATA
CLEAR", "SUB HDD DATA CLEAR", and "LPA HDD
DATA CLEAR" are made, the <UNLOCK PASSWORD>
screen will be displayed and the lock must be unlocked.
2. Press the WARNING RESET button for 1 second.
• "CLEARING ..." appears on the screen.
Data cannot be erased when accessing to HDD as
playing/recording/copying/restoring.
3. Turn the SHUTTLE ring counterclockwise or press the SET
UP button.
•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Operations

PASSWORD

The unit is equipped with 2 lock functions : SIMPLE
LOCK that does not require the PASSWORD when un-
locking and PASSWORD LOCK that require the PASS-
WORD when unlocking.
• If the PASSWORD for unlocking has not been set :
Lock function will be SIMPLE LOCK
• If the PASSWORD for unlocking has been set : Lock
function will be PASSWORD LOCK.
When the MAIN switch on the rear of the unit is set
to ON, SIMPLE LOCK/PASSWORD LOCK setting can
be made even with the POWER button on the front set
to OFF.
When the MAIN switch on the rear of the unit is set
to OFF or when a menu is being displayed, SIMPLE
LOCK/PASSWORD LOCK will not function.

SIMPLE LOCK

When SIMPLE LOCK is on, buttons other than the
SPLIT/SEQUENCE button, ZOOM button, camera
number buttons 1 ~ 16 and the MAIN switch become
inoperable and the unit will be locked in the current state.
To apply simple lock • • •
1. Press the LOCK button using a ballpoint pen, etc., when
the MAIN switch is set to ON.
• The lock turns on and the LOCK indicator lights.
To unlock simple lock • • •
1. Press the LOCK button.
• The lock is unlocked and the LOCK indicator turns off.

PASSWORD LOCK

PASSWORD LOCK is divided into the two types of "OP-
ERATION CONTROL" and "HDD DATA CLEAR". "OP-
ERATION CONTROL" can be locked in three levels by
operation functions. "HDD DATA CLEAR" makes it possi-
ble to lock the settings "MAIN HDD DATA CLEAR", "SUB
HDD DATA CLEAR", and "LPA HDD DATA CLEAR".
<About PASSWORD LOCK for OPERATION CON-
TROL (level 1 to 3)>
1) Input the PASSWORD of level 1 to 3.
2) Set the PASSWORD LOCK.
• The PASSWORD LOCK of level 1 will be active.
When The PASSWORD LOCK of level 1 is active,
functions of all operations can be locked.
3) Unlock the PASSWORD LOCK of level 1.
• The PASSWORD LOCK of level 2 will be active.
When The PASSWORD LOCK of level 2 is active,
only the SPLIT/SEQUENCE button, ZOOM button,
camera number buttons, OUTPUT A button and OUT-
PUT B button are operable.
4) Unlock the PASSWORD LOCK of level 2.
• The PASSWORD LOCK of level 3 will be active.
59