Yamaha RX-V750 Owner's Manual page 64

IFPlllJff_Ir
i! !! !
Use to adjust the optional system parameters.
n UFi'Ui'i i'Ci"iU'//,
A) Di £;F'LI:I', SE'/
F.,)I,IENOR'? GUARD
C: ? F'AR@i,, iJqI
D)ZOHE SET
[ _] / [ _] I UP/Down
[ SELECT ] _En±er ¸¸
OSD shift 0!!!;[) :!!!;i i]]FT
Use to adjust the vertical position of the OSD.
Choices: +5 (downward) to -5 (upward)
• Press + to lower the position of the OSD.
• Press to raise the position of the OSD.
Gray back (!!iRA",'E:I:::I::K
Selecting AUTO for the on-screen display setting displays
a gray background when there's no video signal input.
Nothing is displayed if OFF is selected.
Choices: AUTO, OFF
• Display set ,-,,r, r,:::i:::,i ,,,, ,::i:::r
'A' i'°,1'I _=,,,' ,=L i
DIHHER ......... iI
U CCIIqU ........ 01£
Oq[,, SHIFT ..... '_
6RF# IF, El::=, =FlUTO
CHF'NT O::.D..... OH
[+] 'iv] I UF Douh
E : ] ::3 ;sELECT
Dimmer i% T MMi:::i:::,
Use to adjust the brightness of the front panel display.
Choices:
-4 to 0
Video conversion i i ,=','%,iii
Use this feature to turn on/off conversion of composite
(VIDEO) signals to both S-Video and component signals.
This allows you to output converted video signals from the
S VIDEO or COMPONENT VIDEO.jacks when no
S-Video or component signals are input. This feature also
converts S-Video signals to component signals when no
component signals are input.
Choices: ON, OFF
• Select OFF not to convert any signals.
• Select ON to convert composite signals to S-Video and
component signals, and to convert S-Video signals to
component signals.
) \ ) (r
• C( n 'el'ted vide_ sienals are only output to Ihe MONITOR OUT
jacks. When recording you must make Ihe same lype ol video
connections (i.e., S-Video) belween each component.
• When converting composite video or S-Video signals from a
VCR to component video signals, the picture qualily may sutTer
depending on your VCR.
If "(;RAY BACK" is set to OFF. no information will be displayed
on the screen when video signals are not being input.
Component OSD C:MF:qqT 0%,
Use this feature to turn on/off OSD output to the
COMPONENT VIDEO MONITOR OUT .jacks when
using the SET MENU, test tone or parameter functions.
Choices: ON, OFF
• Select ON to output the OSD signals from
COMPONENT VIDEO MONITOR OUT .jacks.
• Select OFF if you do not w,ant to output the OSD
signals from COMPONENT VIDEO MONITOR OUT
.jacks.
Set menu lunctions even when OFF is selected.
• Memory guard I!!!OMI!![M(:)F;?."? (!!iUI:::IRI,')
Use this feature to prevent accidental changes to DSP
program parameter values and other system settings.
Choices: OFF, ON
1 ,i i_ u i_,,
UiiiLi iJi'd
}OFF 314
[ (: ] [ : ] I 2;e1e,:t
[:£;ELEC:'/] Re{u_ n
Select ON to protect:
• DSP program parameters
• All SET MENU items
• All speaker levels
• The on-screen display (OSD) mode
When "MEMORY GUARD" is set to ON, you cannot use the lest
lone or select any other SET MENU items.
6O