National Instruments cFP-22 Series Manual

Intelligent real-time controllers for compact fieldpoint

Hide thumbs Also See for cFP-22 Series:

Instructions and specifications (38 pages)

Table of Contents

Quick Links

Download this manual

FIELDPOINT OPERATING INSTRUCTIONS AND SPECIFICATIONS

cFP-2200/2210/2220/2220A

Intelligent Real-Time Controllers for Compact FieldPoint

1 RS-232 Serial Port

2 RJ-45 Ethernet Port 1

3 Removable Compact Flash (cFP-2220 and

cFP-2220A Only)

4 Status LED

5 Power LED

6 User-Configurable LEDs

7 DIP Switches

8 USB Port (cFP-2220 Only)

Front

9 RJ-45 Ethernet Port 2 (cFP-2220 and

10 Reset Button

11 Power Connector

12 Digital Input/Output Terminals (cFP-2220 and

13 RS-485 Serial Port (cFP-2220 and cFP-2220A Only)

14 RS-232 Serial Port (cFP-2220 and cFP-2220A Only)

15 RS-232 Serial Port (cFP-2210, cFP-2220, and

Figure 1. cFP-22xx, Front and Bottom Views

Bottom

cFP-2220A Only)

Table of Contents

Need help?

Do you have a question about the cFP-22 Series and is the answer not in the manual?

Questions and answers

Summary of Contents for National Instruments cFP-22 Series

Page 1 FIELDPOINT OPERATING INSTRUCTIONS AND SPECIFICATIONS cFP-2200/2210/2220/2220A Intelligent Real-Time Controllers for Compact FieldPoint Bottom Bottom Front 1 RS-232 Serial Port 9 RJ-45 Ethernet Port 2 (cFP-2220 and 2 RJ-45 Ethernet Port 1 cFP-2220A Only) 3 Removable Compact Flash (cFP-2220 and 10 Reset Button cFP-2220A Only) 11 Power Connector 4 Status LED...
Page 2: Safety Guidelines For Hazardous Locations
This document describes how to mount the cFP-2200/2210/2220/2220A controllers, how to connect the controllers to networks, and how to use the features of the controllers. This document also contains specifications for the controllers. In this document, the cFP-2200/2210/2220/2220A controllers are referred to inclusively as the cFP-22xx. Safety Guidelines Operate the cFP-22xx only as described in these operating instructions.
Page 3 Each set of mounting instructions in this document includes an instruction to connect the protective earth (PE) ground terminal on the cFP-BP-x backplane to the system safety ground. The backplane PE ground terminal © National Instruments Corporation cFP-2200/2210/2220/2220A...
Page 4 has the following symbol stamped beside it: . Connect the backplane PE ground terminal to safety ground using 14 AWG (1.6 mm) wire with a ring lug. Use the 5/16 in. panhead screw shipped with the backplane to secure the ring lug to the backplane PE ground terminal. To ensure maximum cooling efficiency, mount the Compact FieldPoint so that the I/O module vents are at the top and bottom, as shown in the following figure:...
Page 5 Figure 3. cFP-22xx Installed on cFP-BP-x, Bottom View with Dimensions 4 slots = 246 mm (9.68 in.) 8 slots = 441 mm (17.4 in.) Cabling Clearance Cooling Outline 51 mm (2 in.) All Around Figure 4. cFP-22xx Installed on cFP-BP-4, Front View with Dimensions © National Instruments Corporation cFP-2200/2210/2220/2220A...
Page 6 104.78 mm (4.1 in.) 63.50 mm 127.00 mm (2.5 in.) (5.0 in.) 22.23 mm (0.9 in.) 440.94 mm (17.4 in.) Figure 5. cFP-BP-8, Back View with Dimensions 104.74 mm (4.1 in.) 63.46 mm 127.00 mm (2.5 in.) (5.0 in.) 22.19 mm (0.9 in.) 245.87 mm (9.6 in.)
Page 7 2 DIN Rail Spring 3 DIN Rail Figure 8. One Edge of DIN Rail Inserted in Clip Press down firmly on the backplane to compress the spring until the clip locks in place on the DIN rail. © National Instruments Corporation cFP-2200/2210/2220/2220A...
Page 8 Connect the PE ground terminal on the backplane to safety ground. Caution Disconnect power and make sure that no I/O modules are in the backplane before removing it from the DIN rail. Mounting the Backplane on a Panel The horizontal panel-mount kit has mounting holes on the sides of the backplane and is NI part number 778616-01.
Page 9 102 mm (4 in.) 457 mm (18 in.) Figure 11. cFP-BP-8 with Horizontal Panel-Mount Kit Installed, Front View with Dimensions T I O I N S Figure 12. Installing the Vertical Panel-Mount Kit on the cFP-BP-4 © National Instruments Corporation cFP-2200/2210/2220/2220A...
Page 10 34.0 mm (1.34 in.) 178 mm (7.0 in.) 7.6 mm (0.30 in.) 246 mm (9.7 in.) 17.8 mm (0.70 in.) Figure 13. cFP-BP-4 with Vertical Panel-Mount Kit Installed, Front View with Dimensions 33.1 mm (1.31 in.) 374 mm (14.7 in.) 7.6 mm (0.30 in.) 17.8 mm...
Page 11 (0.090 in.) Figure 15. Dimensions of Rack-Mount Kit Complete the following steps to mount the system in a rack. Fasten the rack-mount bracket to the back of the cFP-BP-x using the captive screws on the bracket. © National Instruments Corporation cFP-2200/2210/2220/2220A...
Page 12 T IO IN S Figure 16. Installing the Rack-Mount Bracket on the cFP-BP-4 T IO IN S Figure 17. Installing the Rack-Mount Bracket on the cFP-BP-8 cFP-2200/2210/2220/2220A ni.com...
Page 13 DIN rail space, you can install an 18 in. rail in a second rack-mount kit using four #10-32 screws. 1 cFP-BP-4 Backplane 3 8 in. DIN Rail 2 Captive #10-32 Nuts 4 #10-32 Screws, 3/8–1/2 in. Figure 18. Installing an 8 in. DIN Rail in the Rack-Mount Kit © National Instruments Corporation cFP-2200/2210/2220/2220A...
Page 14 Installing the cFP-22xx on the Backplane Make sure that no power is connected to the controller. Make sure that the controller is right side up with the NI logo at the top, and align the captive screws on the controller with the holes on the backplane.
Page 15 (2.5 in.) length, tighten the captive screws to 1.1 N · m (10 lb · in.) of torque. Repeat this procedure to install additional I/O modules on the backplane. Figure 20. Installing an I/O Module on the Backplane © National Instruments Corporation cFP-2200/2210/2220/2220A...
Page 16 Installing Connector Blocks on the Backplane In order to connect I/O modules to input signals or loads, you need to install a cFP-CB-x connector block or other connectibility accessory for each I/O module on the backplane. Use the connector socket to the right of each I/O module socket.
Page 17 To prevent data loss and to maintain the integrity of your Ethernet installation, do not use a cable longer than 100 m. If you are using 100 Mbps Ethernet, National Instruments recommends using a CAT-5 or better shielded twisted-pair Ethernet cable. © National Instruments Corporation cFP-2200/2210/2220/2220A...
Page 18 If you need to build your own cable, refer to the Cabling section for more information about Ethernet cable wiring connections. The host computer communicates with the controller over a standard Ethernet connection. If the host computer is on a network, you must configure the controller on the same subnet as the host computer.
Page 19 Figure 22. Wrapping the Power Wires around the Ferrite Figure 23. Closed Ferrite Install a tie wrap or other device on the power wires to secure the ferrite in place near the controller power connector, as shown in Figure 24. © National Instruments Corporation cFP-2200/2210/2220/2220A...
Page 20 Figure 24. Ferrite Installed with Tie Wrap Connect the positive lead of the power supply to the V1 terminal of the COMBICON connector shipped with the cFP-22xx. Connect the negative lead of the power supply to one of the C terminals of the COMBICON connector.
Page 21 COM 1 is an RS-232 DTE serial port with a standard DB-9 connector. The Serial VIs access COM 1 as port 0. The following figure shows the locations of the DB-9 connector pins and Table 1 lists the signals on the pins. © National Instruments Corporation cFP-2200/2210/2220/2220A...
Page 22 Pin 5 Pin 9 Pin 6 Pin 1 Figure 25. Controller Serial Port Table 1. DB-9 Pin Descriptions Signal COM 2 (cFP-2210, cFP-2220, and cFP-2220A Only) COM 2 is an RS-232 DTE serial port with a 10-position modular jack. The Serial VIs access COM 2 as port 1.
Page 23 Only two FP-1001 banks are shown, but the cFP-2220/2220A can control up to 24 FP-1001 banks. Install 120 Ω termination resistors at each end of the network as shown in Figure 27. © National Instruments Corporation cFP-2200/2210/2220/2220A...
Page 24 cFP-2220 COM 4 FP-1001 FP-1001 RXD– RXD+ TXD– TXD+ RX– TX– RX– TX– 120 Ω 120 Ω 120 Ω 120 Ω Figure 27. Wiring for an RS-485 Network Controlled by the cFP-2220/2220A COM 4 is designed to operate in four-wire mode as shown in Figure 27. You can use COM 4 in two-wire mode, but you must design your application so that it filters out the writes that echo back over the read channels.
Page 25: Using The Internal Real-Time Clock
This synchronization provides timestamp data to the controller. You can also use the internal real-time clock to correct drift of the system clock. Please contact National Instruments for more information. © National Instruments Corporation cFP-2200/2210/2220/2220A...
Page 26: Configuring Dip Switches
USER1 Figure 29. DIP Switches All of the DIP switches are in the OFF position when the controller is shipped from National Instruments. IP RESET Switch Push the IP RESET switch to the ON position and reboot the controller to reset the IP address to .
Page 27 VI in a LabVIEW RT embedded VI. You can use the FieldPoint ReadVI to read defined switches in embedded or unembedded applications. For more information about the RT Read Switch VI and the FieldPoint Read VI, refer to the LabVIEW Help. © National Instruments Corporation cFP-2200/2210/2220/2220A...
Page 28: Using The Reset Button
This usually occurs when the controller runs out of memory. Review your RT VI and check the memory usage. Modify the VI as necessary to solve the memory usage issue. Solid The controller has detected an unrecoverable error. Please contact National Instruments. cFP-2200/2210/2220/2220A ni.com...
Page 29 Enterprise Connectivity Toolset. Refer to for more information ni.com about the LabVIEW Enterprise Connectivity Toolset. Note Contact NI to determine whether the version of the toolkit you are using can be downloaded onto the cFP-22xx. © National Instruments Corporation cFP-2200/2210/2220/2220A...
Page 30: Troubleshooting
Remote Front Panels You may need to monitor and control an embedded VI remotely. The cFP-22xx supports multiple remote front panels for embedded VIs. Users can view the remote front panel using either LabVIEW or a Web browser. Users accessing the remote front panels with a Web browser need to have either Internet Explorer 5.5 Service Pack 2 or later, or Netscape 4.7 or later.
Page 31 Right-click the FieldPoint bank and select Format Disk. After formatting, you must reconfigure network settings and reinstall software. Remember to install LabVIEW Real-Time 8.5.1 or later on the controller, because previous versions do not work with the controller. © National Instruments Corporation cFP-2200/2210/2220/2220A...
Page 32: Specifications
Specifications The following specifications are typical for the –40 to 70 °C operating temperature range unless otherwise noted. Network Network interface ........10BaseT and 100BaseTX Ethernet Compatibility ..........IEEE 802.3 Communication rates ......10 Mbps, 100 Mbps, auto-negotiated Maximum cabling distance.....100 m/segment Memory cFP-2200..........128 MB nonvolatile;...
Page 33: Power Requirements
If you need to clean the controller, wipe it with a dry towel. Screw-terminal wiring......Use copper conductor wire with 10 mm (0.39 in.) of insulation from the ends. External digital I/O terminals ..16 to 28 AWG Power supply terminals....14 to 30 AWG © National Instruments Corporation cFP-2200/2210/2220/2220A...
Page 34: Safety Voltages
Torque for screw terminals.....0.5 to 0.6 N · m (4.4 to 5.3 lb · in.) Weight ............278 g (9.8 oz) Safety Voltages Connect only voltages that are within these limits. V terminal to C terminal ......35 V max, Measurement Category I Measurement Category I is for measurements performed on circuits not directly connected to the electrical distribution system referred to as MAINS voltage.
Page 35: Environmental Management
Waste Electrical and Electronic Equipment (WEEE) EU Customers At the end of their life cycle, all products must be sent to a WEEE recycling center. For more information about WEEE recycling centers and National Instruments WEEE initiatives, visit ni.com/environment/weee.htm RoHS...
Page 36: Hazardous Locations
Hazardous Locations U.S. (UL) ..........Class I, Division 2, Groups A, B, C, D, T4; Class I, Zone 2, AEx nL IIC T4 Canada (C-UL) ........Class I, Division 2, Groups A, B, C, D, T4; Class I, Zone 2, Ex nL IIC T4 Europe (DEMKO) cFP-2200/2210/2220A only ....Ex nL IIC T4 Environmental...
Page 37 Connector 1 Connector 2 Pin 1 Pin 8 Pin 1 Pin 8 Figure 31. Ethernet Connector Pinout © National Instruments Corporation cFP-2200/2210/2220/2220A...
Page 38: Where To Go For Support
Where to Go for Support The National Instruments Web site is your complete resource for technical support. At you have access to everything from ni.com/support troubleshooting and application development self-help resources to email and phone assistance from NI Application Engineers.
Page 40 Instruments trademarks. Other product and company names mentioned herein are trademarks or trade names of their respective companies. For patents covering National Instruments products, refer to the appropriate location: Help»Patents in your software, the patents.txt file on your CD, or ni.com/patents.

This manual is also suitable for:

Cfp-2200 Cfp-2210 Cfp-2220 Cfp-2220a

National Instruments cFP-22 Series Manual

Quick Links

Need help?

Questions and answers

Related Manuals for National Instruments cFP-22 Series

Summary of Contents for National Instruments cFP-22 Series

This manual is also suitable for:

Table of Contents