Toro 41621 Operator's Manual

Pivoting hose reel kit 2015 and after multi-pro 5800 turf sprayer

Advertisement

Quick Links

Pivoting Hose Reel Kit
2015 and After Multi-Pro 5800 Turf Sprayer
Model No. 41621—Serial No. 316000001 and Up
Introduction
Read this manual carefully to learn how to operate
and maintain your product properly. The information
in this manual can help you and others avoid injury
and product damage. Although Toro designs and
produces safe products, you are responsible for
operating the product properly and safely.
You may contact Toro directly at www.Toro.com
for product safety and operation training materials,
accessory information, help finding a dealer, or to
register your product.
Whenever you need service, genuine Toro parts, or
additional information, contact an Authorized Service
Dealer or Toro Customer Service and have the model
and serial numbers of your product ready.
illustrates the location of the model and serial numbers
on the product.
1. Model and serial number plate
Model No.
Serial No.
© 2018—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Figure 1
Figure 1
Register at www.Toro.com.
Proposition 65 Warning
This product contains a chemical
or chemicals known to the State of
California to cause cancer, birth defects,
or reproductive harm.
Use of this product may cause exposure
to chemicals known to the State of
California to cause cancer, birth defects,
or other reproductive harm.
Note:
This product complies with all relevant
European directives. For details, please see the
Declaration of Incorporation (DOI) at the back of this
publication.
Determine the left and right sides of the machine from
the normal operating position.
Safety
Improper use or maintenance by the operator or
owner can result in injury. To reduce the potential
for injury, comply with these safety instructions
g028037
and always pay attention to the safety-alert
symbol, which means Caution, Warning, or
Danger—personal safety instruction. Failure to
comply with the instruction may result in personal
injury or death.
Read also the safety and operation instructions in the
vehicle Operator's Manual.
Do not aim the hand sprayer at any person or
animal. Fluids under high pressure can penetrate
skin and cause severe injury, possibly resulting in
amputation or death. Hot liquids and chemicals
can also cause burns or injury. If any part of the
body comes in contact with the spray stream,
immediately consult a physician familiar with
injected fluid injuries.
Do not place your hand or any other part of your
body in front of the spray nozzle.
Original Instructions (EN)
Form No. 3403-794 Rev B
Operator's Manual
WARNING
CALIFORNIA
All Rights Reserved *3403-794* B
Printed in the USA

Advertisement

Table of Contents
loading

Summary of Contents for Toro 41621

  • Page 1 Whenever you need service, genuine Toro parts, or Note: additional information, contact an Authorized Service This product complies with all relevant Dealer or Toro Customer Service and have the model European directives. For details, please see the and serial numbers of your product ready. Figure 1 Declaration of Incorporation (DOI) at the back of this publication.
  • Page 2 • Do not leave the equipment under pressure when CAUTION you are not present. Chemicals are hazardous and can cause • Do not use the hand sprayer if the hose, trigger personal injury. lock, nozzle, or any other part is damaged or •...
  • Page 3: Table Of Contents

    Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. – No parts required Prepare the machine. Remove the optional rinse tank and move the sprayer tank—Multi Pro 5800 – No parts required turf sprayers with the optional rinse tank kit installed.
  • Page 4 Procedure Description Qty. Control valve T-fitting Hose clamp Cable tie R-clamp Hose (71 inches) Clamp 90° elbow Tube coupler Nut (1/4-20 inch) Install the control valve. Flange nut (3/8-16 inch) Pressure transducer tube Bolt (1/4-20 x 3/4 inch) Valve mount Control-valve bracket Bolt (6 x 12 mm) Washer (8 mm)
  • Page 5 Disconnect the positive battery cable from the positive post of the battery; refer to the Operator’s Manual. Preparing the Machine No Parts Required Removing the Rinse Tank Procedure and Moving the Spray Tank WARNING Multi Pro 5800 Turf Sprayers Battery terminals or metal tools could short with the Optional Rinse-Tank Kit against metal machine components, causing sparks.
  • Page 6 g244765 Figure 5 g244766 Figure 3 1. Retainer fork 3. Bulkhead fitting Moving the Spray Tank 90° fitting (supply hose) Remove the 90° fitting from the bulkhead fitting (Figure Remove the 2 bolts, 4 washers, and 2 flange locknuts that secure the 2 hold-down brackets for the rinse tank to the valve mount, and remove the hold-down brackets (Figure...
  • Page 7: Nut (1/4-20 Inch)

    Installing the Hose-Reel Frame Parts needed for this procedure: Nut (1/4-20 inch) Flange nut (5/16-18 inch) Flange nut (3/8-16 inch) Bolt (3/8-16 x 1 inch) Bolt (1/4-20 x 3/4 inch) Bolt (3/8-16 inch) Bolt (3/8-16 x 3 1/2 inch) Upper bracket Lower-bracket support Lower bracket Whiz bolt (5/16-18 x 1 inch)
  • Page 8 g027953 Figure 9 g027955 1. Bolt (1/4-20 x 3/4 inch) 4. Flange nut (5/16-18 inch) Figure 11 2. Upper bracket 5. Whiz bolt (5/16-18 x 1 1. Bolt (3/8-16 inch) 4. Lower bracket inch) 2. Lower support bracket 5. Bolt (3/8-16 x 3 1/2 inch) 3.
  • Page 9: Coupler

    x 1 inch), 2 bolts (3/8-16 x 2 1/4 inch), and 6 flange nuts (3/8-16 inch) as shown in Figure g027958 Figure 15 1. Pressure gauge 3. Pressure gauge support bracket assembly 2. Pressure gauge reducer 4. Coupler g027956 Figure 13 1.
  • Page 10 g244761 Figure 17 1. Retainer fork 3. Housing (suction screen) 2. 90° barbed fitting (supply hose) g244762 Figure 16 Secure the 90° barbed fitting to the housing for the suction screen with the retainer fork (Figure 1. Hold-down bracket 4. Washer (3/8 inch) 17).
  • Page 11: Wiring Harness

    Installing the Switch Box and Hose Reel Parts needed for this procedure: Wiring harness Switch box assembly Thrust washer Snap ring g028032 Figure 20 Hose reel assembly 1. Thrust washer 2. Snap ring Spring pin Washer (7/16 inch) Mount the switch box to the swivel plate using Flange nut (5/16-18 inch) 2 bolts (5/16-18 x 1/4 inch) and 2 flange nuts Bolt (5/16-18 x 1/4 inch)
  • Page 12: Bolt (5/16-18 X 1/4 Inch)

    Installing the Control Valve for the Hose Reel Parts needed for this procedure: Control valve T-fitting Hose clamp g023425 Figure 22 Cable tie 1. Flange nut (3/8-16 inch) 3. Bolt (3/8-16 x 1 inch) R-clamp 2. Washer (7/16 inch) Hose (71 inches) Clamp Install the washer and spring pin to the underside 90°...
  • Page 13 Assembling the Control Valve Removing the Control Valve from the Machine Multi Pro 5800 Turf Sprayers—2015 and Before Multi Pro 5800 Turf Sprayers—2016 and After Disconnect the 3-socket connector for the Disconnect the cap and coupler from the pressure transducer (Figure 25).
  • Page 14 Remove the flange clamp that secures 90° fitting to the 90° fitting with a connector for the sense tube, and remove the 90° fitting, gasket and flange clamp (Figure Preparing the Control Valve Multi Pro 5800 Turf Sprayers—2016 and After Assemble the valve mount onto the control valve as shown in A of Figure...
  • Page 15 Drilling the Manifold Mount Multi Pro 5800 Turf Sprayers—2016 and After Align the flange of the T-fitting with the flange of the 90° fitting with a connector for the sense tube (Figure 31). g033918 Figure 32 Remove the clamp, gasket, T-fitting with the flange from the 90°...
  • Page 16 Assembling the Control Valve Multi Pro 5800 Turf Sprayers—2016 and After Align the flange of the T-fitting with the flange of the 90° fitting with a connector for the sense tube (Figure 34). g033985 Figure 35 1. 3-socket connector 2. Pressure transducer Assemble the spray-wand hose onto the barbed-hose fitting of the control valve, and g033917...
  • Page 17 Assembling the Supply Hose and Pressure-Sense Tube to the Machine Secure the hose 180 cm (71 inches) to the upper bracket using a R-clamp, bolt (1/4-20 x 3/4 inch), and nut (1/4-20 inch) as shown in Figure g028038 Figure 38 2015 and before model shown;...
  • Page 18 Connect the battery cables as follows: WARNING Incorrect battery cable routing could Connecting the Spray Hose damage the machine and cables, causing sparks. Sparks can cause the battery gasses to explode, resulting in personal Parts needed for this procedure: injury. Spray-gun hose with fitting •...
  • Page 19 Operation WARNING Checking the Pivoting Hose Fluid under pressure can penetrate skin and cause injury. Reel for Leaks • Keep your body and hands away from nozzles that eject high-pressure fluid. No Parts Required • Do not aim the sprayer at any person or animal.
  • Page 20 Switching from Switching from Hand-Spray Boom-Spray Mode to Mode to Boom-Spray Mode Hand-Spray Mode CAUTION Hands, loose clothing, long hair, and loose WARNING jewelry could get caught in the hose and reel Driving while using the hand sprayer can while rewinding and cause injury. cause loss of control, resulting in injury or •...
  • Page 21 Notes:...
  • Page 22 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.
  • Page 23 The Way Toro Uses Information Toro may use your personal information to process warranty claims, to contact you in the event of a product recall and for any other purpose which we tell you about. Toro may share your information with Toro's affiliates, dealers or other business partners in connection with any of these activities. We will not sell your personal information to any other company.
  • Page 24 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer.

Table of Contents