1. Manuals
  2. Brands
  3. Toro Manuals
  4. Paint Sprayer
  5. Multi-Pro 5800
  6. Installation instructions manual

Toro Multi-Pro 5800 Installation Instructions Manual

Hide thumbs Also See for Multi-Pro 5800:
Table of Contents

Advertisement

Quick Links

Download this manual
Chemical Pre-Mix Kit
2015 and After Multi-Pro 5800 Turf Sprayer
Model No. 41622—Serial No. 315000001 and Up
This kit is designed to aid in the mixing of chemicals in
preparation for turf spray applications on well-maintained
lawns in parks, golf courses, sports fields, and on commercial
grounds. It is a dedicated attachment for a turf spray
application vehicle and is intended to be used by professional,
hired operators in commercial applications.
This product complies with all relevant European directives;
for details, please see the separate product specific Declaration
of Conformity (DOC) sheet.
Read this manual carefully to learn how to operate and
maintain your product properly. The information in this
manual can help you and others avoid injury and product
damage. Although Toro designs and produces safe products,
you are responsible for operating the product properly and
safely.
You may contact Toro directly at www.Toro.com for product
safety and operation training materials, accessory information,
help finding a dealer, or to register your product.
Whenever you need service, genuine Toro parts, or additional
information, contact an Authorized Service Dealer or Toro
Customer Service and have the model and serial numbers of
your product ready.
Figure 1
model and serial numbers on the product.
1. Model and serial number plate
Model No.
Serial No.
© 2015—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
illustrates the location of the
Figure 1
Register at www.Toro.com.
Installation Instructions
WARNING
CALIFORNIA
Proposition 65 Warning
This product contains a chemical or chemicals
known to the State of California to cause cancer,
birth defects, or reproductive harm.
Use of this product may cause exposure to
chemicals known to the State of California
to cause cancer, birth defects, or other
reproductive harm.
Original Instructions (EN)
All Rights Reserved *3395-538* A
Printed in the USA
Form No. 3395-538 Rev A

Advertisement

Table of Contents
loading

Related Manuals for Toro Multi-Pro 5800

Summary of Contents for Toro Multi-Pro 5800

  • Page 1 Although Toro designs and produces safe products, you are responsible for operating the product properly and safely. You may contact Toro directly at www.Toro.com for product safety and operation training materials, accessory information, help finding a dealer, or to register your product.

  • Page 2: Safety And Instructional Decals

    Safety WARNING Chemical substances used in the spray system may This manual identifies potential hazards and has safety be hazardous and toxic to you, bystanders, animals, messages identified by the safety alert symbol (Figure plants, soils, or other property. which signals a hazard that may cause serious injury or death •...

  • Page 3: Installation

    Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. Eductor valve assembly Flange nut (1/4 inch) Fitting (1 inch) Retainer pins Eductor valve bracket (The bracket may Install the eductor valve and hoses. already be installed from a previous kit installation) Relief hose (10 3/4 inches)
  • Page 4 Procedure Description Qty. Bulkhead O-ring Locking ring Retaining fork Forward hose assembly Install the forward hose. Gasket Worm-screw clamp R-clamp Carriage bolt (5/16 x 1 inch) Lock nut (5/16 inch) Supply hose Gasket Worm-screw clamp Install the supply hose. Hose clamp Hose adapter Retainer pin Note: Determine the left and right sides of the machine from the normal operating position.
  • Page 5 Figure 5 1. Bypass hose 3. Pump tee 2. Relief hose 4. Supply hose Figure 4 1. Nuts (existing) 5. Eductor valve bracket 7. Remove the horizontal hose tee from the side of the 2. Eductor valve bracket 6. Eductor valve assembly pump tee and attach it to the top of the pump tee 3.

  • Page 6: Assembling The Frame

    4. Install a lock nut over the lower exposed bolt passing through the frame to secure it to the tank strap (Figure Assembling the Frame Parts needed for this procedure: Support frame assembly Locknut (3/8 inch) Back plate assembly Cradle arm, right Cradle arm, left Bushing Pivot pin...
  • Page 7 Figure 9 1. Cradle arm, left 3. Set screw 2. Pivot housing 4. Holes in the cradle arm Figure 8 1. Back plate assembly 7. Handle 2. Hair pin 8. Bolt (3/8 x 1–1/4 inches) 3. Flat washer 9. Right cradle arm 4.
  • Page 8 plate assembly of the cradle to compress the spring tabs midway (Figure 11). Installing the Latching Components Parts needed for this procedure: Spring Installing the Springs 1. Install the spring in the hole in the lower end of the angled tab on the side of the frame assembly (Figure 10).
  • Page 9 Installing the Eductor Parts needed for this procedure: Eductor Handle Flange-head bolt Spring clamp Bolt (#10-24 x 1/2 inch) Locknut (#10-24) Bolt (3/8 x 1 inch) Locknut (3/8 inch) Figure 13 Flange-head nut 1. Handle 6. Flange-head bolt Hex-head bolt 2.
  • Page 10 10. Tighten the fasteners securing the eductor to the cradle. Note: Torque the fasteners to 36-45 N-m (27-33 ft-lb). 11. Tighten the 2 set screws on the left pivot arm. 12. Check the overall position of the eductor assembly on the tank strap.
  • Page 11 Installing the Bulkhead 1. Open the main tank lid and remove the filter screen. 2. Install the bulkhead and the O-ring up from inside the tank through the previously cut opening (Figure 18). Installing the Forward Hose Parts needed for this procedure: Bulkhead O-ring Locking ring...
  • Page 12 4. Install a lock nut over the bolt in the R-clamp and finger tighten at this time (Figure 19). Note: This will allow for later adjustment. 5. Attach the other end of the hose to the forward-facing Installing the Supply Hose opening of the eductor using a gasket and worm-screw clamp (Figure...

  • Page 13: Finishing The Installation

    Suction lance and hose (optional) Procedure Note: The suction lance and hose are optional accessories. Contact your Authorized Toro Distributor for more information. Retain the suction lance and hose for later use. Read and retain the remaining documentation on using the Chemical...

  • Page 14: Operation

    Handles and Transport Strap Operation Use the upper and lower handles to raise and lower the eductor and to lock it into the Transport position. CAUTION Chemicals are hazardous and can cause personal Main Valve injury. Use the main valve to introduce chemicals from the eductor •...
  • Page 15 For best results, use pressure up to 10 bar (150 psi) during stationary operation for additional heat protection. maximum. Contact your Authorized Toro Distributor to obtain a Toro heat-shield blanket kit for turf sprayers. 1. Insert the suction lance body into the eductor until the O-ring seals on the hopper drain.
  • Page 16 Figure 26 1. Suction lance 2. Eductor 2. Use the free end of the lance to pierce the bag or container to vacuum powdered or liquid chemical. 3. Place the lance end into a clean container of water to rinse the lance assembly. 4.

  • Page 17: Troubleshooting

    Troubleshooting Problem Possible Cause Corrective Action The eduction rate is low. 1. There is a lack of flow and pressure to 1. Increase the pump speed. Turn the the eductor system. agitation throttling toward the closed position. 2. The outlet/Inlet hose is obstructed. 2.
  • Page 18 Notes:...
  • Page 19 The Way Toro Uses Information Toro may use your personal information to process warranty claims, to contact you in the event of a product recall and for any other purpose which we tell you about. Toro may share your information with Toro's affiliates, dealers or other business partners in connection with any of these activities. We will not sell your personal information to any other company.
  • Page 20 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer.

This manual is also suitable for:

41622

Table of Contents