Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Toro Pro Control XP
Summary of Contents for Toro Pro Control XP
- Page 1 Form No. 3365-850 Rev D Pro Control™ XP Spray System Multi-Pro ® 5800 Turf Sprayer Model No. 41604—Serial No. 311000001 and Up To register your product or download an Operator's Manual or Parts Catalog at no charge, go to www.Toro.com. Original Instructions (EN)
-
Page 2: Table Of Contents
Computer............9 help finding a dealer, or to register your product. Displaying Data..........11 Note: If you are installing this kit (the Pro Control XP Self-Testing the Console Computer..... 11 Activating the Data Lock ........11 Spray System Kit) along with one or more other kits, Changing the Data Lock ........ -
Page 3: Safety
Safety Read and understand the contents of this manual before operating the console computer. • Keep this document with the Operator’s Manual for the Multi Pro ® 5800 Turf Sprayer. • It is very important that all who operate this equipment have ready access to these instructions at all times. -
Page 4: Setup
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. Mounting bracket Carriage bolt (5/16 x 3/4 inch) Locknut (5/16 inch) Install the console computer. Computer console assembly Hand Knob Pivot bracket Flowmeter Gasket Install the flowmeter. -
Page 5: Installing The Flowmeter
2. Locate the round, multi-pin console computer connectors on the main harness secured to the right frame member under the dashboard. 3. Cut the plastic tie that secures the console computer Installing the Flowmeter wiring to the frame under the dashboard. 4. - Page 6 D. Install the new gasket into the open side of the flowmeter body. E. Install the new worm clamp over the open end of the flowmeter. F. Carefully move the boom valve assembly into the position flush with the flowmeter body (Figure 7). G013878 Figure 5 3.
-
Page 7: Product Overview
Flow control switch Product Overview This switch allows you to automatically or manually control the spray system. There are 2 automatic positions and 1 manual position. Display The display shows the function and calibration data. Calibration keys 13881 These keys allow the operator to enter data into the console computer to calibrate the spray system. - Page 8 80 inches (204 cm) is set as the default. SPEED CAL Speed calibration number 148 (US or TU) or 38 (SI) is set as the starting point for all Toro sprayers. METER CAL Flowmeter calibration number Enter the number found on the flowmeter label or the tag on the flowmeter cable (Gal# for US or TU, or Liter# for SI).
-
Page 9: Operation
Operation the Off position and, while pressing and holding the [CE] key, turning the power switch to the On position. The console computer automatically controls the spray application rate for varying vehicle speeds. You set the Entering the Meter Cal Number target volume per unit area to spray and the console computer automatically maintains the flow within the Use the gallon calibration number for U.S. - Page 10 7. Enter a second target application rate (in U.S. gallons per acre, liters per hectare, or U.S. gallons per 1,000 sq. ft.) that you want to spray, if you desire. Note: Rate 2 should not differ more than 20% from Rate 1 unless there is a change in nozzle size. If you do not use a second rate, enter the same rate for Rate 1 and Rate 2.
-
Page 11: Displaying Data
Displaying Data Self-Testing the Console Computer To display the following data, do the following: The self test allows you to simulate the speed for testing Total Area the system when the vehicle is not moving. Press the [Total Area] key. 1. -
Page 12: Setting The Power Down Delay Time
Setting the Power Down Delay 9. Ensure that you have entered the proper values for the correct boom width and calibrations for Meter Time Cal, Rate 1, and Rate 2. To conserve the 12-volt battery on the vehicle, set the 10. -
Page 13: Initially Field-Testing The System
2. Press the [Speed] key to verify the speed readout. 3. Turn the Spray pump control switch to On. 4. Turn the Pro Control XP Power switch to the On position. 5. Turn the Foot switch to the On position. -
Page 14: Maintenance
4. Clean the turbine and the turbine hub to remove metal filings and any wettable powders. The settings in the Pro Control XP are automatically set 5. Inspect the turbine blades for wear. to the default settings. However, you can change the values if the nozzle spacing has changed. - Page 15 1. Press the [Boom 1 Cal] key. 9. If the readout is not between 490 feet and 510 feet (149 m and 155 m), calibrate the Speed Cal using 2. Press the [Enter] key. the following equation: 3. Enter 80 (US or TU) or 204 (SI). •...
-
Page 16: Calibrating The Flowmeter
3. Press the [Time] key. The display shows DAY. Corrected Meter Cal = (Meter Cal x Total Volume) / Amount of Water 4. Press the [Enter] key to change the day. Corrected Meter Cal = (1660 x 103) /100 5. Press the [Time] key. Corrected Meter Cal = 1710. -
Page 17: Troubleshooting
Troubleshooting Note: If the console computer malfunctions or needs repair, you can resume spraying in manual mode by unplugging the cables from the rear of the console computer. You can then control the system using the center console controls. Problem Possible Cause Corrective Action No display lights with the power on... - Page 18 Problem Possible Cause Corrective Action The rate is inaccurate or unstable 1. You incorrectly entered a number in the 1. Verify that all the numbers entered in console computer. the console computer are correct. 2. The wheel drive setting is not set to 2.
- Page 19 Notes:...