Table of Contents
Advertisement
Quick Links
GeoLink
Multi Pro
Model No. 41638
Model No. 41639
Introduction
The CL-55 modem kit updates the GeoLink® spray system. The GeoLink spray system is an attachment for
a turf spray application vehicle and is intended to be used by professional, hired operators in commercial
applications. It is designed primarily for spraying on well-maintained lawns in parks, golf courses, sports fields,
and on commercial grounds.
Visit
www.Toro.com
for product safety and operation training materials, accessory information, help finding a
dealer, or to register your product.
Contents
Introduction ............................................................... 1
Setup ........................................................................ 2
1 Getting a Current Copy of the Software
Guide and Quick Start Guide........................... 4
2 Preparing the Machine..................................... 4
3 Exporting Sprayer Display Inventory Item
Data ................................................................ 4
4 Removing the X30 Sprayer Display.................. 5
separately) ...................................................... 6
6 Verifying the U-Boot Firmware Version ............. 9
7 Updating the GeoLink Software ....................... 9
8 Disconnecting the Battery .............................. 12
9 Removing the Seat and the Engine-Access
Panel............................................................. 14
10 Removing the Right Front Fender ................ 15
Bracket.......................................................... 17
Machine ........................................................ 19
the Machine .................................................. 21
14 Removing the Terminating Resistor.............. 25
to the Machine .............................................. 25
16 Installing the CL-55 Modem ......................... 30
17 Connecting the Battery ................................ 34
18 Securing the Data Harness .......................... 37
19 Installing the Right Front Fender .................. 37
the Seat ........................................................ 38
Modem Kit..................................................... 40
22 Powering the GeoLink Components............. 40
© 2020-The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
CL-55 Modem Kit
®
1750 or 5800 Turf Sprayer
Register at www.Toro.com.
Installation Instructions
23 Configuring the GPS Correction
Source .......................................................... 41
24 Creating a Spray Job ................................... 43
25 Performing a Flow Meter Calibration ............ 43
26 Verifying the Cellular Status ......................... 44
27 Performing a Compass Calibration............... 44
28 Clearing NVRAM ......................................... 44
29 Performing a Compass Calibration............... 46
Original Instructions (EN)
All Rights Reserved *3439-786* A
Printed in the USA
Form No. 3439-786 Rev A
Advertisement
Table of Contents
Related Manuals for Toro GeoLink CL-55
Summary of Contents for Toro GeoLink CL-55
-
Page 1: Table Of Contents
20 Installing the Engine-Access Panel and the Seat ............38 21 Completing the Installation of the CL-55 Modem Kit............. 40 22 Powering the GeoLink Components..... 40 © 2020—The Toro® Company Register at www.Toro.com. Original Instructions (EN) All Rights Reserved *3439-786* A 8111 Lyndale Avenue South... - Page 2 – No parts required item data. – No parts required Remove the X30 sprayer display. X25 monitor kit (sold separately—Toro Install the X25 monitor kit. part No. 41637) – No parts required Verify the U-boot version. USB Drive (GeoLink X25 software version 4.04.40 or higher—CL-55...
-
Page 3: Source
Procedure Description Qty. CL-55 modem—GeoLink precision spray system kit (Model 41633 or Model 41634) Modem bracket Install the CL-55 modem. Capscrew (#10-24 x 1-1/2 inches) Spacer (1/4 x 3/4 inch) Locknut (#10-24) – No parts required Connecting the battery. – No parts required Secure the data harness. -
Page 4: Preparing The Machine
CCESS EVEL current copy of the Software Guide and Quick Start Guide from Toro.com. • GeoLink GSM systems use Toro Part No. 41634 • Geolink CDMA systems use Toro Part No. 41633 Important: After the CL-55 Modem Kit is installed, you must use the Software Guide for software version 4.04 and Up and Quick Start Guide for... -
Page 5: Data
Exporting Data Note: Do not use the USB drive from the CL-55 modem kit for exporting sprayer display data. Use the USB storage device that you use to backup GeoLink. Remove the cap from the USB port of the sprayer-display (Figure g323308 Figure 4... -
Page 6: Installing The X25 Monitor Kit
Figure 5 Parts needed for this procedure: 1. 26-pin connector (sprayer 2. 26-socket display) connector—data harness X25 monitor kit (sold separately—Toro part No. (sprayer monitor) 41637) Loosen the knob of the display arm (Figure Applying the Adhesive Strips to the Sprayer Monitor Clean the top surface of the X25 sprayer display with rubbing alcohol and a clean rag. - Page 7 Assembling the Display Hood to for the nut part of the threaded standoff (Figure the Sprayer Monitor At the back of the sprayer monitor and with the 2 connectors (26 pin) aligned down, remove the top locknut (5 mm) from the stud for the ball-pivot fitting (A of Figure g031280...
- Page 8 Mounting the Sprayer Monitor to Changing User Access Level the Dash Rotate the ignition key to the R (gasoline) or (diesel) position. REHEAT Loosen the knob of the monitor arm until you can slip both the ball pivot for the ball pivot at On the home screen, press the S icon.
- Page 9 Firmware Version No Parts Required Procedure Rotate the ignition key to the R (gasoline) or (diesel) position. REHEAT Press the System Information (Toro) icon at the top, left corner of the screen (Figure 15). g323340 Figure 13 1. I icon 2.
- Page 10 USB Drive (GeoLink X25 software version 4.04.40 or higher—CL-55 CDMA Modem Kit) Verifying the Software Version Rotate the ignition key to the RUN (gasoline) or PREHEAT/RUN (diesel) position. Press the ABOUT (Toro) icon at the upper left corner of the control console (Figure 16). g323321 Figure 17 1.
- Page 11 Important: Do not turn off machine power while the sprayer display applies the firmware upgrade. g323322 Figure 19 Remove the USB drive and install the USB port cap. Updating the AGI Firmware On the setup screen, press the S icon and YSTEM g323325 the GPS icon, and the R...
- Page 12 g323339 Figure 25 1. Current version (X.XX.XX) icon (ECU setup dialog box) In the ASC setting dialog box, press the ASC F 2.02.18 PGRADE IRMWARE TO VERSION icon, and press the confirm icon (Figure 26). Note: g024081 The options for an ASC firmware upgrade Figure 27 level higher that version 2.02.18 may display.
- Page 13 Disconnecting the Battery WARNING Multi Pro 5800 Machines Battery terminals or metal tools could short against metal components causing sparks. Sparks can cause the battery WARNING gasses to explode, resulting in personal Electrical sparks can cause the battery gasses injury. to explode, resulting in personal injury.
- Page 14 g024098 g029414 Figure 31 Figure 30 1. 2-socket connector 2. Seat-switch connector 1. Positive battery cable 3. Negative battery post (machine wire harness) 2. Positive battery post 4. Negative battery cable Remove the hairpin that secures the prop rod Disconnect the positive (red) cable from the to the bracket at the bottom of the seat plate battery post (Figure...
-
Page 15: Panel
Multi Pro 1750 Machines No Parts Required Procedure Note: If you damage the push-in fasteners removing them, replace the fasteners with Toro Part No. 117-2382. g037120 Figure 34 Remove the 2 capscrews (5/16 x 1 inch) and 2 washers (5/16 inch) that secure the bottom 1. - Page 16 g323165 Figure 37 1. Capscrew (5/16 x 1 inch) 3. Platform floor g323170 2. Washer (5/16 inch) 4. Right, front fender Carefully remove the 2 push-in fasteners that secure the right, front fender to the roll bar mounting channel (Figure 38).
-
Page 17: Installing The Modem-Antenna Bracket
Note: Retain the right, front fender, inner-fender shroud, capscrews, washers, and undamaged push-in fasteners for installation in 19 Installing the Right Front Fender (page 37). Replace damaged push-in fasteners with Toro Part No. 117-2382. - Page 18 Removing the RTK-Antenna Bracket Multi Pro 5800 Machines Remove the 2 nuts that secure the RTK-antenna bracket to the receiver mount, and remove the antenna bracket (Figure 44). g200697 Figure 42 Multi Pro 1750 Machines 1. Coaxial coupler 3. Jam nut 2.
- Page 19 Assembling the Modem-Antenna Bracket to the Receiver Mount Remove the 3 capscrews (5 x 16 mm) and 3 washers (5 mm) that secure the navigation receiver to the receiver mount (Figure 46 Figure 47). g314474 Figure 48 Multi Pro 1750 Machines 1.
-
Page 20: Installing The Modem Antenna To The Machine
Installing the Modem Antenna to the Machine Parts needed for this procedure: Modem antenna—GeoLink precision spray system kit (Model 41633 or Model 41634) Cable ties—GeoLink precision spray system kit g309766 Figure 51 (Model 41633 or Model 41634) 1. Modem antenna 2. -
Page 21: Assembling The Modem Data Harness To The Machine
g323031 Figure 53 Multi Pro 5800 Machines 1. Cable ties g315237 Figure 54 Secure the modem-antenna harness to the roll Multi Pro 1750 Machines bar with 5 cable ties as shown in Figure 52 Figure 1. RJ45 connector (labeled 2. 4-pin connector (labeled —modem data -55—modem CONSOLE... - Page 22 Routing the Modem Data Harness Multi Pro 1750 Machines Route the modem data harness along the data harness for the control console (Figure 57). g315306 Figure 57 g310206 Figure 56 1. Modem data harness 3. Data harness (control console) 1. RJ45 port (sprayer display) 4. Port seal nut 2.
- Page 23 g315308 Figure 59 1. Connectors 2. 4-pin connector (labeled (modem-antenna harness) -55—modem ETHERNET CL data harness) Routing the Modem Data Harness Multi Pro 5800 Machines g310208 Figure 61 Route the modem data cable through the storage compartment (Figure 60). 1. Modem data cable 2.
- Page 24 Securing the Navigation-Data and Electrical Harness, Modem-Antenna Harness, and Modem Data Harness Multi Pro 1750 Machines At the right, upper tube frame, bundle the navigation-data and electrical harness, and the CAN 2 ASC 10 BUS wire harness branch to the kit sprayer harness with 2 cable ties (Figure 65).
-
Page 25: Removing The Terminating Resistor
g314709 Figure 67 Multi Pro 1750 Machines g315768 1. 6-socket connector of the 2. Terminating resistor Figure 66 GeoLink data cable 1. Cable tie 3. Monitor tube 2. Modem-data harness 4. Navigation-data and electrical harness Secure the modem-data harness to the navigation-data and electrical harness with a cable tie as shown in Figure... -
Page 26: Assembling The Modem Power Harness
Assembling the Modem Power Harness to the Machine Parts needed for this procedure: g315594 Figure 70 Modem power harness—1850 mm (72-7/8 inches)—GeoLink precision spray system kit (Model 1. 9-pin connector (labeled 2. Ring terminals (labeled 41633 or Model 41634) RS232—modem power BATTERY and Cable ties—GeoLink precision spray system kit harness;... - Page 27 Routing the Modem Power Harness Multi Pro 5800 Machines Between the fuel tank bracket and the right, front fender, route the tab terminal (labeled ) and 2 ring terminals (labeled SWITCHED BATTERY ) of the modem power harness GROUND under the frame of the machine (Figure 72).
- Page 28 Routing the Harness to the Battery Multi Pro 5800 Machines Route the ring terminals of the harness labeled rearward, and over the BATTERY GROUND seat support (Figure 75). g301675 g315080 Figure 75 1. Modem power harness 2. Ring terminals (labeled BATTERY —modem power GROUND...
- Page 29 Insert the fuse (10 A) into the fuse-block socket your authorized Toro distributor. (Figure 78) for the options power circuit that you used in step 1. g323085 Figure 78 g323032 1. Fuse block 2.
-
Page 30: Installing The Cl-55 Modem
g301672 Figure 80 1. Fuse block 2. Fuse (10 A) Secure the switched power and ground branch of the kit wire harness to the machine wire harness with 5 cable ties. Installing the CL-55 Modem g310541 Figure 81 Parts needed for this procedure: 1. - Page 31 g310538 Figure 82 1. Coaxial connector (labeled 3. Violet coaxial push-in —modem-antenna connector (labeled harness) LTE-1—modem-antenna harness) 2. Blue coaxial push-in 4. Red coaxial push-in connector (labeled connector (labeled GNSS––modem-antenna LTE-2—modem-antenna harness) harness) g310539 Figure 83 Plug the blue coaxial push-in connector of the 1.
- Page 32 g315553 g315555 Figure 86 Figure 84 1. Slotted machine screw 4. CL-55 modem 1. Push-in fastener (machine 2. Prop-rod bracket (#10-24 x 1-1/2 inches) wire harness) 2. Modem bracket 5. Locknut (#10-24) 3. Spacer (1/4 x 3/4 inch) Remove the capscrew (1/4 x 3/4 inch) and flange locknut (1/4 inch) from the flange of the machine frame as shown in Figure...
- Page 33 g315554 Figure 88 1. Modem bracket 3. Prop-rod bracket 2. Push-in fastener (machine wire harness) Installing the Modem to the Machine Multi Pro 5800 Machines Assemble the modem bracket to the CL-55 modem with 2 capscrews (#10-24 x 1-1/2 inches), 2 spacers (1/4 x 3/4 inch), and 2 g310537 Figure 89 locknuts (#10-24) as shown in...
-
Page 34: Connecting The Battery
g310536 Figure 91 1. Flange locknut (5/16 inch) 3. Flange-head bolt (5/16 x 1 inch—air-cleaner mount) 2. Capscrew (5/16 x 3/4—coolant reservoir bracket) Assemble the modem bracket to the right seat-box panel and the coolant reservoir bracket (Figure 90 Figure 91) with the capscrew (5/16 x 3/4) and flange locknut (5/16). - Page 35 Battery-cable terminal (positive)—to the Align the insulator cover of the positive battery alternator (50 A) cable to the starter over the threaded post (Figure 92). Ring terminal—258 cm (101-1/2 inch) navigation-data and electrical harness Assemble the following wire and cable terminals branch (labeled (+)) BATTERY...
- Page 36 Assembling the Rear GeoLink Loosely secure the terminals and the T-bolt with a hex nut (Figure 94). Harness, Navigation-Data and Assemble a T-bolt through the negative terminal Electrical Harness, and Modem (black wire) of the rear wire harness, the Power Harness to the Battery negative terminal of the navigation-electrical harness, modem power harness, and terminal Cables...
-
Page 37: Securing The Data Harness
Gather the excess length of the data harness against the right, upper-frame tube (Figure 95). Note: Replace damaged the push-in fasteners with Toro Part No. 117-2382. Align the inner-fender shroud to the right, upper and right, lower-frame tubes (Figure 96). g202768 Figure 95 1. - Page 38 Secure the inner-fender shroud to the frame tubes (Figure 96) with the 6 push-in fasteners and 5 washers (9/16 x 1/2 inch). Align the right, front fender to the machine as shown Figure 97, and align the holes in the fender with the holes in the frame.
-
Page 39: Installing The Engine-Access Panel And The Seat
Installing the Engine-Access Panel and the Seat Multi Pro 1750 Machines g202000 Figure 102 No Parts Required 1. Seat plate 2. Seat Installing the Engine-Access Panel Align the holes in the pivot fittings of the seat pan with the holes in the chassis bracket (Figure Machines without the Tank Rinse Kit 103). -
Page 40: Completing The Installation Of The Cl-55 Modem Kit
Assemble the prop rod to the bracket of the seat with the washer and hairpin (Figure 104). Completing the Installation of the CL-55 Modem Kit No Parts Required Closing the Seats Multi Pro 5800 Machines Move the prop rods for the seats into the slots and tilt the seats down. - Page 41 g302922 Figure 107 indicator (satellite receiver) g302923 • Modem—the LED indicators illuminate Figure 110 (Figure 108 Figure 109). 1. Back of the machine indicator STATUS (automatic section controller) Turn the ignition key to the O position. Verify that power is shut off at the following components: •...
- Page 42 g324475 g324474 Figure 111 Figure 113 1. C icon 2. Confirm icon 1. GPS icon ONSOLE On the GPS Correction Source screen, press Note: The NT icon displays the OURCE the NT icon (Figure 111). OURCE console source (Figure 114). When the Correction Source Setup wizard displays, press the next icon (Figure...
- Page 43 Creating a Spray Job No Parts Required Procedure Press the Job Menu and press the C REATE icon (Figure 115). g304039 Figure 116 1. N icon 3. Confirm icon OZZLE 2. Nozzle selection list icons In the nozzle selection list, press any nozzle icon, and press the confirm icon (Figure 116).
- Page 44 -99 dBm. Verifying the Cellular Status Note: If the modem signal is equal to or less than -100 dBm, contact your authorized Toro distributor, Toro NSN at 1-844-GEOLINK No Parts Required (1-844-436-5465), or NSNTech@toro.com for customer service. Procedure Swipe the F...
- Page 45 No Parts Required Changing the Setup Screen for Dealer Access Important: You must erase the nonvolatile RAM g309146 at the customer location. Figure 121 Contact Toro NSN at 1-844-GEOLINK 1. P icon 3. A icon ASSWORD CCESS EVEL (1-844-436-5465) or NSNTech@toro.com for 2.
- Page 46 Erasing the Nonvolatile RAM In the setup screen, press the S icon, YSTEM GPS icon, and A icon DVANCED ONFIGURATION (Figure 124). g309148 Figure 126 1. E icon ETUP Changing the User Access Level to Standard Mode On the setup screen, press the U icon, press the A icon...
- Page 47 Performing a Compass Calibration At the Customer Location No Parts Required Procedure Perform a compass calibration at the customer’s location; refer to Calibrating the Compass in the Operator’s Manual or Software Guide for your GeoLink system.