Ethernet Phy1 And Phy2 - Siemens ERTEC200 Manual

No. Function 1 Function 2
LBU PHY Debug
GPIO[44:32]
Config Config
(6,5,2)=xx0b (6,5,2)=011b
166 LBU_D12 SMI_MDC
167 LBU_D13 SMI_MDIO
168 LBU_D14 RES_PHY_N
169 LBU_D15 GPIO41
170 LBU_RDY_N GPIO42
171 LBU_IRQ0_N GPIO43
172 LBU_IRQ1_N GPIO44
1.5.8

Ethernet PHY1 and PHY2

No. Signal Name
173 DGND4
174 DVDD4
175 DVDD3
176 DGND3
177 P2VDDARXTX
178 P2VSSARX
179 P2RxN
180 P2RxP
181 P2VSSATX1
182 P2TxN
183 P2TxP
184 P2VSSATX2
185 P2RDxP
186 P2RDxN
187 P2TDxP
188 P2TDxN
189 P2SDxP
190 P2SDxN
191 VSSAPLLCB
192 VDDACB
193 VDDAPLL
194 EXTRES
195 ATP
Copyright © Siemens AG 2007. All rights reserved.
Technical data subject to change
Function 3
ETM Trace
and and
GPIO[44:32]
Config
(6,5,2)=101b
LBU / MII-Interface
GPIO41
GPIO42
GPIO43
GPIO44
PHY1 and PHY2
Function 4 IO
(Reset
See
Config
Reserved
[6,5,2])
[6,5,2]=111b
B/O/I/O
(LBU : I)
B/O/I/O
(LBU : I)
B/O/I/O
(LBU : I)
B/B/B/B
(GPIO:I)
(LBU : I)
O/B/B/B
(GPIO:I)
O/B/B/B
(GPIO:I)
O/B/B/B
(GPIO:I)
I/O Pull- PIN
No.
I T17
I R21
I R22
I R17
I N18
I N17
B P22
B P21
I M18
B M21
B M22
I L19
I U22
I U21
O Y21
O W21
I V19
I U18
I L18
I H22
I K19
B L21
B L22
18
Pull PIN Comment
- No.
up W14 LBU or MII
up V15 LBU or MII
up V16 LBU or MII
up W16 LBU or GPIO
up W19 LBU or GPIO
LBU-Mode:
LBU_RDY signal:
Polarity depends on
Input CONFIG[6];
Output active while
LBU_CS_R/M_N is
active
up AA21 LBU or GPIO
LBU-Mode: Low-active
interrupt (no open
drain)
up W18 LBU or GPIO
LBU-Mode: Low-active
interrupt (no open
drain)
Comment
Digital GND supply
Digital 1.5 V supply
Digital 1.5 V supply
Digital GND supply
Analog Port Tx/Rx 1.5 V supply
Analog port GND supply
Port2 differential receive input
Port2 differential receive input
Analog port GND supply
Port2 differential transmit output
Port2 differential transmit output
Analog port GND supply
Port2 FX differential receive input
Port2 FX differential receive input
Port2 FX differential transmit
output
Port2 FX differential transmit
output
Port2 FX differential SD input
Port2 FX differential SD input
Analog central GND supply
Analog central 3.3 V supply
Analog central 1.5 V supply
Resistor reference 12.4 kOhm
Analog test function
ERTEC 200 Manual
Version 1.1.0