GE t60 Instruction Manual page 92

5.2 PRODUCT SETUP
When using the User Maps for DNP data points (Analog Inputs and/or Binary Inputs) for relays with ether-
net installed, check the "DNP Points Lists" T60 web page to ensure the desired points lists are created.
This web page can be viewed using a web browser by entering the T60 IP address to access the T60 "Main
NOTE
Menu", then by selecting the "Device Information Menu" > "DNP Points Lists" menu item.
f) UCA/MMS PROTOCOL
PATH: SETTINGS PRODUCT SETUP
UCA/MMS PROTOCOL
The T60 supports the Manufacturing Message Specification (MMS) protocol as specified by the Utility Communication
Architecture (UCA). UCA/MMS is supported over two protocol stacks: TCP/IP over ethernet and TP4/CLNP (OSI) over eth-
ernet. The T60 operates as a UCA/MMS server. The Remote Inputs/Outputs section in this chapter describe the peer-to-
peer GOOSE message scheme.
5
The
UCA LOGICAL DEVICE
located. The
GOOSE FUNCTION
testing or to prevent the relay from sending GOOSE messages during normal operation. The
selects a FlexLogic™ operand to provide the state of the UCA GLOBE.ST.LocRemDS data item. Refer to Appendix C:
UCA/MMS Communications for additional details on the T60 UCA/MMS support.
g) WEB SERVER HTTP PROTOCOL
PATH: SETTINGS PRODUCT SETUP
WEB SERVER
HTTP PROTOCOL
The T60 contains an embedded web server and is capable of transferring web pages to a web browser such as Microsoft
Internet Explorer or Netscape Navigator. This feature is available only if the T60 has the ethernet option installed. The web
pages are organized as a series of menus that can be accessed starting at the T60 "Main Menu". Web pages are available
showing DNP and IEC 60870-5-104 points lists, Modbus registers, Event Records, Fault Reports, etc. The web pages can
be accessed by connecting the UR and a computer to an ethernet network. The Main Menu will be displayed in the web
browser on the computer simply by entering the IP address of the T60 into the "Address" box on the web browser.
h) TFTP PROTOCOL
PATH: SETTINGS PRODUCT SETUP
TFTP PROTOCOL
The Trivial File Transfer Protocol (TFTP) can be used to transfer files from the UR over a network. The T60 operates as a
TFTP server. TFTP client software is available from various sources, including Microsoft Windows NT. The dir.txt file
obtained from the T60 contains a list and description of all available files (event records, oscillography, etc.).
5-14
COMMUNICATIONS
DEFAULT GOOSE UPDATE
TIME: 60 s
UCA LOGICAL DEVICE:
MESSAGE
UCADevice
UCA/MMS TCP PORT
MESSAGE
NUMBER:
GOOSE FUNCTION:
MESSAGE
Enabled
GLOBE.ST.LocRemDS:
MESSAGE
Off
setting represents the MMS domain name (UCA logical device) where all UCA objects are
setting allows for the blocking of GOOSE messages from the T60. This can be used during
COMMUNICATIONS
HTTP TCP PORT
NUMBER:
COMMUNICATIONS
TFTP MAIN UDP PORT
NUMBER:
TFTP DATA UDP PORT 1
MESSAGE
NUMBER:
TFTP DATA UDP PORT 2
MESSAGE
NUMBER:
T60 Transformer Management Relay
UCA/MMS PROTOCOL
Range: 1 to 60 s in steps of 1. See UserSt Bit Pairs in the
Remote Outputs section of this Chapter.
Range: Up to 16 alphanumeric characters representing
the name of the UCA logical device.
Range: 1 to 65535 in steps of 1
102
Range: Disabled, Enabled
Range: FlexLogic™ operand
WEB SERVER HTTP PROTOCOL
Range: 1 to 65535 in steps of 1
80
TFTP PROTOCOL
Range: 1 to 65535 in steps of 1
69
Range: 0 to 65535 in steps of 1
0
Range: 0 to 65535 in steps of 1
0
5 SETTINGS
setting
GLOBE.ST.LocRemDS
GE Multilin