ABB AC500 Introduction Manual page 74

Setting of the slave address of the FBP plug onto the S500-FBP interface module
The FieldBusPlug needs to get an address to be used into a fieldbus as a slave module. The S500-FBP
Interface Module gives them an address at power-up of the system. The address should be set
according to 2 rotary switches located on the top of the module.
Up to 99 addresses can be then set with the switches.
Rotary switch for setting
the FBP slave address
A screwdriver with a
width of 2.5 mm to 3 mm
is required
ADDR
x10
ADDR
x1
Figure: Setting the FBP slave address
The two rotary switches labelled ADDR x 1 and ADDR x 10 are used to assign an address to the
FieldBusPlug.
For example: to assign the address 25 to the station, turn the rotary switch ADDRx10 to the position 2
and the ADDRx1 to the position 5, then the resulting address is 2x10 + 5x1 = 25.
Same example but for the address 6: turn the ADDRx10 to 0 and the ADDRx1 to 6, then the resulting
address is 0x10 + 6x1 = 6.
ATTENTION
Make the Connection of the FieldBusPlug to the Fieldbus Master Device
The FieldBusPlug module has to be connected to the master device and the power supply has to be
provided. Please use the dedicated accessories to the FBP used for the desired Fieldbus.
Refer to the FBP documentation for the installation instructions.
____________________________________________________________________________________________________________
G1
Introduction to AC500
PWR
FBP
S-ERR
I/O-Bus
ADDR
x10
ADDR
x1
If the address set on the FBP Interface Module is different from those assigned
into the Fieldbus configurator software of the Master device for that station, the
station could not be accessed and the complete fieldbus could not work
properly or be completely down!
DC505
1.0 I0 2.0 C8 1.0 I0 2.0
1.1 I1 2.1 C9 1.1 I1 2.1
1.2 I2 2.2 C10 1.2 I2 2.2 I10
1.3 I3 2.3 C11 1.3 I3 2.3 I11
1.4 I4 2.4 C12 1.4 I4 2.4 I12
1.5 I5 2.5 C13 1.5 I5 2.5 I13
1.6 I6 2.6 C14 1.6 I6 2.6 I14
1.7 I7 2.7 C15 1.7 I7 2.7 I15
1.8 UP 2.8 UP 1.8 UP 2.8 UP
1.9 ZP 2.9 ZP 1.9 ZP 2.9 ZP
CH-ERR1 CH-ERR2 CH-ERR1 CH-ERR2
FBP 8 DI 8 DC
Input 24 V DC
Output 24 V DC 0.5 A
1.0 2.0 1.0
1.1 2.1 1.1
1.2 2.2 1.2
1.3 2.3 1.3
1.4 2.4 1.4
1.5 2.5 1.5
1.6 2.6 1.6
1.7 2.7 1.7
1.8 2.8 1.8
1.9 2.9 1.9
1-72
DC532
I8 3.0 C16 4.0 C24
I9 3.1 C17 4.1 C25
3.2 C18 4.2 C26
3.3 C19 4.3 C27
3.4 C20 4.4 C28
3.5 C21 4.5 C29
3.6 C22 4.6 C30
3.7 C23 4.7 C31
3.8 UP 4.8 UP
3.9 ZP 4.9 ZP
CH-ERR3 CH-ERR4
16 DI 16 DC
Input 24 V DC
Output 24 V DC 0.5A
2.0 3.0 4.0
2.1 3.1 4.1
2.2 3.2 4.2
2.3 3.3 4.3
2.4 3.4 4.4
2.5 3.5 4.5
2.6 3.6 4.6
2.7 3.7 4.7
2.8 3.8 4.8
2.9 3.9 4.9
AC500 / Issued: 07.2006