Function Setting Operation - Canon J1 Service Manual

5
Adjustment > Basic Adjustment > Function Setting Operation

Function Setting Operation

The following are items of the function setting and use scenes.
The setting procedure is as follows.
NO Item
[1] Setting the Upward Curl Prevention
Mode
[2] Setting the Downward Curl Prevention
Mode
[3] Setting the Thick Paper Curl
Prevention Mode
[4] Setting the Thick Paper Pushing
Forward Prevention Mode
[5] Setting the Poor Offset Stacking
Prevention Mode
[6] Setting the Poor Stacking of Thin
Paper Prevention Mode
[7] Setting the Staple Stack Position
Change Prevention Mode
[8] Setting the Tray Switching Noise
Reduction Mode
[9] Setting the Tray Switching Speedup
Mode
[10] Setting the Finisher Noise Reduction
Mode
[11] Setting the 1-Sheet Shift Sort Enabled
Mode
[12] Setting the Saddle Stacking Capacity
Switching Mode
[13] Setting the Saddle Stack Alarm
Detection Disabled Mode
[14] Poor Large/Thin Paper Stack
Prevention Mode
[15] Poor Non-Sort Delivery Stack
Prevention Mode
[16] Set Occasional Misalignment
Prevention Mode
[17] Change of Paper Stack Speed for
Buffered Paper Mode
[18] Setting Finisher Buffer Operation
Mode
5
Adjustment > Basic Adjustment > Function Setting Operation
Use case
When the upper curl occurs on the paper
delivered to the stack tray.
When the lower curl occurs on the paper
delivered to the stack tray.
When the upper curl occurs at the thick paper
delivery.
When the previous delivery paper is pushed by
the next delivery paper.
When the stack fault occurs in the small paper
offset mode.
When the stack fault occurs with the thin
paper.
When the top paper is displaced in the stapling
delivery mode.
When the switch sound for the stack tray shift
is noisy.
When the switch time for the stack tray shift is
long.
When the movement sound for the finisher is
noisy.
When the 1-sheet shift sort enabled mode is
necessary.
When large/thin paper is not appropriately
stacked.
When the paper delivered with non-sort mode
is not appropriately stacked.
When large/thin paper is not appropriately
stacked.
When the paper delivered with non-sort mode
is not appropriately stacked.
When misalignment in feed direction occurs
occasionally for thin/plain paper.
When the alignment failure occurs in the sort
or staple mode.
When misalignment of paper stack occurs in
staple mode for small size papers.
T-5-3
1) Turn off the host machine.
2) Remove the rear cover of finisher.
3) Set the bits of DSW1 on the finisher controller PCB as follows:
ON
1 2 3 4 5 6 7 8
F-5-26
4) Turn on the host machine.
5) Set the DSW1 on the finisher controller PCB as follows.
NO Item
[1] Setting the Upward Curl Prevention Mode
[2] Setting the Downward Curl Prevention Mode
[3] Setting the Thick Paper Curl Prevention Mode
[4] Setting the Thick Paper Pushing Forward Prevention Mode ON:2,7,8
[5] Setting the Poor Offset Stacking Prevention Mode
[6] Setting the Poor Stacking of Thin Paper Prevention Mode
[7] Setting the Staple Stack Position Change Prevention Mode ON:2,5
[8] Setting the Tray Switching Noise Reduction Mode
[9] Setting the Tray Switching Speedup Mode
[10] Setting the Finisher Noise Reduction Mode
[11] Setting the 1-Sheet Shift Sort Enabled Mode
[12] Setting the Saddle Stacking Capacity Switching Mode
[13] Setting the Saddle Stack Alarm Detection Disabled Mode
[14] Poor Large/Thin Paper Stack Prevention Mode
[15] Poor Non-Sort Delivery Stack Prevention Mode
[16] Set Occasional Misalignment Prevention Mode
[17] Change of Paper Stack Speed for Buffered Paper Mode
[18] Setting Finisher Buffer Operation Mode
5-15
Bit setting of DSW1 in the
finisher controller PCB
ON:2
ON:2,8
ON:2,7
ON:2,6
ON:2,6,8
ON:2,5,6
ON:2,5,6,7
ON:2,5,6,8
ON:2,4
ON:2,4,8
ON:2,4,7
ON:2,6,7
ON:1,2,5,6,7,8
ON:2,6,7,8
ON:2,5,7
ON:2,5,8
T-5-4
5-15