Toro Z400 Series Z Master Setup Instructions
  1. Manuals
  2. Brands
  3. Toro Manuals
  4. Lawn Mower
  5. Z400 Series Z Master
  6. Setup instructions
Toro Z400 Series Z Master Setup Instructions

Toro Z400 Series Z Master Setup Instructions

Hide thumbs Also See for Z400 Series Z Master:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Operator's Manual
Z400 Series Z Master
For all Z 400 Series Z Master Mowers

Loose Parts

Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
5
6
7
8
9
10
11
12
13
© 2008—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Description
No parts required
No parts required
Rear wheels
Roll bar, right section
Roll bar, left section
Roll bar, center section
Bolt, (3/8 x 1 inch)
Curved washer
Flange nut, (3/8 inch)
Bolt, (1/2 x 3–1/4 inch)
Flange nut, (1/2 inch)
No parts required
Right control lever
Left control lever
Bolt (3/8 x 1 inch) (2 are assembled)
Curved washer (3/8 inch) (2 are
assembled)
No parts required
No parts required
Air cleaner cap
Hose clamp
Number 2 general purpose lithium base
or molybdenum base grease. (Purchase
separately.)
No parts required
No parts required
No parts required
Register at www.Toro.com.
®
Mowers
Qty.
–
Remove parts from the crate.
–
Check the tire pressure.
2
Install the drive wheels.
1
1
1
8
Install the Rollover Protection System
(ROPS).
8
8
2
2
–
Install the seat.
1
1
Install the motion control levers.
4
4
–
Adding fuel to the machine.
–
Charge the battery.
1
Install the air cleaner cap.
1
1 tube
Check the machine for grease.
–
Check the engine oil level.
–
Prepare the side discharge chute.
Check the machine before delivery to
–
the customer.
Form No. 3356-183 Rev B
Setup Instructions
Use
Original Instructions (EN)
Printed in the USA.
All Rights Reserved

Advertisement

Table of Contents
loading

Related Manuals for Toro Z400 Series Z Master

Summary of Contents for Toro Z400 Series Z Master

  • Page 1: Loose Parts

    Form No. 3356-183 Rev B Z400 Series Z Master ® Mowers For all Z 400 Series Z Master Mowers Setup Instructions Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. – No parts required Remove parts from the crate.

  • Page 2: Checking The Tire Pressure

    Procedure Description Qty. Operator’s Manual Parts Catalog Engine Owner’s Manual Delivering the machine to the customer. Registration Card Safety Video Removing Parts from the Crate Raising the Machine Up and Installing the Drive Wheels No Parts Required Parts needed for this procedure: Procedure Rear wheels Remove the tires, the seat and the parts for the ROPS...

  • Page 3: Installing The Roll Over Protection System

    Installing the Roll Over Protection System Parts needed for this procedure: Roll bar, right section Roll bar, left section Roll bar, center section Bolt, (3/8 x 1 inch) Figure 3 Curved washer Flange nut, (3/8 inch) Bolt, (1/2 x 3–1/4 inch) 3.
  • Page 4 2. Install the lanyard clips onto the long bolts (1/2 x 3-1/4 inch). Note: Make sure the bent tab points toward the head of the bolt. Figure 7 3. Lightly oil the ends of the center roll bar section. Figure 9 4.

  • Page 5: Installing The Seat

    Figure 12 5. Install the seat rod to the seat frame. Figure 11 Installing the Seat No Parts Required Figure 13 Procedure 1. Remove the bolt and nut from the seat frame. 2. Remove the nuts from the studs under the seat. 3.

  • Page 6: Adding Fuel To The Machine

    Note: Install the control levers in the top and middle holes for the high position or the middle and bottom holes for the low position, as desired. Adding Fuel to the Machine No Parts Required Procedure Add fuel to the machine before starting it. Refer to your Operator’s Manual.

  • Page 7: Installing The Air Cleaner Cap

    2. Remove the air cleaner cap from the machine. 3. Install the hose clamp onto the air cleaner cap. Figure 16 Figure 18 4. Install the air cleaner cap onto the air cleaner and secure it with the hose clamp. Installing the Air Cleaner Cap Parts needed for this procedure: Air cleaner cap...

  • Page 8: Checking The Engine Oil Level

    Checking the Machine for Checking the Engine Oil Level Grease No Parts Required Parts needed for this procedure: Procedure Number 2 general purpose lithium base or 1 tube Before you start the engine and use the machine, check molybdenum base grease. (Purchase separately.) the oil level in the engine crankcase;...
  • Page 9 Checking the Machine Before Delivery to the Customer No Parts Required Procedure Before delivering the machine to the customer, ensure that you perform or have performed the procedures listed in the following table and initial each when finished. Refer to the Operator’s Manual for instructions on performing these procedures.
  • Page 10 Delivering the Machine to the Customer Parts needed for this procedure: Operator’s Manual Parts Catalog Engine Owner’s Manual Registration Card Safety Video Procedure At delivery, complete the items listed in the following table and initial each when finished. Model No. Serial No.
  • Page 11 Describe the post sale service procedures for your store. Assist the customer in filling out and mailing the registration card or register online at www.Toro.com Make sure that the customer receives the Operator’s Manual, Parts Catalog, and Engine Owner’s Manual, Set Up Instructions, and safety video.

Table of Contents