Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Operator's Manual
Z400 Z Master
With 122cm TURBO FORCE
Model No. 74450TE—Serial No. 310000001 and Up
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
5
6
7
8
9
10
11
12
13
© 2010—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
Description
No parts required
No parts required
Rear wheels
Roll bar, right section
Roll bar, left section
Roll bar, center section
Bolt, (3/8 x 1 inch)
Curved washer
Flange nut, (3/8 inch)
Bolt, (1/2 x 3–1/4 inch)
Flange nut, (1/2 inch)
Lefthand armrest
Flat washer
Bolt, (1/2 x 3-1/4 inches)
Plastic flat washer
Spacer
Right control lever
Left control lever
Bolt (3/8 x 1 inch) (2 are assembled)
Curved washer (3/8 inch) (2 are
assembled)
No parts required
No parts required
Air cleaner cap
Hose clamp
Number 2 general purpose lithium base
or molybdenum base grease. (Purchase
separately.)
No parts required
No parts required
No parts required
Register at www.Toro.com.
®
Side Discharge Mower
Qty.
–
Remove parts from the crate.
–
Check the tire pressure.
2
Install the drive wheels.
1
1
1
8
Install the Rollover Protection System
(ROPS).
8
8
2
2
1
1
1
Install the seat.
1
1
1
1
Install the motion control levers.
4
4
–
Adding fuel to the machine.
–
Charge the battery.
1
Install the air cleaner cap.
1
1 tube
Check the machine for grease.
–
Check the engine oil level.
–
Prepare the side discharge chute.
Check the machine before delivery to
–
the customer.
Form No. 3365-100 Rev A
Setup Instructions
Use
Original Instructions (EN)
Printed in the USA.
All Rights Reserved
Advertisement
Table of Contents
Related Manuals for Toro 74450TE
Summary of Contents for Toro 74450TE
-
Page 1: Loose Parts
Form No. 3365-100 Rev A Z400 Z Master ® With 122cm TURBO FORCE ® Side Discharge Mower Model No. 74450TE—Serial No. 310000001 and Up Setup Instructions Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. -
Page 2: Checking The Tire Pressure
Procedure Description Qty. Operator’s Manual Engine Owner’s Manual Registration Card Delivering the machine to the customer. Operator training material Removing Parts from the Crate Raising the Machine Up and Installing the Drive Wheels No Parts Required Parts needed for this procedure: Procedure Rear wheels Remove the tires, the seat and the parts for the ROPS... -
Page 3: Installing The Roll Over Protection System
3. Remove the wheel nuts from both sides of the vehicle and remove the right angle retaining plate. Discard the screws and retaining plate. Installing the Roll Over Protection System Parts needed for this procedure: Roll bar, right section Roll bar, left section Roll bar, center section Figure 4 Bolt, (3/8 x 1 inch) - Page 4 2. Install the lanyard clips onto the long bolts (1/2 x 3-1/4 inch). Note: Make sure the bent tab points toward the head of the bolt. Figure 7 3. Lightly oil the ends of the center roll bar section. 4. Loosely install the center roll bar section using 2 bolts (1/2 x 3-1/4 inch) and 2 flange nuts (1/2 inch).
-
Page 5: Installing The Seat
Installing the Seat Parts needed for this procedure: g012851 Lefthand armrest Figure 12 Flat washer 1. Spacer 3. Bent ends Bolt, (1/2 x 3-1/4 inches) 2. Slot– install to the rear of seat Plastic flat washer Spacer 5. Install the seat and spacers to the seat frame with the previously removed nuts. -
Page 6: Installing The Motion Control Levers
Figure 14 Installing the Motion Control Levers Parts needed for this procedure: Right control lever Left control lever Bolt (3/8 x 1 inch) (2 are assembled) Curved washer (3/8 inch) (2 are assembled) Figure 16 Procedure Note: If the machine is not properly tracking, refer 1. -
Page 7: Charging The Battery
Charging the Battery Installing the Air Cleaner Cap No Parts Required Parts needed for this procedure: Air cleaner cap Procedure Hose clamp WARNING Procedure Charging the battery produces gasses that can explode and cause serious injury. 1. Remove the plastic plug. •... -
Page 8: Checking The Engine Oil Level
Checking the Machine for Grease Parts needed for this procedure: Number 2 general purpose lithium base or 1 tube molybdenum base grease. (Purchase separately.) Figure 19 Procedure 4. Install the air cleaner cap onto the air cleaner and 1. Check the tensioning arm for grease. secure it with the hose clamp. - Page 9 Preparing the Side Discharge Chute No Parts Required Procedure Remove the plastic tie holding the side discharge chute up and lower the chute into place. Check and ensure the spring is installed correctly. The grass deflector must be able to lower down into position. Lift the deflector up to test that it lowers into the full down position.
- Page 10 Checking the Machine Before Delivery to the Customer No Parts Required Procedure Before delivering the machine to the customer, ensure that you perform or have performed the procedures listed in the following table and initial each when finished. Refer to the Operator’s Manual for instructions on performing these procedures.
- Page 11 Delivering the Machine to the Customer Parts needed for this procedure: Operator’s Manual Engine Owner’s Manual Registration Card Operator training material Procedure At delivery, complete the items listed in the following table and initial each when finished. Model No. Serial No.
- Page 12 Make sure that the customer receives the Operator’s Manual, Engine Owner’s Manual, Set Up Instructions, and operator training material. Make sure the customer knows the Parts Catalog is available at www.Toro.com. Assist the customer in loading the mower. Note: When you, the dealer representative, have finished delivering the machine to the customer, sign and date in the space provide below and keep a copy of this page for dealer records.