Advertisement
Quick Links
Cordless Hammer Drill
Capacities
Steel
Wood
Wood
s c r e w
Concrete
1 0 mm
( 3 / 8 " )
2 1 mm I 1 3 / 1 6 " )
7 1 ; 4 m :
~~~~1~~
1 0
mm
( 3 / 8 " )
Equipped with electric brake
MODEL 8411D
MODEL 8411DW
With Fast Charger
No load speed
( R P M )
High
LOW
0
~
1 , 1 5 0
0
- -
3 7 0
INSTRUCTION MANUAL
0
~
1 2 , 7 0 0
1 . 8 7
k g (4 2 I b s )
2 7 3
mm
x
7 9
mm
x
2 2 0
mm
110-3/4"
x
3 - 1 / 8 "
x 8 - 5 / 8 " )
0
~
4,100
Voltage
Input
o u t p u t
Charging time
Manufacturer reserves t h e right t o change specifications w i t h o u t notice.
Note: Specifications may differ from country t o country.
Advertisement
Related Manuals for Makita 8411D
Summary of Contents for Makita 8411D
- Page 1 ~~~~1~~ 2 7 3 110-3/4” 3 - 1 / 8 ” x 8 - 5 / 8 ” ) Input MODEL 8411D MODEL 8411DW With Fast Charger No load speed ( R P M ) High ( 3 / 8 ” )
- Page 2 SAFETY I N STRUCTI WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT.
- Page 3 REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turning AVOID UNINTENTIONAL STARTING. Don’t carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. OUTDOOR USE EXTENSION CORDS.
-
Page 4: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS Length of Cord (Feet) AWG Size of Cord Do not operate charger w i t h damaged cord or plug mediately. Do not operate charger if otherwise damaged in any way; take it t o a qualified serviceman. Do not disassemble charger or battery cartridge;... -
Page 5: Additional Safety Rules
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C or ABOVE 4OoC (104OF). 2. Do not attempt t o use a step-up transformer, an engine generator or DC power receptacle. not allow anything t o cover or clog the charger vents. - Page 6 Installing or removing battery cartridge .Always switch off the tool before insertion or removal of the battery cartridge. .To remove the battery cartridge, pull out plate on the tool and grasp both sides of the cartridge while withdrawing from the tool. insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip...
- Page 7 Installing or removing drill bit or driver bit CAUTION : Always be sure that the tool is switched off and the battery cartridge installing or removing the bit. To install the bit, push the sleeve up to- ward the "FREE" side and turn the sleeve counterclockwise while holding the ring Place the bit in the chuck as far as go.
- Page 8 Switch action Tool speed is increased by increasing pres- sure on the trigger. To start the tool, simply pull the trigger. Release the trigger to stop. CAUTION : Before inserting the battery cartridge into the tool, always check to switch actuates properly and returns t o the "OFF" position when released. Reversing switch action This tool has a reversing switch to change the direction of rotation.
- Page 9 Operation 1) Hammer drilling operation When drilling in concrete, granite, turn the knob so that the a mark etc., on the knob points to the sure to use a tungsten-carbide tipped bit. To position a hole accurately, start the tool slowly and then increase the speed gradually.
- Page 10 Drilling in wood When drilling in wood, best results are obtained with wood drills equipped with a guide screw, The guide screw makes drilling easier by pulling the bit into the workpiece. Drilling in metal To prevent the bit from slipping when starting a hole, make an indentation with a center- punch and hammer the point to be drilled.
- Page 11 Dust cover Use the dust cover to prevent dust and dirt from falling over the floor when performing overhead drilling operations. Install the dust cover on the tool’s collar shown in the figures below. When installing to be completely installed on the tool’s collar. An incompletely installed dust cover will To remove the dust cover, slide push the dust cover firmly enough off firmly while turning...
-
Page 12: Maintenance
Always be sure that the tool attempting to perform inspection or maintenance. To maintain product SAFETY and RELlABl LITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. Recycling the Battery... - Page 13 ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only...
- Page 14 A p r . - l 4 - ' 9 2 CORDLESS HAMMER DRILL Model 8411D Note: The switch and other part configurations may differ from country to country.
- Page 15 MODEL 8411D ' ; i M DESCRIPTION MACHINE Keyless Chuck 1 0 Screw Pan Head M5x22 Splndle Woodrut1 Key 4 Steel Ball 4 8 Ball Bearing 6201DDW Flat Washer 12 Flat Washer 12 Gear 55 Spur Shifter Lever Switch Housing Set IWith Item 541...
- Page 16 Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective workmanship or material, Makita will repair (or at our option, replace) without charge.