Related Manuals for Makita 8413
Summary of Contents for Makita 8413
- Page 1 Cordless Percussion=Driver Drill INSTRUCTION MANUAL D W A Nt-Cd N I - M H ~ ~ H NI-MH Equipped with Electric Brake...
-
Page 2: Specifications
SPECIFICATIONS Concrete 13 mm 8413D ") No load speed (RPM) Model High 8413D 0-1'300 /min. o~,.,!,;~ 8433D 84431) Manufacturer reserves the right t o change specifications without notice Note Specifications differ from country to country WARNING For your personal safety, READ and understand before using SAVE THESE INSTRUCTIONS Steel Wood... -
Page 3: General Safety Rules
GENERAL SAFETY RULES (For All Battery Operated Tools) WARNING! Read and understand all instructions. to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS Work A r e a 1. Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. - Page 4 Tool U s e a n d C a r e Use clamps or other practical way t o secure and support the workpiece t o a stable platform. Holding the work by hand or against your body is unstable and may lead t o loss of control.
- Page 5 5. Keep hands away from rotating parts. 6. Do not leave the tool running. Operate the tool only w h e n hand-held. Do not touch the drill bit or the workpiece immediately after operation; they may be extremely hot and could burn your skin.
- Page 6 IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER & BATTERY CARTRIDGE SAVE THESE INSTRUCTIONS - This manual Length of Cord (Feet) AWG Size of Cord...
- Page 7 ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1 . Do not charge Battery Cartridge w h e n temperature is BELOW 10°C (5OOF) or ABOVE 4OoC (104OF). Do not attempt t o use a step-up transformer, an engine generator or DC power receptacle.
-
Page 8: Functional Description
You can recharge the battery cartridge fully after discharging it completely and recharging you or someone around you Battery cartridge DC1801 Charging light DC1801 is for charging Makita battery full charge This is a couple of times. normal condition and... - Page 9 If you charge a battery cartridge from a just-operated tool or been left in a location exposed to direct sunlight may flash in red color If this occurs, wait for a while Charging will begin after the battery cartridge cools The battery cartridge will cool faster from the high capacity battery charger If the charging light flashes alternately in green and red color, a problem exists and charg- ing is not possible The terminals on the charger or battery cartridge are clogged with...
- Page 10 Reversing switch action CAUTION *Always check the direction of rotation before operation *Use the reversing switch only after the tool comes to a complete stop Changing the direction of rotation before the tool stops may damage the tool *When not operating the tool, always set the reversing switch lever to the neutral posi- tion This tool has a reversing switch to change the direction...
- Page 11 Selecting the action mode This tool employs an action mode changing ring Select one the three modes suit- able for your work needs by using this ring For rotation only, turn the ring so that the arrow on the tool body points toward the anamark on the ring For rotation with hammering, turn the ring so that the arrow the +on...
- Page 12 ASSEMBLY Installing or removing driver bit or drill bit CAU TI Always be sure that the tool is switched off and the battery cartridge is removed before installing or removing the bit. Turn the sleeve counterclockwise the chuck jaws. Place the bit in the chuck as far as it will go.
-
Page 13: Operation
Adjustable depth rod The adjustable depth rod is used to drill holes of uniform depth Loosen the thumb screw, set to desired position, then tighten the thumb screw OPERATION Screwdriving operation First, turn the action mode changing ring so that the arrow on the tool body points to the c . - Page 14 Drilling operation First turn the action mode changing ring so that the arrow on the tool body points to the marking The adlusting ring can be aligned in any torque levels for this operation Then proceed as follows *Drilling in wood When drilling in wood best results are obtained with wood drills equipped with a guide screw The guide screw makes drilling easier by pulling the bit into the workpiece *Drilling in metal...
- Page 15 Blow-out bulb Use the blow-out bulb to clean out the hole Installing set plate 8413D Always install the set plate when using bat- tery cartridges 1200, 1202 or 1202A. Install the set plate on the tool with the screw provided.
-
Page 16: Maintenance
To maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts Recycling the Battery only way to dispose to recycle it. - Page 17 2" 2-5/16" 3-1/2" 2-1/2" 3-314" Foam polishing pad 2-3/4" 4" Part 4-1/4" 2-5/16" 3-3/16" 4-1/2" 3-7/16" 4-3/4" 3-5/8" 5" Makita tool specified in Shank diameter 3/16" 311 6" 114'' 114" 114" 114" 5/16" 1/4" 318" 1/4" 112" 318" 318" 5/8"...
- Page 18 Wool bonnet Part No. 743401-6 Battery cover Part No. 414938-7 High capacity battery charger Model DC1801 Battery cartridge 1222 Battery cartridge 1822 Plastic carrying case ‘Grip assembly Part No 122575-0 Depth rod Part No. 122576-8 High capacity battery charger Model DC1411 1234 1235 Battery cartridge 1422...
- Page 19 MAKITA L I M I T E D ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.