Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for HIKVISION DS-2CC11D3S-IR
Summary of Contents for HIKVISION DS-2CC11D3S-IR
- Page 1 ‘ Camera HD-SDI Camera User Manual UD.6L0201D1078A01...
- Page 2 Thank you for purchasing our product. If there are any questions, or requests, please do not hesitate to contact the dealer. This manual applies to DS-2CC11D3S-IR, DS-2CC51D3S-VPIR. This manual may contain several technical incorrect places or printing errors, and the content is subject to change without notice. The updates will be added to the new version of this manual.
-
Page 3: Regulatory Information
HD-SDI Camera·User Manual Regulatory Information FCC Information FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. -
Page 4: Safety Instruction
HD-SDI Camera·User Manual equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info. 2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. - Page 5 HD-SDI Camera·User Manual Warnings In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region. Please refer to technical specifications for detailed information. Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source with AC 24V or DC 12V according to the IEC60950-1 standard.
- Page 6 HD-SDI Camera·User Manual Do not touch senor modules with fingers. If cleaning is necessary, use clean cloth with a bit of ethanol and wipe it gently. If the camera will not be used for an extended period, please replace the lens cap to protect the sensor from dirt.
-
Page 7: Table Of Contents
HD-SDI Camera·User Manual Table of Contents 1 Introduction ...................... 9 1.1 Product Features ................9 1.2 Overview ..................10 2 Installation ...................... 12 2.1 Installation of HD-SDI Bullet Camera..........12 2.2 Installation of HD-SDI Dome Camera ..........14 3 Menu Description ................... 18 3.1 LENS .................... - Page 8 HD-SDI Camera·User Manual 3.5.8 Version ................35 3.6 ADJUST ................... 36 3.6.1 Sharpness ................36 3.6.2 Monitor ................37 3.6.3 OSD ..................39 3.6.4 LSC ..................39 3.6.5 NTSC/PAL ................39 3.7 RESET ..................... 40 3.8 EXIT ....................40...
-
Page 9: Introduction
HD-SDI Camera·User Manual 1 Introduction 1.1 Product Features This series of camera adopts high-sensitive sensor and advanced circuit board design technology. It features high resolution, low distortion, and low noise features, etc., which make it extremely suitable for surveillance system and image process system. -
Page 10: Overview
HD-SDI Camera·User Manual 1.2 Overview Figure 1-1 Overview of HD-SDI Bullet Camera Table 1-1 Description Description Description Mounting Base OK Button Adjustable Nut SDI Cable Sun Shield Power Cable Lens Auxiliary Video Output IR LED RS485 Cable... - Page 11 HD-SDI Camera·User Manual Figure 1-2 Overview of HD-SDI Dome Camera Table 1-2 Description Description Description Mounting Base OK Button Black Liner SDI Cable Lower Dome Power Cable IR LED Auxiliary Video Output Lens RS485 Cable...
-
Page 12: Installation
HD-SDI Camera·User Manual 2 Installation Before you start: Please make sure that the device in the package is in good condition and all the assembly parts are included. Make sure that all the related equipment is power-off during the installation. ... - Page 13 HD-SDI Camera·User Manual φ4 φ Cutting line φ68 Screw Hole Template Figure 2-1 Drill Template 2. Route the corresponding cables. 3. Fix the camera to the wall with the supplied P A4 screws. Figure 2-2 Secure the Camera to the Wall...
-
Page 14: Installation Of Hd-Sdi Dome Camera
HD-SDI Camera·User Manual 4. Connect the video output cable to the monitor. Connect the power cable to the power supply. 5. Adjust the Lens 1). Loosen the adjustable nut. 2). Adjust the camera from pan direction which is 0~360°adjustable. 3). Adjust the camera from tilt direction which is 0~90°adjustable. 4). - Page 15 HD-SDI Camera·User Manual Hole Ceiling Mounting Hole Hole Figure 2-4 Drill Template Loosen the set screws with a hex key (supplied) to remove the lower dome. Figure 2-5 Remove the Lower Dome...
- Page 16 HD-SDI Camera·User Manual Fix the mounting base on the ceiling with screws. Figure 2-6 Fix the Mounting Base Note: If required, you can route cables through the side opening on the side of the mounting base. Side Opening Figure 2-7 Side Opening Loosen the tilt lock screws, adjust the tilting position in a range of 65 degrees, and tighten the tilt lock screws.
- Page 17 HD-SDI Camera·User Manual Rotate the black liner to adjust the panning position in a range of 180 degrees until you get the desired surveillance angle. Tilt Lock Screw Black Liner TILT Figure 2-8 Angle Adjustment Note: As the lens has already been factory adjusted to the best imaging effect, you just need to adjust the panning position and tilting position to get the desired surveillance angle.
-
Page 18: Menu Description
HD-SDI Camera·User Manual 3 Menu Description Figure 3-1 Main Menu Overview Notes: The OK button on the cable is used to control the menu. Press the OK button up/down to select the menu item. Press the OK button left/right to adjust the value. ... -
Page 19: Exposure
HD-SDI Camera·User Manual 3.2 EXPOSURE EXPOSURE SHUTTER AUTO SENS-UP BRIGHTNESS ---|------ 40 ACCE DEFOG BACKLIGHT RETURN Figure 3-2 Exposure Exposure describes the brightness-related parameters. You can adjust the image brightness by the SHUTTER, AGC, SENS-UP, BRIGHTNESS, ACCE, BACKLIGHT, etc. in different light conditions. 3.2.1 Shutter Shutter denotes the speed of the shutter. -
Page 20: Agc
HD-SDI Camera·User Manual 3.2.2 AGC It’s a form of amplification where the camera will automatically boost the image received in much lower light conditions than standard in order to optimize the clarity of image in poor light scene. OFF, LOW, MIDDLE, and HIGH are selectable for the AGC value. -
Page 21: Defog
HD-SDI Camera·User Manual 3.2.6 Defog DEFOG is used in special environment such as fog or rain or in high illumination, which have lower dynamic range than ordinary environment. OFF, LOW, MIDDLE, and HIGH are selectable. 3.2.7 Backlight You can set the Backlight to OFF, BLC, and HSBLC. Backlight Compensation (BLC) If there’s a strong backlight, the object in front of the backlight will appear silhouetted or dark. - Page 22 HD-SDI Camera·User Manual 3. Press the OK button up/down/left/right to define the BLC size. 4. Press OK to confirm the selection. ↑ ← POSITION→ ↓ Figure 3-4 Define a BLC Area HSBLC HSBLC SELECT AREA 1 ON DISPLAY LEVEL ---|------ 40 MODE ALL DAY...
- Page 23 HD-SDI Camera·User Manual 1. Select HSBLC by setting the OK button to left/right, and press OK to enter the edit interface. 2. Move the cursor to SELECT and select the area by pressing the OK button to left/right. Four areas are selectable. 3.
-
Page 24: White Balance (Wb)
HD-SDI Camera·User Manual 3.2.8 White Balance (WB) White balance is the white rendition function of the camera to adjust the color temperature according to the environment. It can remove the unrealistic color casts in the image INDOOR, OUTDOOR, MANUAL, ATW (Auto-tracking White Balance), AWC→SET are selectable. -
Page 25: Day & Night
HD-SDI Camera·User Manual ATW mode means the white balance is continuously being adjusted in real-time according to the color temperature of the scene illumination. AWC→SET The camera will adjust the white balance according to a certain environment. If the environment is changed, you need to use AWC→SET to adjust the color temperature again. - Page 26 HD-SDI Camera·User Manual 3.4 NR NR (Noise Reduction) is used to reduce the noise in the video stream. Move the cursor to NR, and press confirm to enter the NR submenu 2D&3D NR 2DNR 3DNR LEVEL ---|------ 50 SMART NR RETURN Figure 3-7 ...
-
Page 27: Special
HD-SDI Camera·User Manual 3D NR S-LEVEL |--------- 0 E-LEVEL |--------- 0 RETURN Figure 3-8 3D NR The NR Level ranges from 0 to 100. SMART NR Smart NR usually takes effect in cooperation with 3D NR. You can set it to ON to improve the image fluency. -
Page 28: Camera Title
HD-SDI Camera·User Manual SPECIAL CAM TITLE D-DFFECT MOTION PRIVACY LANGUAGE DEFECT RS485 VERSION 121005 RETURN Figure 3-9 Special 3.5.1 Camera Title You can name your camera by configuring the CAM TITLE. Move the cursor to CAM TITLE, set it to ON, and press OK button to enter the edit interface. -
Page 29: D-Effect
HD-SDI Camera·User Manual 1. Move the cursor to ←or →, and press OK button to decide the character position on the dotted line. 2. Move the cursor to select the needed characters, numbers, and symbols. 3. Press OK button to confirm. The selected character will be displayed on the dotted line below. -
Page 30: Motion
HD-SDI Camera·User Manual FREEZE You can set the freeze function as ON or OFF. When you set it as on, the image is frozen as still. The live view will stay on the moment you set the freeze ON. Note: The mirror function will be disabled if the FREEZE is ON. - Page 31 HD-SDI Camera·User Manual MOTION SELECT AREA 1 DISPLAY ON SENSITIVITY ----|---- 30 MOTION VIEW DEFAULT RETURN Figure 3-12 Motion Detection Set a Motion Detection Area: Steps: 1. Move the cursor to DISPLAY, and press OK button to enter the motion detection edit interface.
-
Page 32: Privacy
HD-SDI Camera·User Manual DISPLAY Display the selected motion area or not. SENSITIVITY The sensitivity of the motion detection. The sensitivity value ranges from 0 to 60, and the higher the sensitivity causes the better response of the detection. ... -
Page 33: Language
HD-SDI Camera·User Manual Set a Privacy Area: Steps: 1. Move the cursor to DISPLAY, and press OK button to enter the privacy mask edit interface. 2. Press the OK button to up/down/left/right to define the position of the selected privacy mask area. 3. -
Page 34: Defect
HD-SDI Camera·User Manual 3.5.6 Defect DEFECT LIVE DPC LEVEL ---|-----30 STATIC DPC START LEVEL ---|-----25 SENS-UP RETURN Figure 3-14 Dead Pixel Correction LIVE DPC You can choose ON, OFF and AUTO. If auto is selected, the level is not configurable. -
Page 35: Rs485
HD-SDI Camera·User Manual SENS-UP Adjust the sensor. X2, X4, X6, X8, X10, X15, X20, X30, and X60 are selectable. 3.5.7 RS485 If you want to configure the menu items remotely, you have to set the RS485 parameters of control device the same as those of camera. RS485 CAM ID ID DISPLAY... -
Page 36: Adjust
HD-SDI Camera·User Manual 3.6 ADJUST In the Adjust sub-menu, you can set the sharpness, the image quality on monitor, the OSD settings, the Lens Shadow Compensation, and the Video output standard. ADJUST SHARPNESS MONITOR LCD NTSC/PAL RETURN Figure 3-16 Adjust 3.6.1 Sharpness SHARPNESS... -
Page 37: Monitor
HD-SDI Camera·User Manual Sharpness determines the amount of detail an imaging system can reproduce. You can set the sharpness as ON and OFF, when sharpness is on, the images appears clearer and sharper. LEVEL The sharpness level is between 0 and 100. ... - Page 38 HD-SDI Camera·User Manual RED GAIN 0 to 100 are selectable. MONITOR LCD USER 1 GAMMA ----|----50 BLUE GAIN ----|----50 RED GAIN RETURN Figure 3-19 Monitor LCD GAMMA Gamma is the name of a nonlinear operation used to code and decode luminance or tristimulus values in video or still image system 1.00, 0.95, 0.90, 0.85, 0.80, 0.75, 0.70, 0.65, 0.60, 0.55, 0.50, 0.45, USER1, USER2, and AUTO are selectable.
-
Page 39: Osd
HD-SDI Camera·User Manual 3.6.3 OSD TEXT COLOR OUTLINE RETURN Figure 3-20 OSD Configuration TEXT COLOR There are 8 colors configurable for the OSD menu. Press the OK button to Left or right to change the color of the OSD. ... -
Page 40: Reset
HD-SDI Camera·User Manual NTSC, short for the National Television System Committee, is the analog television system that is used in most of North America, parts of South America Myanmar, South Korea, etc. 3.7 RESET Reset all the settings to the factory default. 3.8 EXIT Move the cursor to EXIT and click OK button to exit from the menu... - Page 41 HD-SDI Camera·User Manual...