High-definition IR Water-proof Bullet Camera User Manual UD.6L0201D0086A01...
Page 2
High-definition IR Water-proof Bullet Camera· User Manual Thank you for purchasing our product. If there are any questions, or requests, please do not hesitate to contact the dealer. This manual applies to DS-2CE1582P (N)-VFIR3 DS-2CC1283P-VFIR3 DS-2CC1283P-AVFIR3 DS-2CC1281P (N)-VFIR3 DS-2CC1281P (N)-AVFIR3 DS-2CC12A1P (N)-VFIR3 DS-2CC12A1P (N)-AVFIR3 This manual may contain several technical incorrect places or...
High-definition IR Water-proof Bullet Camera· User Manual Regulatory Information FCC Information FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Page 4
High-definition IR Water-proof Bullet Camera· User Manual 2002/96/EC (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points.
High-definition IR Water-proof Bullet Camera· User Manual 1 Introduction 1.1 Product Features This camera adopts a high-sensitivity sensor and advanced circuit design technology. It possesses features of high resolution, low image distortion and low noise, which are suitable for surveillance system and image processing system.
High-definition IR Water-proof Bullet Camera· User Manual 2 Installation Before you start: Read the following contents carefully before the installation. Make sure that all the related equipment is power-off during the installation. Check the specification of the products for the installation ...
Page 10
High-definition IR Water-proof Bullet Camera· User Manual Before any operation, please make sure that the device in the package is in good condition and all the assembly parts are completed. Steps: 1. Drill the holes on the wall with the supplied drilling template. 2.
Page 11
High-definition IR Water-proof Bullet Camera· User Manual Note: You must loosen the lock screw or fixed ring before adjustment and tighten it when you adjusted it. 2). Rotate the panning table to adjust the panning position of the camera. The adjustable range is from 0 degree to 360 degrees.
Page 12
High-definition IR Water-proof Bullet Camera· User Manual Zoom Focus Figure 2-3 Adjust the Lens...
High-definition IR Water-proof Bullet Camera· User Manual 2.2 Power Supply Figure 2-4 Power Cable (Round Interface) Note: Please make sure the power adapter is match with the camera, the standard adapter model for camera is DC12V (Please refer to technical specifications for more details).
Page 14
High-definition IR Water-proof Bullet Camera· User Manual Figure 2-5 Power Cable (Two-needle Interface ) Note: Please make sure that the power adapter is match with the camera. The standard power supply of the camera is usually 12V DC or 24V AC (Please refer to technical specifications for more details).
High-definition IR Water-proof Bullet Camera· User Manual 3 Menu Description (A) Note: This Menu only works for DS-2CC1283P-VFIR3, and DS-2CC1283P-AVFIR3. 3.1 Menu Overview This series of camera supports OSD menu, the main menu is listed as below: Table 3-1 Main Menu EXPOSURE LENS, HBLC/D-WDR, AGC, 3D-DNR, SENSE UP...
High-definition IR Water-proof Bullet Camera· User Manual 3.2 Exposure Purpose: Exposure is realized by Shutter/IRS/Gain control. On the Exposure menu, you can configure the LENS, HBLC/D-WDR, AGC, 3D DNR, SENSE-UP settings. See Figure 3-1. EXPOSURE LENS ELC HBLC/D-WDR BLC HIGH 3D DNR AUTO SENSE-UP...
Page 17
High-definition IR Water-proof Bullet Camera· User Manual the value from 1 to 100. 50 is the default value. See Figure 3-2. LENS-ELC E.SHUTTER AUTO BRIGHT 028 ---|---- RETURN↓ Figure 3-2 ELC Mode DC Mode In DC Mode, auto iris has a higher priority to auto shutter. AUTO, x2, x4, x8, x16, x32, x64, x128, x256, x512, x1024,1/50, 1/100, 1/120FLK, 1/250, 1/500, 1/1K, 1/2K, 1/4K,1/10K,1/100K (second) are selectable for...
Page 18
High-definition IR Water-proof Bullet Camera· User Manual LENS-DC E.SHUTTER AUTO BRIGHT 028---|----- DC REF 010---|----- RETURN↓ Figure 3-3 DC Mode HBLC/D-WDR Note: This item contains BLC, HLI, and D-WDR function. BLC (Backlight Compensation) If there’s a strong backlight, the object in the foreground appears silhouetted or dark.
Page 19
High-definition IR Water-proof Bullet Camera· User Manual BLC MODE MANUAL BLC WEIGHT RETURN ↓ Figure 3-4 BLC BLC-MANUAL 006--|------- BOTTOM 012----|----- LEFT 004-|-------- RIGHT 011---|------ RETURN↓ Figure 3-5 BLC Area Set HLI (Highlight Inverse) Highlight inverse is a function which inverses the area which is strongly- highlighted.
Page 20
High-definition IR Water-proof Bullet Camera· User Manual HBLC BLC LEVEL 006 --|-------- BUTTOM 012---|-------- LEFT 004--|-------- RIGHT 011---|-------- RETURN ↓ Figure 3-6 HBLC Mode ALL DAY and NIGHT are selectable. All day means HLI function will be effective for both day and night, and Night means it only takes effect in night mode.
Page 21
High-definition IR Water-proof Bullet Camera· User Manual HBLC MODE NIGHT SET LEVEL 255---------| GRAY MODE BLACK MASK SEL MASK1 RETURN ↓ Figure 3-7 HLI Mask Sel Mask Sel is for configuring some areas which you don’t want to be inversed. You can select four areas in all and define the size of the mask by changing the value for its top, bottom, left and right.
Page 22
High-definition IR Water-proof Bullet Camera· User Manual You can set the D-WDR LEVEL from 0 to 20. The bigger the value is, the higher the D-WDR intensity is. AGC (Auto Gain Control) AGC is a control circuit that automatically changes the gain of a receiver or other piece of equipment to maintain the output video quality.
High-definition IR Water-proof Bullet Camera· User Manual 3.3 Color Purpose: You can configure the WB MODE, R-Y GAIN, B-Y Gain functions from Color menu. See Figure 3-9. COLOR WB MODE R-Y GAIN 128---|------- B-Y GAIN 128---|------- EXIT RETURN↓ Figure 3-9 Color Menu WB MODE (White Balance Mode) ...
High-definition IR Water-proof Bullet Camera· User Manual AWC>PUSH: White balance is continuously being adjusted in real-time according to the color temperature of the scene illumination in AWC>PUSH mode. Manual: Change the Red value and the Blue value to manually set the white balance. Set the WB Mode to Manual, and then enter the Manual Menu to set the value for M.WB R and M.WB B, see Figure 3-10.
Page 25
High-definition IR Water-proof Bullet Camera· User Manual You can configure the parameters for D&N MODE, C_SUP, and A_SUP function from Day & Night Menu. See Figure 3-11. DAY & NIGHT D&N MODE AUTO C_SUP 030---|------- A_SUP 051---|------- EXIT RETURN↓ Figure 3-11 Color Menu D&N MODE ...
Page 26
High-definition IR Water-proof Bullet Camera· User Manual DWELL TIME: It’s the duration when the day/night mode switches to night/day mode, and the default value is 3s. You can set it from 0 to 15s. See Figure 3-12. D&N-AUTO BURST DAY>NIGHT 19--|------ NIGHT>DAY 18--|------...
High-definition IR Water-proof Bullet Camera· User Manual EX-CDS BURST DAY>NIGHT 151---|----- NIGHT>DAY 100---|------ SMART IR AUTO DWELL TIME 003---|----- RETURN↓ Figure 3-13 EX-CDS Note: D&N will not be triggered by the external CDS since this series of cameras do not have alarm output, while the SMART IR function is still configurable from here.
Page 28
High-definition IR Water-proof Bullet Camera· User Manual FUNCTION MIRROR SHARPNESS 016---|---- MONITOR MODE 1 GAMMA 0.45 EXIT RETURN↓ Figure 3-14 Function Menu Mirror You can turn the Mirror ON or OFF. Turning on the Mirror function can flip the displayed image 180 degrees horizontally, shown as the mirror reflection of the image.
High-definition IR Water-proof Bullet Camera· User Manual LSC(Lens Shading Compensation) LSC is used for the complement the quality of the lens. It’s a function which increases gain of screen angle. You can turn the LSC to ON or OFF. 3.6 Motion Purpose: You can configure Motion, Area Select, Sensitivity, Display, Hold...
Page 30
High-definition IR Water-proof Bullet Camera· User Manual ON or OFF. You can define the Area size by selecting the different value for TOP, BUTTON, LEFT, and RIGHT. See Figure 3-16 and Figure 3-17. MOT-AREA AREA 1 ON AREA 2 ON AREA 3 ON...
High-definition IR Water-proof Bullet Camera· User Manual DISPLAY You can set the Display to OFF, ICON, or TRACE. Icon means it w ill be displayed as an icon when the motion detection occurs, and it w ill be displayed as mosaic if you select trace.
Page 32
High-definition IR Water-proof Bullet Camera· User Manual If you don’t want some parts of the area to be viewed or recorded, then the Privacy Mask will be useful here. You can set 8 privacy masks in all. Steps: 1. Enter the privacy configuration interface by pressing the up/down button.
Page 33
High-definition IR Water-proof Bullet Camera· User Manual MASK 1 L_TOP MOVE XY COLOR SET BLACK RETURN↓ Figure 3-19 Privacy Mask Setup DOT SEL Select L_BOT, L_TOP, R_BOT, R_TOP from DOT SEL to decide which corner you will use to change the mask size and position.
High-definition IR Water-proof Bullet Camera· User Manual Select the color for the privacy mask. Blue, Magenta, Cyan, Gray, Black, White, Red, Green are selectable. 3. Click Return to save the settings and go back to the previous page. 3.8 Setup Purpose: You can configure the TITLE, MANUAL DPC, AUTO DPC, OLPF, and OSD COLOR from SETUP menu.
Page 35
High-definition IR Water-proof Bullet Camera· User Manual selecting Title On, you are able to write TEXT to display on the screen. It supports at maximum of 16 characters input. ← → are used for moving the cursor to the exact position where the title should be edited or modified.
Page 36
High-definition IR Water-proof Bullet Camera· User Manual The camera supports Dead Pixels Compensation function. It will correct the defective pixels which are not performed as expected. You can set the Manual DPC to Manual or OFF, and if you select Manual for it, then you can enter the parameter interface to configure the parameters for White Thr (range from 0 to 255), Black Thr (range from 0 to 255), and DPC Level (range from 0 to 255).
High-definition IR Water-proof Bullet Camera· User Manual 3.9 System Purpose: You can set the Camera ID, Communication, and Language from this System menu. See Figure 3-22. SYSTEM CAMERA ID 008--|------- COMMUNI. LANGUAGE ENGLISH EXIT RETURN ↓ Figure 3-22 System Menu Camera ID ...
High-definition IR Water-proof Bullet Camera· User Manual 3.10 Exit Purpose: You can save your settings and exit. And you can also restore all the parameters back to the Factory Settings. See Figure 3-23. EXIT FACTORY SET SAVE & EXIT↓ EXIT↓ Figure 3-23 Exit Menu Factory Set: YES or No are selectable.
High-definition IR Water-proof Bullet Camera· User Manual 4 Menu Description (B) Note: This Menu works for DS-2CC1281P (N)-VFIR3, DS-2CC1281P (N)-AVFIR3, DS-2CC12A1P (N)-VFIR3, DS-2CC12A1P (N)-AVFIR3. 4.1 Main Menu Steps: 1. Press the menu button on the rear panel of the camera to access the main menu and the submenu.
High-definition IR Water-proof Bullet Camera· User Manual AREA, AREA SEL PRIVACY AREA SEL, COLOR, TRANSP, MOSAIC DAY/NIGHT AUTO, COLOR, B/W Y LEVEL CAMERA ID SYNC INT , LINELOCK LANGUAGE English/Chinese/Japanese/French/Russian/ Portuguese/ Spanish/ German CAMERA RESET EXIT/SAVE ALL 4.2 Lens Settings Purpose: On LENS settings menu and SHUTTER/AGC settings menu, you can set the value of iris, shutter speed and AGC (Auto Gain Control)
Page 41
High-definition IR Water-proof Bullet Camera· User Manual Move the cursor to LENS, and you can switch the menu button left/right to select MANUAL or AUTO. Press the menu button to access the manual/auto interface. In MANUAL mode, you have to set the LENS IRIS value ...
High-definition IR Water-proof Bullet Camera· User Manual SPEED Adjust the auto iris speed. You can set the auto iris speed from 0 to 255 (speed from lowest to highest). Note: It is suggested to adjust the auto iris speed only when the iris is not functioning properly, e.g., when the iris is keeping on enlarging or reducing.
Page 43
High-definition IR Water-proof Bullet Camera· User Manual SHUTTER Manually set the shutter speed. For PAL standard, 1/50, 1/120, 1/250, 1/500, 1/1K, 1/2K, 1/4K and 1/10K (second) are selectable. For NTSC standard, 1/60, 1/100, 1/250, 1/500, 1/1K, 1/2K, 1/4K and 1/10K (second) are selectable.
High-definition IR Water-proof Bullet Camera· User Manual HIGH LUMINANCE MODE When LENS type is AUTO IRIS, you can choose SHUT+AUTO IRIS mode or AUTO IRIS mode; When LENS type is Manual, only SHUT mode is available. BRIGHTNESS Set the desired BRIGHTNESS value which the iris and shutter speed will adjust automatically for.
Page 45
High-definition IR Water-proof Bullet Camera· User Manual ATW, PUSH, PUSH LOCK, USER1, USER2, ANTI CR and MANUAL modes are selectable. You can switch the menu button left/right to choose the mode. PUSH In the PUSH mode, the viewed image retains color balance automatically according to the color temperature.
Page 46
High-definition IR Water-proof Bullet Camera· User Manual B-GAIN Adjust the blue gain. The B-GAIN value ranges from 0 to 255. R-GAIN Adjust the red gain. The R-GAIN value ranges from 0 to 255. USER 2 This mode is suitable for environments with fluorescent light. B-GAIN The B-GAIN value ranges from 0 to 255.
Page 47
High-definition IR Water-proof Bullet Camera· User Manual In ATW mode, white balance is continuously being adjusted in real-time according to the color temperature of the scene illumination. SPEED ------|--239 DELAY CNT --|------016 ATW FRAME *1.00 ENVIRONMENT INDOOR RETURN Figure 4-6 ATW SPEED The SPEED can be set from 0 to 255.
High-definition IR Water-proof Bullet Camera· User Manual 4.5 Backlight Settings Purpose: You can set the backlight compensation and high light compensation functions of the camera on BACKLIGHT settings submenu. There are OFF, BLC and HLC modes selectable. Switch the menu button left/right to choose the mode.
Page 49
High-definition IR Water-proof Bullet Camera· User Manual PICT ADJUST MIRROR BRIGHTNESS |-------- 000 CONTRAST ----|---- 128 SHARPNESS ----|---- 128 ----|---- 128 GAIN ----|---- 128 RETURN↓ Figure 4-7 Picture Adjust MIRROR If you turn the MIRROR function on, the image w ill be flipped horizontally, shown as the mirror reflection of the image.
High-definition IR Water-proof Bullet Camera· User Manual You can adjust the value of this feature to change the color tone of the image. The value ranges from 0 to 255. GAIN You can adjust the value of this feature to change the color gradation.
High-definition IR Water-proof Bullet Camera· User Manual LUMINANCE There are MID, HIGH and LOW selectable, standing for middle, high and low luminance respectively. CONTRAST There are MID, HIGH, LOW, MIDLOW and MIDHIGH selectable. 4.8 Motion Detection Settings Before you start: There are two parts of MOTION DET configurations, BLOCK DISP and MONITOR AREA.
Page 52
High-definition IR Water-proof Bullet Camera· User Manual 1. Move the cursor to MOTION DET, and switch it to ON and press the menu button to enter the submenu. 2. Position the cursor on DETECT SENSE, and switch the menu button left/right to adjust the sensitivity level. 3.
High-definition IR Water-proof Bullet Camera· User Manual 4. Position the cursor on AREA SEL. You can set 4 separate monitor areas at a time. 5. Select one of the monitor areas and set the values of TOP, BOTTOM, LEFT and RIGHT to define its size and position. You can see the frame of the area shown on the screen while defining the values.
High-definition IR Water-proof Bullet Camera· User Manual 5. Repeat steps 1-4 to configure more privacy masks. Note: You can set up to 8 privacy masks; only 4 masks can be configured when motion detection function is on. PRIVACY AREA SEL ----|---- 128 BUTTOM ----|---- 128...
Page 55
High-definition IR Water-proof Bullet Camera· User Manual COLOR Color mode is used for normal lighting conditions. B/W mode can increase the sensitivity in low light ing conditions. On the B/W submenu, you can switch it to ON or OFF to enable or disable BURST.
Page 56
High-definition IR Water-proof Bullet Camera· User Manual DAY/NIGHT BURST DELAY CNT |-------- 000 DAY→NIGHT -|------- 003 NIGHT→DAY -|------- 005 RETURN Figure 4-12 Day/Night BURST Switch ON or OFF to enable or disable signal synchronization. DELAYCNT Set the delay time before the day/night modes switch.
High-definition IR Water-proof Bullet Camera· User Manual EXIT1/EXT2 mode enables synchronization of day/night and IR light. 4.11 NR Settings Purpose: Noise Reduction is used to reduce the noises in the video signal. Move the cursor to NR, press the menu button to enter the NR submenu.
Page 58
High-definition IR Water-proof Bullet Camera· User Manual Switch the menu button to set it to ON and press the menu button to enter the submenu. CAMERA ID ABCDEFGHIJKLMNOPQRSTUV WXYZ0123456789-!”#$%&’ ()_ , ¥:;<= >?@\^*.x+/ CHR 1 CHR 2 ← → ↑ ↓ CLR POS RETURN...
High-definition IR Water-proof Bullet Camera· User Manual 1. Position the cursor on one of the arrows. 2. Press the menu button to position the cursor on the character of the current camera ID which needs to modify. 3. Move the cursor to the character list and select one to replace Clearing the camera ID Steps: 1.
High-definition IR Water-proof Bullet Camera· User Manual 3. Press the menu button to enter the menu and you can see the SYNC mode is switched from INT to LINELOCK or vice versa. Note: For line lock synchronization, you can adjust the V Phase value to adjust the power synchronous phase.
High-definition IR Water-proof Bullet Camera· User Manual 1. Exit the OSD menu to the live view screen. 2. Switch and hold the menu button to the left for 2 seconds until you see the message of “COVER-UP LENS/CLOSE IRIS”. 3. Cover the lens or close the iris to prevent the light from entering the lens.