Sony BVP-900 Series Product Information Manual page 59

1) Up tally lamp
Illuminates when the camera receives a red tally signal. When the
CALL button on an MSU-700 Master Set-up Unit or RCP-700 Series
Remote Control Panel is pressed, and with the CCU CALL switch on
the internal MS board set to ON, the lamp illuminates if not already
lit, and is turned off if it was illuminated. The brightness of the lamp
is adjustable by a control on the internal MS board. To stop the lamp
illuminating, set the UP TALLY switch on the rear panel to OFF.
Attach one of the supplied number plates (0 through 9) to show the
camera number. For details on adjusting the lamp brightness and
attaching the number plate, refer to the system manual.
2) Safety catch
Safety catch to prevent the side panel from accidentally opening. To
open the side panel, loosen the side-panel lock screw, slide the safety
catch toward the lens, and open the panel. The side panel
automatically locks as it is closed. For details, refer to the system
manual.
3) Camera number plate
Attach the supplied light gray number plate to show the camera
number. For details how to attach a number plate, refer to the system
manual.
4) Side-panel lock screw
Locks the side panel to prevent it from accidentally opening. Turn it
fully clockwise.
5) Lens lock and knob
Locks the lens. To attach or detach the lens, turn the knob fully
counterclockwise until the lever is horizontal. To lock the lens, turn
the knob clockwise until the lever is vertical.
6) Cable clamp
Retains the triax camera cable, accepting cables from 8 to 15 mm in
diameter. For details on how to use the cable clamp, refer to the
system manual.
7) AUDIO IN CH-1 and CH-2 (audio input channels 1 and 2)
connectors (XLR 3-pin)
Accept microphone or line level signals.
8) AUDIO IN (audio input select) selectors
Set to the appropriate positions for the equipment connected to the
AUDIO IN CH-1 and CH-2 connectors.
MIC: When a microphones is connected.
LINE: When a line-level signal source is connected.
9) Microphone power switches
Control power fed to microphones connected to the AUDIO IN CH-1
and CH-2 connectors.
+48 V: When the connected microphone requires an external
power source, a +48 V supply is fed to the microphone.
OFF: When the connected microphone does not require
external power.
10) PROMPTER (teleprompter) connector (BNC type)
The signal input to the PROMPTER INPUT connector on a CCU-
700A/700AP is output from this connector to feed a teleprompter
monitor.
11) TEST OUT (test signal output) connector (BNC type)
Outputs the signal selected with the video signal select buttons on
the rear panel, when the TEST OUT switch on the MS board is set to
VF. When the TEST OUT switch is set to RET, the return video
signal is output. (The return video signal selected last is output.)
When a BKP-7910/7910P Stand-alone Kit is installed in the camera, a
Location and Function of Parts and Controls
composite video signal is output if the TEST OUT switch is set to
VBS.
12) TRACKER connector (10-pin)
Used for communication between the camera operator and tracker
and for intercom 1 and 2 connection. It also supplies the up tally and
program audio signals.
13) RET CONTROL (return video control) connector (6-pin)
Used for selecting the return video signal, 1, 2, 3 or 4 and for turning
the intercom microphone on or off from external equipment such as
a selector unit on the camera pan bar.
14) SCRIPT (script light) connector (4-pin)
Supplies power (12 V/5 W maximum) for the script light.
15) REMOTE connector (8-pin)
Interface for an optional Master Set-up Unit or Remote Control
Unit/Panel, via a CCA cable.
16) Accessory bracket
Used to attach an optional accessory, such as a BKP-7911/7912
Script Holder or a lens focus/zoom demand control. To attach an
accessory, refer to the its instruction manual.
17) AC OUT (AC power output) connector
Supplies AC power (200 VA maximum).
18) CCU (camera control unit) connector (triax connector)
Interface for the triax cable connecting the camera to the Camera
Control Unit. All the signals to and from a BVP-900 Series camera
and its CCU (power, control, video and audio) are carried by this
single triax cable.
19) REF IN (reference signal input) connector (BNC type)
Accepts a VBS or black burst signal to genlock the camera when it is
operating in stand-alone mode.
20) VBS (video signal output) connector (BNC type)
Supplies composite video signals when the BVP-900/900P is
operating in stand-alone mode.
*1
21 )VTR connector (26-pin)
Connection for a VTR, via a CCZ or CCZQ cable, when the camera is
operating in stand-alone mode.
22) DC IN (DC power input) connector (4-pin)
Power connection for an external DC power source (11.5 V to 18 V)
when using a BVP-900/900P as a stand-alone camera.
*1. These connectors are part of the BKP-7910/7910P Stand-alone Kit.
*1
10
*1
*1
58