Sony BVP-900 Series Product Information Manual page 118

10
Location and Function of Parts and Controls
Detail Menu
Category Subcategory
Mode Set —
Gain SW —
SW Setup —
VR Setup Knee
M Gamma
Detail
White
Black
117
Item Setting
Act Md2, Md3
FltMax 4, 5
L (RM) [-3, 0, 3, 6, 9, 12, 15, 18, .....42
M (RM) [-3, 0, 3, 6, 9, 12, 15, 18, .....42
H (RM) [-3, 0, 3, 6, 9, 12, 15, 18, .....42
Mode RM, CAM
AtKnee AtKnee, KneeSat
BikGamma, SkinDtl
Test 1, 2, 3
Item Knee, Slope, Knee Sat,
M-VHS, M Gamma,
BikGamma, Detail,
SkinDtl
Ctrl Rel, Abs
Scal 1/1, 1/2, 1/4
Item Knee, Slope, Knee Sat,
M-VHS, M Gamma,
BikGamma, Detail,
SkinDtl
Ctrl Rel, Abs
Scal 1/1, 1/2, 1/4
Item Knee, Slope, Knee Sat,
M-VHS, M Gamma,
BikGamma, Detail,
SkinDtl
Ctrl Rel, Abs
Scal 1/1, 1/2, 1/4
Ctrl Rel, Abs
Scal 1/1, 1/2, 1/4
Item Black, Flare
Ctrl Rel, Abs
Scal 1/1, 1/2, 1/4
(An Underlined item under 'Setting' indicates the factory setting.)
Contents
Selects the control mode.
Md2: Each time the ACTIVE button is pressed, FULL and LOCK are toggled.
Md3: Each time the ACTIVE button is pressed, FULL,
PART and LOCK are cyclically switched.
Sets the default numbers of the ND and CC filters.
However, when the connected camera has an automatic filter detection facility,
setting this item is not required.
Selects the gain value for GAIN selector position LOW in Gain Local mode (in 3 dB
steps to 42 dB max.) *1
Selects the gain value for GAIN selector position MID in Gain Local mode (in 3 dB
steps to 42 dB max).*1
Selects the gain value for GAIN selector position HIGH in Gain Local mode (in 3 dB
steps to 42 dB max.) *1
Selects the Gain Local/Remote mode.
RM: Gain Local mode (The gain is controlled according to the settings on this unit
regardless of the GAIN L/M/H settings on the camera.)
CAM: Gain Remote mode (The gain is controlled according to the GAIN L/M/H
settings on the camera. Effective only with a camera equipped with an
automatic detection facility.)
Selects the function of the AUTO KNEE button.
AtKnee: Turns the Auto Knee saturation function on and off (on when lit).
KneeSat: Turns the Knee function on and off (on when lit).
BlkGamma: Turns the Black Gamma function on and off (on SkinDtl: Turns the Skin
detail function on and off (on when lit).
Selects the output signal when the OUTPUT selector is set
to the TEST position.
1: Gamma-waveform signal
2: Three-value staircase signal
3: Ten-value staircase signal
Item: Selects the function of the control knobs.
Knee: Master knee point adjustment
Slope: Knee slope adjustment
Knee Sat: Knee saturation adjustment
M-VHS: Master V modulation shading adjustment
M Gamma: Master gamma adjustment
BlkGamma: Black gamma adjustment
Deail: Detail adjustment
SkinDtl: Skin detail adjustment
Ctrl: Selects the adjustment mode of the control knobs.
Rel: Relative mode
Abs: Absolute mode
Scal: Selects the adjustment range of the control knobs in Relative mode. The
adjustment range is set as a fraction of the entire variable range.
Selects the adjustment mode of the WHITE control knobs.
Rel: Relative mode, Abs: Absolute mode
Selects the adjustment range of the WHITE control knobs in Relative mode. The
adjustment range is set as a fraction of entire variable range.
Selects the function of the BLACK control knobs.
Black: Black balance adjustment
Flare: Flare balance adjustment
Selects the adjustment mode of the BLACK control knobs.
Rel: Relative mode, Abs: Absolute mode
Selects the adjustment range of the BLACK control knobs in Relative mode. The
adjustment range is set as a fraction of entire variable range.