Sony BVP-900 Series Product Information Manual page 106

10
Location and Function of Parts and Controls
(a) LOCK button
Press and illuminate the button to disable controls except those in
the iris/master black control block. Press the button again to enable
the controls.
(b) PARA (parallel mode) button
This button is illuminated when the Parallel mode is active, in which
simultaneous operation with another control panel is possible. When
this button is illuminated, all the buttons and controls on this panel
(except for the iris/master black control block) are active, even if the
PANEL ACTIVE button is not illuminated. If you press the button
when it is illuminated, the light goes out and the Parallel mode is
canceled.
(c) MASTER and SLAVE
When adjusting the white balance of multiple cameras in
Master/Slave mode, it is necessary to decide which is to be the
master camera and which are to be slave cameras. Press and
illuminate the MASTER button to specify the connected camera to be
the master. Press and illuminate the SLAVE button to specify the
connected camera to be a slave. The slave camera follows the master
camera settings. If you press a button when it is illuminated, the
illumination is turned off.
3) Power and output signal select block
a
CAM PW TEST1
(a) CAM PW (camera power) button
Press and illuminate this button to turn the power supply to the
camera ON. The button flashes until the camera is ready for
transmission.
When you press this button again, it starts flashing and the power
supply is turned off.
(b) Signal output select buttons
Press and illuminate one of these buttons to activate the camera test
signal generator and send the respective signals.
TEST: To send a sawtooth signal to test the video circuits.
BARS: To send a color bar signal.
Note The BARS button takes priority to the TEST button. If the BARS
button is illuminated, press the button to turn the illumination off before
pressing the TEST button.
4) AUTO SETUP block
a b
AUTO SETUP
SKIN DTL LEVEL START/
AUTO HUE BREAK
(a) Auto adjustment item select buttons
Press and illuminate these buttons to select the items to be
automatically adjusted.
SKIN DTL AUTO HUE: Skin tone detail automatic hue.
LEVEL: Gamma balance, knee point, master black level, etc.
(b) START/BREAK button
Press to start automatic adjustment of the selected items. The button
is illuminated during adjustment and the illumination is turned off
105
b
BARS
c d
WHITE BLACK
when the adjustments are complete. If you press the button while it
is illuminated, the automatic adjustment is canceled and the button
flashes. To stop it flashing, press the button again.
(c) WHITE (white balance) button
Press to automatically adjust the white balance. The button is
illuminated during adjustment and remains illuminated until the
adjustments are completed. If you press this button while it is
illuminated, or press the START/BREAK button, the automatic
adjustment is canceled and the button flashes. To stop it flashing,
press the button again.
(d) BLACK (black balance) button
Press to automatically adjust the black balance and black set. The
button is illuminated during adjustment and remains illuminated until
the adjustments are completed. If you press this button while it is
illuminated, or press the START/BREAK button, the automatic
adjustment is canceled and the button flashes. To stop it flashing,
press the button again.
Note If an error occurs during adjustment, the selected button flashes.
5) Camera/CCU function ON/OFF buttons
Various functions of the camera or the CCU-700A/700AP can be
turned on and off from this panel. The following switching functions
are assigned to seven of the buttons at the factory, while the extreme
right-hand button is reserved for future use. Press and illuminate
these buttons to turn on the respective functions. Press again so that
the button is not illuminated to turn off the function.
CHAR
ACTER
5600K AUTO SKIN DETAIL
KNEE DETAIL GATE
5600K: 5600K electronic color temperature conversion
function.
AUTO KNEE: Auto knee function. When this button is
illuminated, the knee point is automatically
adjusted according to the light content of the
picture.
SKIN DETAIL: Skin tone detail function.
DETAIL GATE: Skin tone detail gate function. When this
button is illuminated, the adjustment range of
the skin tone detail is displayed in white on the
monitor screen.
SATURATION: Saturation function.
BLACK GAMMA: Black gamma function.
CHARACTER: Self-diagnostic display function. When this
button is illuminated, the contents of the self-
diagnosis of the CCU-700A/700AP are displayed
on the monitor connected to the CHARACTER
OUTPUT connector or the CCU-700A/700AP.
The contents are also mixed with the video
signal to be output from the PIX1 OUTPUT
connector. Each time you press this button, the
status changes as follows.
OFF ON (page 1) ON (page 2)
The contents of the self-diagnosis may be displayed when required
even if this button is not illuminated.
SATURATION BLACK
GAMMA
... ON (page n)