Cisco TelePresence System C20 Administrator's Manual page 59

Cisco TelePresence System Quick Set C20 / C20 Plus and Profiles using C20
Contents Introduction
Video OSD InputMethod InputLanguage
The codec can be enabled for Cyrillic input characters in the menus on screen. NOTE: Requires
that xConfiguration Video OSD inputMethod Cyrillic is set to On.
Requires user role: ADMIN
Value space: <Latin/Cyrillic>
Latin: Latin characters can be entered when using the remote control (default).
Cyrillic: Cyrillic characters can be entered using the remote control. NOTE: Requires a Cisco
TelePresence Remote Control with Cyrillic fonts.
Example: Video OSD InputMethod InputLanguage: Latin
Video OSD InputMethod Cyrillic
Set the Cyrillic mode for the menu input language in the menus on screen.
Requires user role: ADMIN
Value space: <On/Off>
On: Cyrillic mode is available as a menu input language in the menus on screen. This will enable
the setting xConfiguration Video OSD InputMethod InputLanguage.
Off: Cyrillic mode is NOT available as a menu input language in the menus on screen.
Example: Video OSD InputMethod Cyrillic: Off
Video OSD LoginRequired
Determine if the system should require the user to login before accessing the On Screen Display
(OSD). If enabled, the user must enter his username and his PIN. After the user has logged in he
can only execute to the configurations changes and commands allowed by his Role.
Requires user role: ADMIN
Value space: <On/Off>
On: The user must log in to access the On Screen Display (OSD).
Off: No login to the OSD is required.
Example: Video OSD LoginRequired: Off
D14637.06 Profile C20 and Quick Set C20 Administrator Guide TC4.2, July 2011.
Copyright © 2010-2011 Cisco Systems, Inc. All rights reserved.
Web interface Advanced settings Advanced settings
Video AllowWebSnapshots
Set if the system shall be allowed to generate a web snapshot of the video input main source.
To generate and view the snapshot you must open a web browser, enter the IP address of the
codec, login to the Web interface, select Snapshot from the left menu, and press the button "Get
snapshot" .
NOTE: This is a local setting which is available only from the On Screen Display (OSD) and when
connected directly to the serial port (COM 1 port) on the codec.
Requires user role: ADMIN
Value space: <On/Off>
Example: Video AllowWebSnapshots: Off
Video Output HDMI [1..2] CEC Mode
The HDMI outputs support Consumer Electronics Control (CEC). When set to on (default is off),
and the monitor connected to the HDMI output is CEC compatible and CEC is configured, the
system will use CEC to set the monitor in standby when the system enters standby. Likewise the
system will wake up the monitor when the system wakes up from standby. Please note that the
different manufacturers uses different marketing names for CEC: Anynet+ (Samsung); Aquos Link
(Sharp); BRAVIA Sync (Sony); HDMI-CEC (Hitachi); Kuro Link (Pioneer); CE-Link and Regza Link
(Toshiba); RIHD (Onkyo); SimpLink (LG); HDAVI Control, EZ-Sync, VIERA Link (Panasonic); EasyLink
(Philips); and NetCommand for HDMI (Mitsubishi).
Requires user role: ADMIN
Value space: <On/Off>
Example: Video Output HDMI 1 CEC Mode: Off
Video Output HDMI [1..2] MonitorRole
The HDMI monitor role describes what video stream will be shown on the monitor connected to the
video output HDMI connector. Applicable only if the "Video > Monitors" configuration is set to dual.
Requires user role: ADMIN
Value space: <First/Second/PresentationOnly>
Example: Video Output HDMI 1 MonitorRole: First
59
Password protection
On: If set to on, a web snapshot can be generated and displayed on the web page under
"Snapshot" .
Off: The generation of web snapshots is not allowed.
On: Enable CEC control.
Off: Disable CEC control.
First: Show main video stream.
Second: Show presentation video stream if active, or other participants.
PresentationOnly: Show presentation video stream if active, and nothing else.
Administrator guide
Appendices Contact us
www.cisco.com