Cisco TelePresence System C20 Administrator's Manual page 58

Cisco TelePresence System Quick Set C20 / C20 Plus and Profiles using C20
Contents Introduction
Video MainVideoSource
Define which video input source shall be used as the main video source. The video input source is
configured with the "Video Input Source [1..2] Connector" setting.
Requires user role: USER
Value space: <1..2>
Range: Select the source to be used as the main video source.
Example: Video MainVideoSource: 1
Video Monitors
Set the monitor layout mode.
Requires user role: ADMIN
Value space: <Single/Dual/DualPresentationOnly>
Single: The same layout is shown on all monitors.
Dual: The layout is distributed on two monitors.
DualPresentationOnly: All participants in the call will be shown on the first monitor, while the
presentation (if any) will be shown on the second monitor.
Example: Video Monitors: Single
Video OSD Mode
The Video OSD (On Screen Display) Mode lets you define if information and icons should be
displayed on screen.
Requires user role: ADMIN
Value space: <On/Off/Disabled>
On: Display the on screen menus, icons and indicators.
Off: Hide the on screen menus, icons and indicators.
Disabled: When set to disabled, the C20 can use the additional resources usually used by
the GUI to do 1080p30 at the same time as sharing a presentation. The C20 must then be
controlled by a Cisco TelePresence Touch or and external control panel as the GUI will be
disabled.
Example: Video OSD Mode: On
Video OSD AutoSelectPresentationSource
Determine if the presentation source should be automatically selected.
Requires user role: ADMIN
Value space: <On/Off>
On: Enable automatic selection of the presentation source.
Off: Disable automatic selection of the presentation source.
Example: Video OSD AutoSelectPresentationSource: Off
D14637.06 Profile C20 and Quick Set C20 Administrator Guide TC4.2, July 2011.
Copyright © 2010-2011 Cisco Systems, Inc. All rights reserved.
Web interface Advanced settings Advanced settings
Video OSD TodaysBookings
This setting can be used to display the systems bookings for today on the main OSD menu. This
requires that the system is bookable by an external booking system, like Cisco TelePresence
Management Suite (TMS).
Requires user role: ADMIN
Value space: <On/Off>
Example: Video OSD TodaysBookings: Off
Video OSD MyContactsExpanded
Set how the local contacts will be displayed in the phone book dialog in the OSD (On Screen
Display).
Requires user role: ADMIN
Value space: <On/Off>
Example: Video OSD MyContactsExpanded: Off
Video OSD Output
The Video OSD (On Screen Display) Output lets you define which monitor should display the on
screen menus, information and icons. By default the OSD is sent to the monitor connected to the
Video OSD Output 1. If you cannot see the OSD on screen, then you must re-configure the OSD
Output. You can do this by entering a key sequence on the remote control, from the web interface,
or by a command line interface.
Using the remote control: Press the Disconnect key followed by: * # * # 0 x # (where x is output 1
to 2).
Using the web interface: Open a web browser and enter the IP address of the codec. Open the
Advanced Configuration menu and navigate to Video OSD Output and select the video output.
Using a command line interface: Open a command line interface and connect to the codec (if in
doubt of how to do this, see the API Guide for the codec). Enter the command: xConfiguration
Video OSD Output [1..2] (select the OSD Output)
Requires user role: ADMIN
Value space: <1..2>
Example: Video OSD Output: 1
58
Password protection
On: Displays information about this systems bookings on screen.
Off: Do not display todays bookings.
On: The local contacts in the phone book will be shown in the top level of the phonebook dialog.
Off: The local contacts will be placed in a separate folder called MyContacts in the phonebook
dialog.
Range: Select 1 for HDMI output, or select 2 for DVI-I output.
Administrator guide
Appendices Contact us
www.cisco.com