Advertisement
Quick Links
Cordless Jig Saw
Length
of stroke
MODEL 433ODWA
MODEL 4330DZ
INSTRUCTION MANUAL
I
weight
Net
Max. c u t t i n g capacities
Strokes
Overall
Wood
1
Mild steel
I
A l u m i n u m
per minute
length
SPECIFICATIONS
2 0 mm
1 3 5 m m
I
] ! $ $T
I
(,3/16,,1
I
2 , 8 0 0
I
2 8 0 m m
2'6
kg
2 6 m m
( 1 " )
I ( 5 - 5 / 1 6 " ]
( 1 1 " )
1
( 5 . 7 Ibs)
*
Manufacturer reserves the right to change specifications without notice.
*
Note: Specifications may differ from country to country.
WARNING: For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Advertisement
Related Manuals for Makita 4330DWA
Summary of Contents for Makita 4330DWA
- Page 1 Cordless Jig Saw MODEL 433ODWA MODEL 4330DZ INSTRUCTION MANUAL SPECIFICATIONS Max. c u t t i n g capacities Strokes Overall Length of stroke weight Wood Mild steel A l u m i n u m per minute length ] ! $ $T 2 6 m m 2 0 mm 1 3 5 m m...
- Page 2 GENERAL SAFETY RULES (For All Battery Operated Tools) WARNING! Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS Work Area Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.
- Page 3 Tool Use a n d Care Use clamps or other practical way t o secure and support the workpiece t o a stable platform. Holding the work by hand or against your body is unstable and may lead t o loss of control. Do not force tool.
- Page 4 Specific Safety Rules Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring. Contact with a "live" wire will also make exposed metal parts of the tool "live" and shock the operator. Be aware that this tool is always in an operating condition because does not have t o be plugged into an electrical outlet.
- Page 5 SYMBOLS The followings show the symbols used for tool ........volts ........minutes = ........direct current ........no load speed /min ........revolutions or reciprocation per minute...
- Page 6 IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER & BATTERY CARTRIDGE SAVE THESE INSTRUCTIONS This manual Length of Cord (Feet) 1 5 0 AWG Size of Cord Do not operate charger w i t h damaged cord or plug replace them im- mediately. I O .
- Page 7 ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (50OF) or ABOVE 4OoC (104OF). 2. Do not attempt t o use a step-up transformer, an engine generator or DC power receptacle.
- Page 8 Installing or removing the saw blade CAUTION: Always be sure that the tool is switched off and battery removed before installing or removing the blade. To install the blade, loosen the screw on the blade holder. Loosen Screw With the blade teeth facing forward, insert the blade into the blade holder as far as it will go.
- Page 9 Installing the universal shank jig saw blade CAUTION: Always be sure that the tool is switched off and battery removed before installing or removing the blade. If the universal blade clamp is used, you can use blades of other makes which have a universal shank like the one shown in the figure, with blade width of...
- Page 10 Switch action CAUTION: Before inserting the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released. Pulling the trigger hard when the lock off button is not pressed causes switch damage. To start the tool, simply push the lock off button then pull the trigger.
- Page 11 Bevel cutting CAUTIO N: Always remove the battery from the tool before making any adjustments With the base tilted, you can make bevel cuts at any angle between (left 0" 45" or right). Loosen the bolt on the bottom of the tool.
- Page 12 cutouts Cutouts can be made with either of two methods A or B. A) Boring a starting hole: For internal cut- outs without lead-in cut from an edge, pre-drill starting hole more than 12 mm (1 5/32”) in diameter. Insert the blade into this hole and hold the tool firmly against the workpiece to start your cut.
- Page 13 Metal cutting Always use suitable coolant (cutting oil) when cutting metal. Failure to do will cause significant blade wear. The underside of the workpiece can be greased instead using a coolant. Anti-splintering device To reduce the potential for workpiece sur- face splintering, the anti-splintering device can be used.
- Page 14 The vacuum head can Plastic cover be installed on either left or right side of Hook of vacuum head the base. Then connect a Makita vacuum cleaner to the vacuum head. Hose of vacuum head L - . -...
- Page 15 To maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. Recycling the Battery only way to dispose of a Makita battery is to recycle it.
- Page 16 ACCESSORIES CAUTION: tool These accessories or attachments are recommended for use with your Makita specified this manual. The use any other accessories or attachments might present risk injury t o persons. The accessories or attachments should be used only in the proper and intended manner.
- Page 17 Jia saw blade Application Blade Type Wood & olvwood Plastics Aluminum Mild Steel Feature thick thick Also ideal for cutting thick No. 51 11/16'' l/8"l 13/64" 1/4"l 13/64" 1B"I stainless steel. 60 mm thick thick For fast cutting. 15/32" 2-3/87 6 / 3 2 ' ' 2-3/8"1 mm thick...
- Page 18 Nov-19-'98 CORDLESS JIG SAW Model 43301) Note: The switch and other part configurations may differ from country to country.
- Page 19 MODEL 4330D N o r - 1 9 - ' 9 8 'i\M DESCRIPTION DESCRIPTION Switch Button Balance Plate Compression Spring 4 Housing Set (With Item 511 Balance Plate Tapping Screw 4x18 Flat Washer Tapping Screw 4 x 3 0 Flat Washer 6 Pan Head Screw M4x25 Pin 6...
- Page 20 ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, retum the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective workmanship or material, Makita...