Advertisement
Quick Links
Cordless Jig Saw
Length
of
stroke
2 6
mm
( 1
"1
MODEL 433ODWA
MODEL 4330D2
Strokes
Overall
N e t
Max. c u t t i n g capacities
Wood
M i l d steel
A l u m i n u m
per minute
length
w e i g h t
2 8 0 mm
2 . 6 k g
( 1
1")
(5.7 Ibs)
2,800
1 3 5 mm
1 0 mm
2 0 mm
( 5 - 5 1 1 6 " )
(318")
( 1
3 / 1 6 " )
INSTRUCTION MANUAL
SPEC I Fl CAT1 0 N
S
*
Manufacturer reserves the right to change specifications without notice.
Note: Specifications may differ from country to country.
WARNING: For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Advertisement
Related Manuals for Makita 433ODWA
Summary of Contents for Makita 433ODWA
- Page 1 M i l d steel A l u m i n u m per minute 1 0 mm 2 0 mm (318”) 3 / 1 6 “ ) MODEL 433ODWA MODEL 4330D2 Strokes Overall N e t length w e i g h t 2 8 0 mm 2 .
-
Page 2: General Safety Rules
GENERAL SAFETY RULES (For All Battery Operated Tools) WARNING! Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS Work Area Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. - Page 3 Tool Use and Care Use clamps or other practical way t o secure and support the workpiece t o a stable platform. Holding the work by hand or against your body is unstable and loss may lead t o of control. Do not force tool.
- Page 4 Specific Safety Rules Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring. Contact with a "live" wire will also make exposed metal parts of the tool "live" and shock the operator. 2.
- Page 5 The followings show the /min ... SYMBOLS symbols used for tool. volts minutes direct current no load speed revolutions reciprocation per minute...
- Page 6 IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER & BATTERY CARTRIDGE Length of Cord (Feet) AWG Size of Cord...
- Page 7 ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE Do not charge Battery Cartridge when temperature or ABOVE 4OoC (104OF). Do not attempt t o use a step-up transformer, an engine generator or DC power receptacle. Do not allow anything t o cover or clog the charger vents. 4.
- Page 8 Installing or removing the saw blade CAUTION: Always be sure that the tool is switched off and battery removed before installing or removing the blade. To install the blade, loosen the screw on the blade holder. With the blade teeth facing forward, insert the blade into the blade holder as far as it will go.
- Page 9 Installing the universal shank jig saw blade CAUTIO N : Always be sure that the tool is switched removing the blade. If the universal blade clamp is used, you can use blades of other makes which have a universal shank like the one shown in the figure, with a blade width of (1 /4"...
- Page 10 Switch action CAUTION: Before inserting the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released. Pulling the trigger hard when the lock off button is not pressed causes switch damage. To start the tool, simply push the lock off button then pull the trigger.
- Page 11 Bevel cutting CAUTION: Always remove the battery from the tool before making any adjustments With the base tilted, you can make bevel cuts at any angle between 0" and 45" (left or right). Loosen the bolt on the bottom of the tool.
- Page 12 cutouts Cutouts can be made with either of two methods A or A) Boring a starting hole: For internal cut- outs without lead-in cut from an edge, pre-drill a starting hole more than 12 mm (15/32") in diameter. Insert the blade into this hole and hold the tool firmly against the workpiece to start your cut.
- Page 13 Metal cutting Always use a suitable coolant (cutting oil) when cutting metal. Failure to do so will cause blade significant wear. coolant. Anti-splintering device To reduce the potential for workpiece sur- face splintering, the anti-splintering device can be used. Fit it into the base from below so that surrounds the sides Plastic base plate (optional accessory)
- Page 14 The vacuum head can be installed on either left or right side of the base. Then connect cleaner to the vacuum head. Makita vacuum into notches Base Plastic cover Hex wrench...
-
Page 15: Recycling The Battery
To maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. Recycling the Battery only way to dispose of a Makita battery is to recycle it. - Page 16 No. 8-25 50 mm (2") No. 8-26 50 mm (2") No. 8-27 No. BR-13 80 mm (3-1/8") No. 8-16L 70 mm (2-3/4") Makita with your tool specified in this risk injury to persons. of 1 1.25 m m (1E.2" 3/64") Part No.
- Page 17 & Wood plywood No 51 mm thick No' 58 l5/32"-2-3/8") 4 - 3 0 mm thick No, 59 15/32'' 1-1B"l NoB-10 3-60mmthick IlB" 2-3/8") thick (l/8" 1-1/8") 60 mm thick f13/64" 2-3/8"1 60 mm thick 15/32'' 2-3/8") thick 15/64'' 1-1/8") 30 mm thick N ' .
- Page 18 CORDLESS JIG SAW Model 43300 Note: The switch and other part configurations may differ from country to country. Nov.-19-'98...
- Page 19 MODEL 4 3 3 0 0 DESCRIPTIDN MACHINE Switch Button i i b compress,on S p m g 4 ; I ; Housing Set i W l h Item 511 Tapping Screw 4x18 Tapping Screw 4x30 Pan Head Screw M4x25 Switch Switch Lever Battery Holder...
-
Page 20: Warranty Policy
Should any trouble develop during this one-year period return the COMPLETE tool, freight prepaid, t o one of Makita’s Factory or Authorized Service Ceders. If inspection shows the trouble is caused by defective workmanship or material, Makita will repair (or at our option, replace) without charge.