Usingthe Wall-Mounteddoor Control - Craftsman 139.53918D Owner's Manual

Usingthe Wall-MountedDoor Control
THE SMART CONTROLPANEL ®
Press the push button
to open or close the
door. Press again to
reverse the door during
the closing cycle or to
stop the door while it's
opening.
This door control
contains a motion
detector that will
automatically turn on
the light when it detects
Motion Detecting
Light On/Off
Prog <Learn>
Hour
Minute --
Language _i
Degrees (F/C) J
_._z L Push Bar
_ LightButton
\ Lock Button
a person entering the garage. This feature can be easily turned off
for extended work light use.
HT Light Feature
Press the Light button to turn the opener light on or off. It will not
control the opener lights when the door is in motion. If you turn it
on and then activate the opener, the light will remain on for 4-1/2
minutes. Press again to turn it off sooner. The 4-1/2 minute
interval can be changed to 1-1/2, 2-1/2, or 3-1/2 minutes as
follows: Press and hold the Lock button until the light blinks
(about 10 seconds). A single blink indicates that the timer is reset
to 1-1/2 minutes. Repeatthe procedure and the light will blink
twice, resetting the timer to 2-1/2 minutes. Repeat again for a
3-1/2 minute interval, etc., up to a maximum of four blinks and
4-1/2 minutes. When using the opener lights as working lights, we
recommend that you first disable the motion sensor.
f'h
LOC [_]K LockFeature
Designed to prevent operation of the door from
hand-held remote controls. However, the door will open and close
from the door control, the outdoor key switch and the keyless
Entry accessories.
To activate, press and hold the Lock button for 2 seconds.
To turn off, press and hold the Lock button again for 2 seconds.
The Lock feature will also turn off whenever the "learn" button on
the motor unit panel is activated.
Motion Detecting Light Feature:The opener light will turn on
automatically when a person walks in front of the wall-mounted
door control. This feature works by detecting motion and body
heat and may not work in temperatures around 100°F(37.7° C).
The opener light will come on for 5 minutes, then shut off
automatically if no additional motion or heat differential is
calculated.
_To disable this the Automatic On/
feature, press
Light
Off button on the left side of the door control.
We recommend that you disable the motion sensor
when using the opener lights as working lights. Otherwise, they
will turn off automatically if you are working beyond the sensor's
range.
PROG<Learn> Feature
The door control is equipped with a PROG<LEARN>button to
assist in learning remote controls to the unit. Press the PROG
<LEARN>button once to initiate LEARN mode and the display will
show 'Learn Remote Control - Press Learn Button Again to
Confirm.' Press the PROG<LEARN>button a second time and
the display will show 'Learn Mode - Press Remote Control Button
to Learn Remote.' Press the button of the remote control to be
learned and the worklight will blink to confirm the remote control
has been learned.
H--_--M Hour and Minute Feature
v
Press or hold either of these side buttons to
increment the hour or minute displayed on the LCD display.
<LANG>LanguageFeature
Press this side button to toggle between the three languages -
English, Spanish, and French.
Degrees F/C Feature
Press th s s de button to toggle the temperature units
between Fahrenheitand Celsius.
Additional feature when used with the 3-Button
hand-held remote
To control the opener lights:
1. With the door closed, press and hold a small remote button
that you want to control the light.
2. Press and hold the Light button on the door
control.
3. While holding the Light button, press and
hold the Lock button on the door control.
4. After the opener lights flash, releaseall buttons.
31