Makita GA7082 Instruction Manual
Hide thumbs
Also See for GA7082:
- Instruction manual (148 pages) ,
- Instruction manual (120 pages) ,
- Instruction manual (108 pages)
Related Manuals for Makita GA7082
Summary of Contents for Makita GA7082
- Page 1 INSTRUCTION MANUAL Angle Grinder GA7080 GA7081 GA7082 GA9080 GA9081 GA9082 DOUBLE INSULATION Read before use.
-
Page 2: Specifications
220 V and 250 V The followings show the symbols which may be used for the equipment. Be sure that you understand their Only for model GA7082 / GA9082 meaning before use. Switching operations of electric apparatus cause volt- age fluctuations. - Page 3 Electrical safety Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away Power tool plugs must match the outlet. Never from moving parts. Loose clothes, jewellery or modify the plug in any way. Do not use any long hair can be caught in moving parts.
-
Page 4: Grinder Safety Warnings
Keep cutting tools sharp and clean. Properly Do not use a damaged accessory. Before each maintained cutting tools with sharp cutting edges use inspect the accessory such as abrasive wheels for chips and cracks, backing pad for are less likely to bind and are easier to control. cracks, tear or excess wear, wire brush for Use the power tool, accessories and tool bits loose or cracked wires. - Page 5 Kickback and Related Warnings Do not use worn down wheels from larger Kickback is a sudden reaction to a pinched or snagged power tools. Wheel intended for larger power tool rotating wheel, backing pad, brush or any other acces- is not suitable for the higher speed of a smaller sory.
-
Page 6: Functional Description
NEVER USE Stone Cup type wheels with this FUNCTIONAL grinder. This grinder is not designed for these types of wheels and the use of such a product DESCRIPTION may result in serious personal injury. Be careful not to damage the spindle, the flange (especially the installing surface) or the CAUTION: Always be sure that the tool is... -
Page 7: Indication Lamp
For tool with the lock-on and lock-off Switch action switch CAUTION: Before plugging in the tool, always Country specific check to see that the switch trigger actuates properly and returns to the "OFF" position when CAUTION: Switch can be locked in "ON" posi- released. -
Page 8: Soft Start Feature
Unintentional restart proof Installing or removing loop handle Only for model GA7080 / GA7081 / GA9080 / GA9081 Optional accessory The tool does not start with the switch being lock-on CAUTION: Always be sure the bolts on the even when the tool is plugged. loop handle is securely tightened before use. - Page 9 For tool with locking screw type Mount the wheel guard with the protrusions on the wheel guard band aligned with the notches on the bear- wheel guard ing box. Then rotate the wheel guard to such an angle that it can protect the operator according to work. Mount the wheel guard with the protrusions on the wheel guard band aligned with the notches on the bear- ing box.
- Page 10 Flange. Those flanges are so thick that the entire thread cannot be retained by the spindle. Mount inner flange, abrasive wheel and Ezynut onto the spindle so that Makita Logo on Ezynut faces outside. Fig.13 ► 1. Lock nut wrench 2. Shaft lock To remove the wheel, follow the installation procedure in reverse.
- Page 11 Press shaft lock firmly and tighten Ezynut by turning the Installing or removing abrasive disc abrasive wheel clockwise as far as it turns. Optional accessory Fig.16 ► 1. Shaft lock Fig.19 ► 1. Sanding lock nut 2. Abrasive disc 3. Rubber pad To loosen the Ezynut, turn the outside ring of Ezynut counterclockwise.
- Page 12 For Australia and New Zealand Installing wire wheel brush ø45 Optional accessory CAUTION: Do not use wire wheel brush that ø78 is damaged, or which is out of balance. Use of damaged wire wheel brush could increase potential for injury from contact with broken wires. CAUTION: ALWAYS use guard with wire wheel brushes, assuring diameter of wheel fits...
-
Page 13: Operation
Dust collecting wheel guard for cut-off (for model OPERATION GA9080 / GA9081 / GA9082) WARNING: It should never be necessary to force the tool. The weight of the tool applies ade- quate pressure. Forcing and excessive pressure could cause dangerous wheel breakage. WARNING: ALWAYS replace wheel if tool is dropped while grinding. - Page 14 It may lead to premature Fig.28 breakage. Usage example: operation with abrasive cut-off Usage example: operation with wire cup brush wheel with GA7081 / GA7082 / GA9081 / GA9082 Fig.32 Fig.29 14 ENGLISH...
-
Page 15: Maintenance
To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. NOTE: Do not loosen the screw on the cover. Otherwise the cover may be opened accidentally. -
Page 16: Optional Accessories
The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center. Fig.36... - Page 17 180 mm 230 mm Lock nut wrench Dust cover attachment NOTE: *1 Only for tools with M14 spindle thread. NOTE: *2 Do not use Super flange and Ezynut together. NOTE: *3 In some European countries, when using a diamond wheel, the ordinary guard can be used instead of the special guard covering the both side of the wheel.
- Page 20 Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan 885884-904 www.makita.com 20221206...