G1014Z Stand; G1014Z Labels & Cosmetics - Grizzly G1014Z Owner's Manual

113
12
13
111
58
41
G1014Z Labels & Cosmetics
130
REF PART # DESCRIPTION
104V2 P1014Z104V2 MACHINE ID LABEL V2.08.22
121 P1014Z121 ENTANGLEMENT LABEL
128 P1014Z128 MODEL NUMBER LABEL
129V2 P1014Z129V2 COMBO WARNING LABEL V2.08.22
BUY PARTS ONLINE AT GRIZZLY.COM!
-56-
Scan QR code to visit our Parts Store.

G1014Z Stand

109A
32
13
12
13
112
109
12
13
110
136
131
Motor: 3/4 HP, 110V/220V, 1-Phase, 60 Hz
Prewired Voltage: 110V
Full Load Amps: 12A (110V); 6A (220V)
Belt Arm Tilt: 0–90°
Sanding Belt Size: 6" x 48"
Sanding Belt Speed: 1900 FPM
Table Tilt: 0–45°
Sanding Disc Diameter: 9"
Sanding Disc Speed: 2420 RPM
Weight: 117 lbs.
Mfd. for Grizzly in Taiwan
G1014Z
REF PART #
12 P1014Z012
13 P1014Z013
32 P1014Z032
41 P1014Z041
58 P1014Z058
65 P1014Z065
65
109 P1014Z109
109A P1014Z109A STAND ASSEMBLY
110 P1014Z110
111 P1014Z111
112 P1014Z112
113 P1014Z113
65
121
WARNING!
ENTANGLEMENT
HAZARD!
Tie back long hair, roll up
long sleeves, and remove
loose clothing, jewelry, or
gloves to prevent getting
caught in moving parts.
129V2
WARNING!
WARNING!
To reduce risk of death EYE/LUNG INJURY
or serious injury, read
HAZARD!
manual BEFORE using
Always wear safety
machine.
glasses and a
To get a new manual, call
respirator when
(800) 523-4777 or go to
using this machine.
www.grizzly.com.
WARNING!
ABRASION
INJURY HAZARD!
DO NOT touch moving
sanding belt or disc,
or personal injury may
occur!
104V2
MODEL G1014Z
6" X 48" BELT/9" DISC COMBO SANDER
Specifications
WARNING!
To reduce risk of serious personal injury when using this machine:
1. Read and understand owner's manual before operating.
2. Always wear approved eye protection and respirator.
3. Only plug power cord into a grounded outlet.
4. Support workpiece with miter gauge, backstop, or worktable.
5. Maintain 1/16" maximum clearance between table and sandpaper.
6. Never touch moving sandpaper.
7. Always sand in accordance with directional arrows on machine.
8. Make sure sander is properly assembled, adjusted, and stable before operating. Only operate with all guards in place.
9. Never sand pointed stock with point facing into sanding rotation, and never force workpiece into sanding surface.
10. Only remove jammed pieces when sandpaper is stopped.
11. Turn motor OFF and disconnect power before changing sandpaper, making adjustments, or servicing.
Date 12. Do not wear loose clothing, gloves, jewelry, or other articles that can get entangled. Tie back long hair and roll up sleeves.
13. Never reach over moving sanding disc or belt.
14. Do not expose to rain or use in damp locations.
S/N
15. Do not operate under influence of drugs or alcohol, or when tired.
16. Prevent unauthorized use by children or untrained users; restrict access or disable machine when unattended.
128
REF PART #
130 P1014Z130
131 P1014Z131
136 P1014Z136
Model G1014Z/G1014ZX (Mfd. Since 08/22)
DESCRIPTION
HEX NUT 5/16-18
FLAT WASHER 5/16
HEX BOLT 5/16-18 X 1/2
HEX BOLT 5/16-18 X 1
RUBBER FOOT
CARRIAGE BOLT 5/16-18 X 5/8
LEG
LOWER BRACE (LONG)
LOWER BRACE (SHORT)
UPPER BRACE (LONG)
UPPER BRACE (SHORT)
136
DESCRIPTION
TOUCH-UP PAINT, GRIZZLY GREEN
TOUCH-UP PAINT, GRIZZLY BLACK
ELECTRICITY LABEL