G1014Z Inventory - Grizzly G1014Z Owner's Manual

G1014Z Inventory

The following is a list of items shipped with your
machine. Before beginning setup, lay these items
out and inventory them.
If any non-proprietary parts are missing (e.g. a
nut or a washer), we will gladly replace them; or
for the sake of expediency, replacements can be
obtained at your local hardware store.
Box 1 (Figures 9–11)
A. Sander Unit ................................................. 1
B. Stand Legs .................................................. 4
C. Long Lower Braces ..................................... 2
D. Long Upper Braces ..................................... 2
E. Short Lower Braces ..................................... 2
F.
Short Upper Braces ..................................... 2
G. Sanding Belt 6" x 48" .................................. 1
H. Dust Port 2
⁄ " (Black) .................................. 1
1
2
I. Work Table .................................................. 1
J.
Miter Gauge ................................................. 1
K. Back Stop .................................................... 1
L. Rubber Feet ................................................ 4
M. Table Support Rod ...................................... 1
N. Quick Release Lever Stud 6" ...................... 1
O. Short Lever Arm .......................................... 1
P. Quick Release Lever Handle ...................... 1
Q. Idler Roller ................................................... 1
R. Idler Roller Guard ........................................ 1
S. Dust Port 2" (Green) .................................... 1
T.
Cast Iron Plate ............................................. 1
U. Sanding Disc 9" ........................................... 1
Hardware & Tools (not shown)
• Hex Wrench 4mm ........................................ 1
• Hex Bolts ⁄ "-18 x 1" (Feet) ........................ 4
5
16
• Hex Nuts ⁄ "-18 (Feet, Stand) .................. 36
5
16
• Flat Washers ⁄ " (Feet, Stand) ................. 40
5
16
• Hex Bolts ⁄ "-18 x
5
16
• Carriage Bolts ⁄ "-18 x
5
16
• Phillip Head Screws 10-24 x
(2 ⁄ " Dust Port) ............................................ 4
1
2
• Hex Nuts 10-24 (2
1
• Flat Washers #10 (2
• Hex Nuts ⁄ "-16 (Quick Release Lever) ...... 2
3
8
• Thumb Knobs ⁄ "-20 x
1
4
• Flat Washers ⁄ " (Sander Unit) .................... 2
1
4
• Thumb Knobs M5-.8 x 10 (Roller Guard) .... 2
• Flat Washers #10 (Roller Guard) ................. 2
• Lock Washers #10 (Roller Guard) ............... 2
Model G1014Z/G1014ZX (Mfd. Since 08/22)
Qty
Qty
⁄ " (Stand & Sander) .... 4
1
2
⁄ " (Stand) ........... 32
1
2
⁄ "
3
8
⁄ " Dust Port) .................. 4
2
1 ⁄ " Dust Port) ............... 4
2
⁄ " (Sander Unit) ..... 2
1
2
A
Figure 9. G1014Z sander unit.
B
Figure 10. G1014Z stand components.
G
U
T
Q
V
S
R
Figure 11. Loose inventory items.
NOTICE
If you cannot find an item on this list, care-
fully check around/inside the machine and
packaging materials. Often, these items get
lost in packaging materials while unpack-
ing or they are pre-installed at the factory.
C E
D
F
H
I
J
K
M
L
N
O
P
-17-