Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Makita DDF083Z
Summary of Contents for Makita DDF083Z
- Page 1 INSTRUCTION MANUAL Cordless Driver Drill DDF483 DDF083 Read before use.
-
Page 2: Specifications
SPECIFICATIONS Model: DDF483 DDF083 Drilling capacities Steel 13 mm Wood 36 mm Fastening Wood screw 6 mm x 75 mm capacities Machine screw No load speed High (2) 0 - 1,700 min Low (1) 0 - 500 min Overall length 162 mm 124 mm Rated voltage... -
Page 3: General Power Tool Safety Warnings
Prevent unintentional starting. Ensure the SAFETY WARNINGS switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with General power tool safety warnings your finger on the switch or energising power tools that have the switch on invites accidents. WARNING: Remove any adjusting key or wrench before Read all safety warnings and... -
Page 4: Cordless Driver Drill Safety Warnings
Use of non-genuine Makita batteries, or batteries that SAVE THESE INSTRUCTIONS. have been altered, may result in the battery bursting causing fires, personal injury and damage. It will also void the Makita warranty for the Makita tool and WARNING: DO NOT let comfort or familiarity charger. with product (gained from repeated use) replace... -
Page 5: Functional Description
Never recharge a fully charged battery car- Indicating the remaining battery tridge. Overcharging shortens the battery capacity service life. Charge the battery cartridge with room tem- Only for battery cartridges with "B" at the end of the perature at 10 °C - 40 °C (50 °F - 104 °F). Let model number a hot battery cartridge cool down before charging it. -
Page 6: Overdischarge Protection
Overdischarge protection Lighting up the front lamp When the battery capacity is not enough, the tool stops automatically. In this case, remove the battery from the tool and charge the battery. NOTE: Overheat protection (for battery) will work only with batteries with star marking. ► 1 . -
Page 7: Speed Change
This tool has a reversing switch to change the direction CAUTION: Always set the speed change lever of rotation. Depress the reversing switch lever from the fully to the correct position. If you operate the A side for clockwise rotation or from the B side for coun- tool with the speed change lever positioned halfway terclockwise rotation. between the "1" side and "2" side, the tool may be When the reversing switch lever is in the neutral posi- damaged. - Page 8 For tool with deep driver bit hole ASSEMBLY A=17mm To install these types of driver B=14mm bits, follow the procedure 1. CAUTION: Always be sure that the tool is A=12mm To install these types of driver switched off and the battery cartridge is removed B=9mm bits, follow the procedure 2. before carrying out any work on the tool.
-
Page 9: Screwdriving Operation
Hold the tool firmly with one hand on the grip and the Installing hook other hand on the bottom of the battery cartridge to control the twisting action. ► 1 . Groove 2. Hook 3. Screw Screwdriving operation The hook is convenient for temporarily hanging the tool. This can be installed on either side of the tool. To install the hook, insert it into a groove in the tool housing on CAUTION: Adjust the adjusting ring to the either side and then secure it with a screw. To remove,... -
Page 10: Optional Accessories
CAUTION: These accessories or attachments CAUTION: Hold the tool firmly and exert care are recommended for use with your Makita tool when the drill bit begins to break through the specified in this manual. The use of any other workpiece. There is a tremendous force exerted on accessories or attachments might present a risk of the tool/drill bit at the time of hole break through. - Page 12 Makita Europe N.V. Jan-Baptist Vinkstraat 2, 3070 Kortenberg, Belgium Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan 885507-221 www.makita.com 20160317...