Page 1
Instruction Manual Original Instruction Manual EA3200S EA3201S EA3202S EA3203S Important: Read this instruction manual carefully before putting the chain saw into operation and strictly observe the safety regulations! Keep this instruction manual!
Table of contents Page Delivery inventory .............. 3 Congratulations on choosing a MAKITA chain saw! We are confi‑ dent that you will be satisfied with this modern piece of equipment. Symbols ................3 The EA3200S, EA3201S, EA3202S, EA3203S are very handy SAFETY PRECAUTIONS and robust chain saws with a new Design.
Delivery inventory 1. Chain saw 2. Guide bar 3. Saw chain 4. Chain protection cover 5. Universal wrench In case one of the parts listed should not be included in the 6. Screwdriver for carburetor adjustment delivery inventory, please consult your sales agent. 7.
SAFETY PRECAUTIONS Intended use Power chain saws ‑ Protective gloves (6) made of thick leather are part of the prescribed equipment and must always be worn during op‑ This power chain saw may be used only for sawing wood out eration of the chain saw.
Fuels / Refuelling ‑ Stop the engine before refuelling the chain saw. ‑ Do not smoke or work near open fires (5). ‑ Let the engine cool down before refuelling. ‑ Fuels can contain substances similar to solvents. Eyes and skin should not come in contact with mineral oil products.
Kickback ‑ When working with the chain saw dangerous kickbacks may occur. ‑ Kickback occurs when the upper part of the end of the guide bar inadvertently touches wood or other hard objects (10). ‑ This causes the saw to be thrown back toward the user with great force and out of control.
Page 7
‑ Be careful when cutting splintery wood. Cut pieces of wood may be pulled along (risk of injuries). ‑ When cutting with the upper edge of the guide bar, the chain saw may be pushed in the direction of the user if the chain gets clamped.
All other work must be carried out by MAKITA Service. Use only original MAKITA spare parts and accessories. Using spare parts other than original MAKITA parts or ac‑ cesories and guide bar/chain combinations or lengths which are not approved bring a high risk of accidents. We cannot...
Figures derived in equal part from full‑load and racing speed. Uncertainty (K=). Packing Your MAKITA chain saw comes delivered in a protective cardboard box to protect against shipping damage. Cardboard is a basic raw material and is consequently reuseable or suitable for recycling (waste paper recycling).
PUTTING INTO OPERATION Only for models with fastening nuts on the sprocket guard CAUTION: Before doing any work on the guide bar or chain, al- ways switch off the engine and pull the plug cap off the spark plug (see “Replacing the spark plug”). Always wear protective gloves! CAUTION: Start the chain saw only after having assembled it...
Lift the chain (9) over the sprocket (8). CAUTION: Do not insert the chain between the chain sprocket and the disc. Guide the chain from above about halfway into the groove (10) on the guide bar. CAUTION: Note that the cutting edges along the top of the chain must point in the direction of the arrow! Pull the chain (9) around the sprocket nose (11) of the guide bar in the direction of the arrow.
Checking the chain tension The tension of the chain is correct if the chain rests against the bottom side of the guide bar and can still be easily turned by hand. While doing so the chain brake must be released. Check the chain tension frequently ‑...
Only for the QuickSet guide bar CAUTION: Before doing any work on the guide bar or chain, al- ways switch off the engine and pull the plug cap off the spark plug (see “Replacing the spark plug”). Always wear protective gloves! CAUTION: Start the chain saw only after having assembled it com- pletely and inspected.
Pull the chain (6) around the sprocket nose (8) of the guide bar in the direction of the arrow. Replace the sprocket guard (3). IMPORTANT: Lift the saw chain over the chain catcher (9). Tighten the nuts (2) only hand‑tight to begin with. Tensioning the saw chain Turn the QuickSet chain tensioner (10) to the right (clockwise) using the combination tool, until the saw chain guide elements...
Only for models with quick ten- sioner on sprocket guard (TLC) CAUTION: Before doing any work on the guide bar or chain, al- ways switch off the engine and pull the plug cap off the spark plug (see “Replacing the spark plug”). Always wear protective gloves! CAUTION: Start the chain saw only after having assembled it com-...
Pull the chain (8) around the sprocket nose (10) of the guide bar in the direction of the arrow. Align hole on sprocket guard (4) with the pin (11). Turn the chain tensioner (3, see “Tightening the saw chain”) to bring the chain tensioner pin (12) into alignment with the hole in the guide bar.
Tension the chain as already described. For all models Chain brake The EA3200S, EA3201S, EA3202S, EA3203S comes with an inertia chain brake as standard equipment. If kickback occurs due to contact of the guide‑bar tip with wood (see SAFETY PRECAUTIONS, page 6), the chain brake will stop the chain through inertia if the kickback is sufficiently strong.
980 008 611 oil may even be required by local regulations. The chain oil BIOTOP sold by MAKITA is made of special Bio‑degradable oil is stable only for a limited period of time. It vegetable oils and is 100% bio‑degradable. BIOTOP has should be used within 2 years from the date of manufacture been granted the “blue angel”...
Important note on bio-degradable chain oils The next time you use the saw, fill the tank with BIOTOP If you are not planning to use the saw again for an extended period of time, empty the oil tank and put in a small amount of chain oil again.
Checking the chain lubrication Never work with the chain saw without sufficient chain lubri ‑ ca tion. Otherwise the service life of the chain and guide bar will be reduced. Before starting work check the oil level in the tank and the oil feed. Check the oil feed rate as described below: Start the chain saw (see “Starting the engine”).
Starting the engine Do not start the chain saw until after it is completely assembled and checked! Move at least 3 meters / 10 feet away from the place where the chain saw was fuelled. Make sure you have a secure footing, and place the saw on the ground in such a way that the guide bar and chain are not near anything.
Bring the engine back to idle and release the chain brake. Caution: If the chain does not stop immediately in this test, turn off the engine immediately. Do NOT use the chain saw in this condition! Contact a MAKITA autho- rized service center.
Idle speed decreases. Turn adjusting screw (S) clockwise (screw in): Idle speed increases. Important: If the saw chain still moves during idle even after you have adjusted the idle speed, do NOT use the saw. Take it to a MAKITA service center!
MAINTENANCE Sharpening the saw chain CAUTION: Before doing any work on the guide bar or chain, always switch off the engine and pull the plug cap off the spark plug (see “Replacing the spark plug”). Always wear protective gloves! The chain needs sharpening when: The sawdust produced when sawing damp wood looks like wood flour.
Page 26
Files and how to work with them Use a special saw chain round file for sharpening. Standard round files are unsuitable. See “Extract from the spare parts list”. Type 092 (91VG), 492 (91PX): Saw chain round file, dia. 4.0 mm. Type 290 (90SG): Saw chain round file, dia.
The chain brake is a very important safety device and like any other component subject to normal wear and tear. Regular inspection and maintenance are important for your own safety and must be done by a MAKITA service center. SERVICE Cleaning the guide bar CAUTION: Protective gloves must be worn.
Replacing the saw chain CAUTION: Use only chains and guide bars designed for this saw (see the Extract from the spare‑parts list)! Check the sprocket before mounting a new chain. Worn out sprockets (8) may damage the new chain and must therefore be replaced.
Cleaning the air filter CAUTION: To prevent eye injury, always wear eye protec- tion when cleaning the filter with compressed air! Do not use fuel to clean the air filter. Pull out the hood cap (1). Loosen the scew (2) counter‑clockwise and remove the hood (3).
Replacing the spark plug CAUTION: 0.6 mm Do not touch the spark plug or plug cap if the engine is running (high voltage). Switch off the engine before starting any maintenance work. A hot engine can cause burns. Wear protective gloves! The spark plug must be replaced in case of damage to the insulator, electrode erosion (burn) or if the electrodes are...
Replacing the starter cable/ Replacing the return spring pack/Replacing the starter spring Unscrew three screws (1). Remove fan housing (2). Remove the air guide (3) from the fan housing. CAREFUL! Injury hazard! Do not unscrew screw (7) if the return spring is under tension. If the starter cable is to be replaced although it is not broken, it will be necessary to first de‑tension the cable drum return spring (13).
Cleaning the air filter compartment / fan com- partment Remove cover. Remove the fan housing. CAUTION: To prevent eye injury, always wear eye protec- tion when cleaning the filter with compressed air! The entire area (15) can now be brushed clean or cleaned with compressed air.
Guarantee claims can be recognized only if this work is performed regularly and properly. Failure to perform the prescribed maintenance work can lead to accidents! The user of the chain saw must not perform maintenance work which is not described in the instruction manual. All such work must be carried out by a MAKITA service center. Page General Chain saw Clean exterior, check for damage.
Trouble shooting Malfunction System Observation Cause Chain does not run Chain brake Engine runs Chain brake actuated. Engine does not Ignition system Ignition spark Malfunction in fuel supply system, compression start or only with system, mechanical malfunction. difficulty No ignition spark STOP switch in position, fault or short‑circuit in the wiring, Spark plug cap or spark plug...
Extract from the spare parts list EA3200S, EA3201S Use only original MAKITA parts. For repairs and EA3202S, EA3203S replacement of other parts, see your MAKITA service center. 30/31...
Page 37
Extract from the spare parts list EA3200S, EA3201S Use only original MAKITA parts. For repairs and EA3202S, EA3203S replacement of other parts, see your MAKITA service center. Spare parts Accessories (not delivered with the chain saw) Pos. Qty. Denomination Chain gauge, type 092 (91VG), 492 (91PX) Sprocket nose bar 3/8”, 30 cm, 1.3 mm (12”)
For European countries only 12. EC Declaration of Conformity We Makita Corporation as the responsible manufacturer declare that the following Makita machine(s): Designation of Machine: Petrol Chain Saw Model No./ Type: EA3200S, EA3201S Specifications: see “TECHNICAL DATA” table. are of series production and...
Page 40
Makita Corporation Anjo, Aichi, Japan www.makita.com 884987D228...