Specifications; Ec Declaration Of Conformity - Makita DCO140 Instruction Manual

ENGLISH (Original instructions)

SPECIFICATIONS

Collet chuck capacity
Rated speed (n)/ No load speed (n
Overall length
Rated voltage
• Due to our continuing program of research and development, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi-
est combination, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
Battery cartridge
Charger
• Some of the battery cartridges and chargers listed above may not be available depending on your region of
residence.
WARNING:
Only use the battery cartridges and chargers listed above. Use of any other battery cartridges
and chargers may cause injury and/or fire.
Intended use
The tool is intended for cutting gypsum, wood, plastic
and soft wall tiles.
Noise
The typical A-weighted noise level determined accord-
ing to EN62841-2-17:
Sound pressure level (L
Uncertainty (K) : 3 dB (A)
The noise level under working may exceed 80 dB (A).
NOTE: The declared noise emission value(s) has
been measured in accordance with a standard test
method and may be used for comparing one tool with
another.
NOTE: The declared noise emission value(s)
may also be used in a preliminary assessment of
exposure.
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the power tool can differ from the declared
value(s) depending on the ways in which the
tool is used especially what kind of workpiece is
processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
Model
)
0
Net weight
D.C.14.4 V Model
D.C.18 V Model
) : 77 dB (A)
pA
DCO140
3 mm, 6 mm or 1/8", 1/4"
1.6 kg
D.C. 14.4 V
BL1415N / BL1430B / BL1440 / BL1460B
BL1815N / BL1820B / BL1830B / BL1840B / BL1850B / BL1860B
DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF /
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN62841-2-17:
Work mode : rotation without load
Vibration emission (a
Uncertainty (K) : 1.5 m/s
NOTE: The declared vibration total value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE: The declared vibration total value(s) may also
be used in a preliminary assessment of exposure.
WARNING:
The vibration emission during
actual use of the power tool can differ from the
declared value(s) depending on the ways in which
the tool is used especially what kind of workpiece
is processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).

EC Declaration of Conformity

For European countries only
The EC declaration of conformity is included as Annex A
to this instruction manual.
5 ENGLISH
DCO180
-1
30,000 min
313 mm
1.5 - 1.8 kg
D.C. 18 V
DC18SH
2
) : 2.5 m/s or less
h
2