Installing The Water Filter - Makita DVC152L Instruction Manual

ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
CAUTION:
Always wear dust mask during
assembly or maintenance.
Installing the powder filter (HEPA)
and prefilter (for dry dust)
Optional accessory for cloth filter model
CAUTION:
Never pick up water or other liq-
uids or wet dusts when using the powder filter.
Picking up such things may cause the powder filter
breakage.
To use powder filter:
1.
Remove the float cage and float by removing the
bolts.
► Fig.11: 1. Float 2. Float cage
2. Place the prefilter in the tank with aligning the
mounting position markings.
3. Mount the damper on the powder filter and then
place them in the prefilter with aligning the mounting
position markings.
4.
Finally, mount the tank cover and lock it.
► Fig.12: 1. Tank cover 2. Powder filter (HEPA)
3. Damper 4. Prefilter 5. Tank 6. Mounting
position marking
NOTICE:
Before using the powder filter, make
sure that prefilter and damper are always used
together. It is not allowed to install powder filter
solely.

Installing the water filter

Optional accessory for cloth filter model
CAUTION:
Never pick up water or wet dust
without the float and the cloth filter or the water
filter.
CAUTION:
For picking up wet dust, make
sure that the float cage and the float are installed
on the cleaner.
CAUTION:
When installing the water filter on
the tank, set it tight at the opening of the tank so
that the hook of the water filter engages the tank
opening firmly and there is no space between the
water filter and the tank.
To pick up water or wet dust only, the water filter is more
suitable than the cloth filter.
When installing the water filter, align its mounting posi-
tion mark with the one on the tank.
► Fig.13: 1. Water filter 2. Tank 3. Mounting position
marking
NOTE: It is recommended using water filter when
picking up large amount of water repeatedly.
Otherwise vacuum ability may be reduced in case of
cloth filter.
Installing the paper pack
Optional accessory
WARNING:
use the cloth filter or prefilter together that is
preinstalled on the cleaner. Failure to use the cloth
filter / prefilter together may cause unusual noise and
heat, resulting in a fire.
CAUTION:
(For the cloth filter model)
• Never pick up water or other liquids or wet
dusts when using the paper pack. Picking
up such things may cause the paper pack
breakage.
• Before using the paper pack, make sure that
powder filter (optional accessory), damper
(optional accessory) and prefilter are always
used together.
CAUTION:
(For the powder filter model)
• Before using the paper pack, make sure
that powder filter, damper and prefilter are
always used together.
1. Remove the rubber holder.
► Fig.14: 1. Rubber holder
2. Extend the paper pack.
3.
Align the paper pack opening with the dust suction
opening of the cleaner.
4. Insert the cardboard of the paper pack onto the
holder so that it is positioned at the end beyond the
detent protrusion.
► Fig.15: 1. Paper pack 2. Holder
Installing the polyethylene bag
Cleaner can also be used without polyethylene bag.
However, using polyethylene bag is easier to empty the
tank without letting your hands dirty.
Spread the polyethylene bag in the tank. Insert it
between the holder plate and the tank, and pull it to the
hose inlet.
► Fig.16: 1. Holder plate 2. Polyethylene bag
Spread the bag around the top of the tank so that the
cloth filter / prefilter edge can catch and hold the bag
securely.
► Fig.17: 1. Cloth filter / prefilter
NOTE: A polyethylene bag available on the
market can be used. 0.04 mm or thicker one is
recommended.
NOTE: Too much dust will tear the bag easily, so
do not collect the dust more than the half of the bag
capacity.
14 ENGLISH
When using the paper pack, also