Makita DVC152L Instruction Manual page 16

NOTE: T h e w ireless a c ti v ation lamp on t h e tool w ill stop
blinking in blue w h en t h ere is no operation f or 2 h ours. I n
t h is c ase, set t h e stan d -b y s w it c h on t h e c leaner to " A U T O "
an d press t h e w ireless a c ti v ation button on t h e tool again.
NOTE: T h e c leaner starts / stops w it h a d ela y . T h ere is a time
lag w h en t h e c leaner d ete c ts a s w it c h operation o f t h e tool.
NOTE: T h e transmission d istan c e o f t h e w ireless unit ma y
v ar y d epen d ing on t h e lo c ation an d surroun d ing c ir c umstan c es.
NOTE: W h en tw o or more tools are registered to one c leaner,
th e c leaner may start running ev en if y ou d on' t pull th e sw itc h trig-
ger bec ause oth er user is using th e w ireless ac tiv ation f unc tion.
Cancelling tool registration for the cleaner
P er f orm t h e f ollo w ing pro c e d ure w h en c an c elling t h e
tool registration f or t h e c leaner.
1. I nstall t h e batteries to t h e c leaner an d t h e tool.
2. S et t h e stan d -b y s w it c h on t h e c leaner to " A U T O " .
Fig.28: 1. S tan d -b y s w it c h
3. P ress t h e w ireless a c ti v ation button on t h e c leaner
f or 6 se c on d s. T h e w ireless a c ti v ation lamp blinks in
green an d t h en be c ome re d . A f ter t h at, press t h e w ire-
less a c ti v ation button on t h e tool in t h e same w a y .
Fig.29: 1. W ireless a c ti v ation button 2. W ireless
a c ti v ation lamp
I f t h e c an c ellation is per f orme d su c c ess f ull y , t h e w ire-
less a c ti v ation lamps w ill lig h t up in re d f or 2 se c on d s
an d start blinking in blue.
Description of the wireless activation lamp status
Fig.31: 1. W ireless a c ti v ation button 2. W ireless
a c ti v ation lamp
T h e w ireless a c ti v ation lamp s h o w s t h e status o f t h e w ireless a c ti v ation f un c tion. R e f er to t h e belo w table f or t h e
meaning o f t h e lamp status.
Status
Color
S tand by Blue
T ool G reen
registration
C anc elling/ R ed
erasing
( slow : 2 times/ sec .)
tool
registration
( f ast: 5 times/ sec .)
O th ers R ed
O f f
W ireless activation lamp
Duration
On Blinking
C leaner: c on-
tinuing
T ool: 2 h ours
W h en th e tool is
running.
20 sec ond s
2 sec ond s
20 sec ond s
W h en th e
w ireless ac ti-
v ation button is
pressed d ow n.
2 sec ond s
3 sec ond s
-
NOTE: The wireless activation lamps finish blinking in
re d a f ter 20 se c on d s elapse d . P ress t h e w ireless a c ti-
v ation button on t h e tool w h ile t h e w ireless a c ti v ation
lamp on t h e c leaner is blinking. I f t h e w ireless a c ti-
v ation lamp d oes not blink in re d , pus h t h e w ireless
activation button briefly and hold it down again.
Erasing all tool registrations
Y ou c an erase all tool registrations f rom t h e c leaner as f ollo w s.
Fig.30: 1. S tan d -b y s w it c h 2. W ireless a c ti v ation
button 3. W ireless a c ti v ation lamp
1. I nstall t h e batteries to t h e c leaner.
2. S et t h e stan d -b y s w it c h to " A U T O " .
3. H ol d d o w n t h e w ireless a c ti v ation button f or about
6 se c on d s until t h e w ireless a c ti v ation lamp blinks in re d
( about t w i c e per one se c on d ) .
4. W h en t h e w ireless a c ti v ation lamp starts blinking
in red, release your finger from the wireless activation
button. T h erea f ter, h ol d d o w n t h e w ireless a c ti v ation
button again f or about 6 se c on d s.
5. W h en t h e w ireless a c ti v ation lamp starts blinking
f ast ( about 5 times per one se c on d ) in re d , release y our
finger from the wireless activation button. When the
w ireless a c ti v ation lamp lig h ts up in re d an d later lig h ts
o f f , all tool registrations are erase d .
NOTE: I f t h e w ireless a c ti v ation lamp d oes not blink in re d ,
press the wireless activation button briefly and try again.
W aiting f or th e tool registration or th e w ireless ac tiv ation f unc tion
is av ailable.
T h e lamp on th e c leaner blinks w h en th e stand -by sw itc h is set in
A U T O . T h e lamp on th e tool blinks w h en th e w ireless ac tiv ation
button is push ed . T h e lamp on th e tool w ill automatic ally turn of f
w h en no operation is perf ormed f or 2 h ours.
T h e w ireless ac tiv ation of th e c leaner is av ailable and th e tool is
running.
R ead y f or th e tool registration. S earc h ing th e tool to be registered .
The tool registration has been finished. The wireless activation
lamp w ill start blinking in blue.
R ead y f or th e c anc ellation of th e tool registration. S earc h ing th e
tool to be c anc elled .
R ead y to erase all tool registrations.
T h e tool registration h as been c anc elled / erased . T h e w ireless
ac tiv ation lamp w ill start blinking in blue.
T h e pow er is supplied to th e w ireless unit and th e w ireless ac tiv a-
tion f unc tion is starting up.
- T h e stand -by sw itc h is not set to " A U T O " .
16 ENGLISH
Description