Honeywell Notifier LCD2-80 Instruction Manual page 3

Installation Precautions
Adherence to the following will aid in problem-free installation with
long-term reliability:
WARNING - Several different sources of power can
be connected to the fire alarm control panel. Dis-
connect all sources of power before servicing. Control
unit and associated equipment may be damaged by
removing and/or inserting cards, modules, or intercon-
necting cables while the unit is energized. Do not
attempt to install, service, or operate this unit until man-
uals are read and understood.
CAUTION - System Re-acceptance Test after Soft-
ware Changes: To ensure proper system operation,
this product must be tested in accordance with NFPA
72 after any programming operation or change in site-
specific software. Re-acceptance testing is required
after any change, addition or deletion of system com-
ponents, or after any modification, repair or adjustment
to system hardware or wiring. All components, circuits,
system operations, or software functions known to be
affected by a change must be 100% tested. In addi-
tion, to ensure that other operations are not inadvert-
ently affected, at least 10% of initiating devices that are
not directly affected by the change, up to a maximum of
50 devices, must also be tested and proper system
operation verified.
This system meets NFPA requirements for operation
at 0-49º C/32-120º F and at a relative humidity 93% ±
2% RH (noncondensing) at 32°C ± 2°C (90°F ± 3°F).
However, the useful life of the system's standby batter-
ies and the electronic components may be adversely
affected by extreme temperature ranges and humidity.
Therefore, it is recommended that this system and its
peripherals be installed in an environment with a nor-
mal room temperature of 15-27º C/60-80º F.
Verify that wire sizes are adequate for all initiating
and indicating device loops. Most devices cannot tol-
erate more than a 10% I.R. drop from the specified
device voltage.
FCC Warning
WARNING:
This equipment generates, uses,
and can radiate radio frequency energy and if not
installed and used in accordance with the instruction
manual may cause interference to radio communica-
tions. It has been tested and found to comply with the
limits for class A computing devices pursuant to Sub-
part B of Part 15 of FCC Rules, which is designed to
provide reasonable protection against such interfer-
ence when devices are operated in a commercial
environment. Operation of this equipment in a resi-
dential area is likely to cause interference, in which
case the user will be required to correct the interfer-
ence at his or her own expense.
HARSH™ NIS™ Notifier Integrated Systems™
, ,
Acclimate® Plus
,
VeriFire® VIEW®
, and
Notifier Integrated Systems™
FlashScan® NION®
,
all registered trademarks of Honeywell International Inc.
Systems™ NOTI•FIRE•NET™
, and
NOTIFIER® ONYX®
,
Honeywell International Inc. Acclimate® Plus, SpectrAlert® and System Sensor® are all registered trademarks of
Honeywell International Inc. Silent Knight® is a registered trademark of Honeywell International Inc.
is a registered trademark and
trademark of Datapoint Corporation.
LCD2-80 Instruction Manual — P/N 53242:A 08/18/2009
FlashScan® NION®
,
are all registered trademarks of Honeywell International Inc.
NOTI•FIRE•NET™
, and
NOTIFIER® ONYX®
, ,
are all trademarks; and
ONYXWorks®, UniNet®
,
LonWorks™
is a trademark of Echelon Corporation.
Microsoft®
Like all solid state electronic devices, this system
may operate erratically or can be damaged when sub-
jected to lightning induced transients. Although no sys-
tem is completely immune from lightning transients and
interference, proper grounding will reduce susceptibil-
ity. Overhead or outside aerial wiring is not recom-
mended, due to an increased susceptibility to nearby
lightning strikes. Consult with the Technical Services
Department if any problems are anticipated or encoun-
tered.
Disconnect AC power and batteries prior to remov-
ing or inserting circuit boards. Failure to do so can
damage circuits.
Remove all electronic assemblies prior to any drill-
ing, filing, reaming, or punching of the enclosure. When
possible, make all cable entries from the sides or rear.
Before making modifications, verify that they will not
interfere with battery, transformer, or printed circuit
board location.
Do not tighten screw terminals more than 9 in-lbs.
Over-tightening may damage threads, resulting in
reduced terminal contact pressure and difficulty with
screw terminal removal.
This system contains static-sensitive compo-
nents. Always ground yourself with a proper wrist
strap before handling any circuits so that static charges
are removed from the body. Use static suppressive
packaging to protect electronic assemblies removed
from the unit.
Follow the instructions in the installation, operating,
and programming manuals. These instructions must be
followed to avoid damage to the control panel and
associated equipment. FACP operation and reliability
depend upon proper installation.
Canadian Requirements
This digital apparatus does not exceed the Class A
limits for radiation noise emissions from digital appa-
ratus set out in the Radio Interference Regulations of
the Canadian Department of Communications.
Le present appareil numerique n'emet pas de bruits
radioelectriques depassant les limites applicables
aux appareils numeriques de la classe A prescrites
dans le Reglement sur le brouillage radioelectrique
edicte par le ministere des Communications du Can-
ada.
NOTI•FIRE•NET™
, and
NOTIFIER® ONYX®
, ,
are all trademarks; and
ONYXWorks®, UniNet®
,
HARSH™
Acclimate® Plus
VeriFire® VIEW®
, , and
Windows®
and are registered trademarks of the Microsoft
Precau-D1-9-2005
are all trademarks; and
ONYXWorks®, UniNet®
,
HARSH™
Acclimate® Plus
VeriFire® VIEW®
, , and
NIS™ Notifier Integrated
, ,
FlashScan®
,
are all registered trademarks of
ARCNET®
is a registered
,
NIS™
, ,
,
are
NION®
, ,
Echelon®
3