Removing The Blower Module - Cisco 6400 Maintaining

Hide thumbs Also See for 6400:
Table of Contents

Advertisement

Replacing the Blower Module

Removing the Blower Module

To remove the blower module from the Cisco 6400 chassis:
If you are using AC PEMs, remove the AC power cords from the clips on the blower module.
Step 1
Step 2
Detach the cable management brackets
Figure 5-39 Detaching a Cable Management Bracket
Fold the loaded brackets to either side of the Cisco 6400 chassis, leaving the cables attached. The
Step 3
20-inch service loop will allow you to pull the cables out of the way of the blower
Figure 5-40 Folding Cables and Brackets away from the Blower
Remove the two screws on the front of the blower module
Step 4
Carefully slide the blower out of the chassis.
Step 5
Place the blower module on a flat work surface.
Step 6
Cisco 6400 Hardware Installation and Maintenance Guide
5-48
(Figure
5-39).
FANS
FAN
MULTI-
OK
FAILUR E
FAN
CAUTIO N: WHEN HOT
FAILUR E
SWAPP ING THIS
FAN TRAY, REMOV AL AND
REPLAC ING
MUST BE DONE IN UNDER
THREE
MINUTE S OR OVER HEATIN
G MAY
OCCUR .
1
2
3
4
0A
PRO CES SOR ONL Y 0B
NRP
NRP
OC-3
OC-3
STM-1
NSP
STM-1
NSP
FAIL
FAIL
PORT 0
PORT 0
CON
TX
CON
RX
TX
RX
STATUS
STATUS
AUX
PORT 1
PORT 1
AUX
TX
RX
TX
RX
STATUS
STATUS
ACT
ACT
ETH
ETH
LNK
LNK
PCMC IA
PCMC IA
FANS
FAN
MULTI-
OK
FAILUR E
FAN
CAUTIO N: WHEN HOT
FAILUR E
SWAPP ING THIS
FAN TRAY, REMOV AL AND
REPLAC ING
MUST BE DONE IN UNDER
THREE
MINUTE S OR OVER HEATIN
G MAY
OCCUR .
1
2
3
4
0A
PRO CES SOR ONL Y 0B
NRP
NRP
OC-3
OC-3
STM-1
NSP
STM-1
NSP
FAIL
FAIL
PORT 0
PORT 0
CON
TX
RX
CON
TX
RX
STATUS
STATUS
AUX
PORT 1
PORT 1
AUX
TX
RX
TX
RX
STATUS
STATUS
ACT
ACT
ETH
ETH
LNK
LNK
PCMC IA
PCMC IA
Chapter 5
5
6
7
8
OC-3
OC-3
OC-3
STM-1
STM-1
NRP
STM-1
FAIL
FAIL
FAIL
PORT 0
PORT 0
PORT 0
TX
RX
TX
RX
TX
RX
STATUS
STATUS
STATUS
PORT 1
PORT 1
PORT 1
TX
RX
TX
RX
TX
STATUS
RX
STATUS
STATUS
SUB
SLOT
0
5
6
7
8
OC-3
OC-3
OC-3
STM-1
STM-1
NRP
STM-1
FAIL
FAIL
FAIL
PORT 0
PORT 0
PORT 0
TX
RX
TX
RX
STATUS
TX
RX
STATUS
STATUS
PORT 1
PORT 1
PORT 1
TX
RX
TX
RX
TX
STATUS
RX
STATUS
STATUS
SUB
SLOT
0
(Figure
5-41).
Maintaining the Cisco 6400
(Figure
5-40).
OL-2133-02

Advertisement

Table of Contents
loading

Table of Contents