Cisco UCS C22 Installation And Service Manual
  1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Server
  5. UCS C22
  6. Installation and service manual

Cisco UCS C22 Installation And Service Manual

Hide thumbs Also See for UCS C22:
Table of Contents

Advertisement

Quick Links

Download this manual
Enlarged version
Cisco UCS C22 Server
Installation and Service Guide
Covers Server Generation M3
November 16, 2012
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
OL-26646-01
Text Part Number:

Advertisement

Table of Contents
loading

Related Manuals for Cisco UCS C22

Summary of Contents for Cisco UCS C22

  • Page 1 Cisco UCS C22 Server Installation and Service Guide Covers Server Generation M3 November 16, 2012 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883 OL-26646-01 Text Part Number:...
  • Page 2 Cisco and/or its affiliates in the United States and certain other countries. Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/trademarks.

  • Page 3: Table Of Contents

    Procedure 1: Reboot With recovery.cap File 2-15 Procedure 2: Use Recovery Jumper and recovery.cap File 2-16 Maintaining the Server C H A P T E R Server Monitoring and Management Tools Cisco Integrated Management Interface (CIMC) Cisco UCS C22 Server Installation and Service Guide OL-26646-01...
  • Page 4 RAID Controller Card Cable Routing 3-32 Replacing a Cisco USB Flash Drive 3-33 Overview of the Pre-Loaded 16-GB Cisco USB Flash Drive 3-33 Enabling a Pre-Loaded Cisco USB Flash Drive Virtual Drive 3-33 Booting a Pre-Loaded Cisco USB Flash Drive Virtual Drive...
  • Page 5 LSI MegaRAID Card Beep Codes C-19 Restoring RAID Configuration After Replacing a RAID Controller C-20 For More Information C-20 Installation for Cisco UCS Integration A P P E N D I X Cisco UCS C22 Server Installation and Service Guide OL-26646-01...
  • Page 6 Contents Cisco UCS C22 Server Installation and Service Guide OL-26646-01...

  • Page 7: Related Documentation

    Preface This preface describes the audience, organization, and conventions of the Cisco UCS C22 Server Installation and Service Guide. It also provides information about how to obtain related documentation Related Documentation The documentation set for the Cisco Unified Computing System (UCS) C-Series rack-mount servers is...

  • Page 8: Documentation Feedback

    Preface Audience This guide is for experienced network administrators who configure and maintain Cisco servers. Documentation Feedback To provide technical feedback on this document, or to report an error or omission, please send your comments to ucs-docfeedback@external.cisco.com. We appreciate your feedback.
  • Page 9 å forhindre ulykker. Bruk nummeret i slutten av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne enheten. TA VARE PÅ DISSE INSTRUKSJONENE Cisco UCS C22 Server Installation and Service Guide OL-26646-01...
  • Page 10 Använd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning. SPARA DESSA ANVISNINGAR Cisco UCS C22 Server Installation and Service Guide OL-26646-01...
  • Page 11 Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de oversatte advarsler, der fulgte med denne enhed. GEM DISSE ANVISNINGER Cisco UCS C22 Server Installation and Service Guide OL-26646-01...
  • Page 12 Preface Cisco UCS C22 Server Installation and Service Guide OL-26646-01...

  • Page 13: Obtaining Documentation And Submitting A Service Request

    Obtaining Documentation and Submitting a Service Request For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at: http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html...
  • Page 14 Preface Cisco UCS C22 Server Installation and Service Guide OL-26646-01...
  • Page 15 This chapter provides an overview of the Cisco UCS C22 server features. This server is a part of the Cisco UCS C-Series rack-mount server family. It is a high-performance, 1RU (rack-unit) server. It is designed to operate in both standalone environments and as part of the Cisco Unified Computing System (UCS).
  • Page 16 Note In a single-CPU configuration, only 6 DIMM slots are active. Baseboard Pilot III BMC, running Cisco Integrated Management Controller (CIMC) firmware. management Depending on your CIMC settings, the CIMC can be accessed through the  1-Gb Ethernet dedicated management port, the dual 1-Gb Ethernet LOM ports, or a Cisco P81E virtual interface card.

  • Page 17: Chapter 1 Overview

    The server can be ordered with an optional blank 8-GB Cisco USB Flash Drive pre-installed in the internal USB port. Cisco USB Flash The server can be ordered with one pre-loaded 16-GB Cisco USB flash drive in the Drive  accessory kit.
  • Page 18 Chapter 1 Overview Cisco UCS C22 Server Installation and Service Guide OL-26646-01...

  • Page 19: Installing The Server

    Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device.  Statement 1071 SAVE THESE INSTRUCTIONS Cisco UCS C22 Server Installation and Service Guide OL-26646-01...

  • Page 20: Chapter 2 Installing The Server

    Description of damage • Effect of damage on the installation Figure 2-1 Shipping Box Contents HDD01 HDD02 HDD03 HDD04 HDD04 HDD04 HDD05 HDD05 HDD05 HDD06 HDD07 HDD08 Server Documentation Power cord – Cisco UCS C22 Server Installation and Service Guide OL-26646-01...

  • Page 21: Preparing For Server Installation

    Avoid UPS types that use ferroresonant technology. These UPS types can become unstable with systems Caution such as the Cisco UCS, which can have substantial current draw fluctuations from fluctuating data traffic patterns. Cisco UCS C22 Server Installation and Service Guide...

  • Page 22: Rack Requirements

    The minimum vertical rack space per server must be one RU, equal to 1.75 in. (44.45 mm). Equipment Requirements The slide rails supplied by Cisco Systems for this server do not require tools for installation. The inner rails (mounting brackets) are pre-attached to the sides of the server.

  • Page 23: Installing The Server In A Rack

    Release the clip marked “PULL” to lock the securing latch in the open position. Figure 2-2 Front Securing Latch Clip marked “PULL” on rear of assembly Spring-loaded securing latch on front of assembly Front mounting pegs Cisco UCS C22 Server Installation and Service Guide OL-26646-01...
  • Page 24 The inner rails are pre-attached to the sides of the server at the factory. You can order replacement inner rails if these are damaged or lost (Cisco PID UCSC-RAIL1-I). Align the inner rails that are pre-attached to the server sides with the front ends of the empty slide rails.
  • Page 25 Flange on rear of right mounting bracket Outer CMA arm attachment clip Flange on rear of outer right slide rail Continue with the “Initial Server Setup” section on page 2-8. Step 5 Cisco UCS C22 Server Installation and Service Guide OL-26646-01...

  • Page 26: Initial Server Setup

    DHCP is enabled. Shared LOM EXT mode enables the 1-Gb Ethernet ports and the ports on any installed Cisco virtual interface card (VIC) to access the Cisco Integrated Management Interface (CIMC). If you want to use the dedicated management ports to access the CIMC, you can...
  • Page 27 Cisco card connection is not getting its IP address from a Cisco UCS Manager system because the server is in standalone mode, further DHCP requests from the Cisco card are disabled. Use the Cisco Card NIC mode if you want to connect to the CIMC through a Cisco card in standalone mode.
  • Page 28 The default user name for the server is admin. The default password is password. Note To manage the server, see the Cisco UCS C-Series Rack-Mount Server Configuration Guide or the Cisco UCS C-Series Rack-Mount Server CLI Configuration Guide for instructions on using those interfaces.

  • Page 29: Nic Modes And Nic Redundancy Settings

    LOM and Cisco Card interfaces are both enabled. In this mode, DHCP replies are returned to both the shared LOM ports and the Cisco card ports. If the system determines that the Cisco card connection is not getting its IP address from a Cisco UCS Manager system because the server is in standalone mode, further DHCP requests from the Cisco card are disabled.

  • Page 30: System Bios And Cimc Firmware

    Note Your system firmware must be at minimum level 1.2 to use the Cisco Host Upgrade Utility. If your firmware is prior to level 1.2, you must use the methods below to update the BIOS and CIMC firmware individually.

  • Page 31: Accessing The System Bios

    Step 6 Follow the instructions on the Exit menu screen to save your changes and exit the setup utility (or Press F10). You can exit without saving changes by pressing Esc. Cisco UCS C22 Server Installation and Service Guide 2-13 OL-26646-01...

  • Page 32: Service Headers And Jumpers

    SYS FAN4 SYS FAN4 SYS FAN3 SYS FAN5 SYS FAN5 SYS FAN4 CPU 2 SYS FAN6 SYS FAN6 SYS FAN5 3 2 1 3 2 1 – CN34 BIOS Recovery Cisco UCS C22 Server Installation and Service Guide 2-14 OL-26646-01...

  • Page 33: Using The Bios Recovery Header Cn34

    During the BIOS update, the CIMC will shut down the server and the screen will be blank for about 10 minutes. Do not unplug the power cords during this update. The CIMC will power on the server after the update is complete. Cisco UCS C22 Server Installation and Service Guide 2-15 OL-26646-01...

  • Page 34: Procedure 2: Use Recovery Jumper And Recovery.cap File

    Replace the top cover, replace the server in the rack, replace power cords and any other cables, then Step 14 power on the server by pressing the Power button. Cisco UCS C22 Server Installation and Service Guide 2-16 OL-26646-01...

  • Page 35: Server Monitoring And Management Tools

    Server Monitoring and Management Tools Cisco Integrated Management Interface (CIMC) You can monitor the server inventory, health, and system event logs by using the built-in Cisco Integrated Management Controller (CIMC) GUI or CLI interfaces. See the user documentation for your firmware release at the following URL: http://www.cisco.com/en/US/products/ps10739/products_installation_and_configuration_guides_list.html...

  • Page 36: Chapter 3 Maintaining The Server

    Green—The server is in main power mode. Power is supplied to all server • components. Identification Off—The Identification LED is not in use. • Blue—The Identification LED is activated. • Cisco UCS C22 Server Installation and Service Guide OL-26646-01...
  • Page 37 • Off—There is no hard drive in the hard drive sled (no access, no fault). Green—The hard drive is ready. • Green, blinking—The hard drive is reading or writing data. • Cisco UCS C22 Server Installation and Service Guide OL-26646-01...

  • Page 38: Rear Panel Leds And Buttons

    Green, blinking—Traffic is present on the active link. 10/100/1000 Ethernet dedicated • Off—link speed is 10 Mbps. management link speed Amber—link speed is 100 Mbps. • Green—link speed is 1 Gbps. • Cisco UCS C22 Server Installation and Service Guide OL-26646-01...
  • Page 39 Green—Link is active. • Green, blinking—Traffic is present on the active link. • Identification Off—The Identification LED is not in use. • Blue—The Identification LED is activated. • Cisco UCS C22 Server Installation and Service Guide OL-26646-01...

  • Page 40: Preparing For Server Component Installation

    Emergency shutdown—Press and hold the Power button for 4 seconds to force the main power off • and immediately enter standby mode. Disconnect the power cords from the power supplies in your server to completely power off the server. Step 3 Cisco UCS C22 Server Installation and Service Guide OL-26646-01...

  • Page 41: Removing And Replacing The Server Top Cover

    Removing the Top Cover or Front Chassis Panel Front panel lip Top cover Front chassis panel Top cover thumbscrew Front chassis panel securing screws (two, one on each side of the panel) Cisco UCS C22 Server Installation and Service Guide OL-26646-01...

  • Page 42: Removing And Replacing The Front Chassis Panel

    Replace the two screws that secure the panel to the chassis (see Figure 3-3). Replace the top cover to the server as described in Removing and Replacing the Server Top Cover, page 3-7. Cisco UCS C22 Server Installation and Service Guide OL-26646-01...

  • Page 43: Replaceable Component Locations

    (on motherboard under PCIe riser 1) (RAID backup unit) Serial Number Location The serial number for the server is printed on a label on the top of the server, near the front. Cisco UCS C22 Server Installation and Service Guide OL-26646-01...

  • Page 44: Installing Or Replacing Server Components

    Replacing a Cisco USB Flash Drive, page 3-33 • Replacing the SuperCap Power Module (RAID Backup Unit), page 3-37 • Installing a Trusted Platform Module, page 3-39 • Replacing Power Supplies, page 3-42 Cisco UCS C22 Server Installation and Service Guide 3-10 OL-26646-01...

  • Page 45: Replacing Hard Drives Or Solid State Drives

    With the ejector lever on the drive tray open, insert the drive tray into the empty drive bay. Push the tray into the slot until it touches the backplane, then close the ejector lever to lock the drive in place. Cisco UCS C22 Server Installation and Service Guide 3-11 OL-26646-01...

  • Page 46: Replacing A Front Operations Panel Board

    Disconnect the two ribbon cables from the front operations panel board. To disconnect the ribbon cables, open their hinged connectors. Use a #2 Phillips-head screwdriver to remove the two screws that secure the board to the chassis. Cisco UCS C22 Server Installation and Service Guide 3-12 OL-26646-01...
  • Page 47 Replacing the Front Operations Panel Board SYS FAN1 CPU 1 PCIe 1 SYS FAN2 SYS FAN3 SYS FAN4 PCIe 2 CPU 2 SYS FAN5 PSU 1 1 Hinged ribbon-cable connectors (two) 2 Securing screws (two) Cisco UCS C22 Server Installation and Service Guide 3-13 OL-26646-01...

  • Page 48: Replacing A Drive Backplane

    Reconnect the two ribbon cables to the front operations panel board. Open a hinged ribbon-cable connector and insert the end of a ribbon cable squarely into the connector until it stops, and then close the hinged connector. Cisco UCS C22 Server Installation and Service Guide 3-14 OL-26646-01...
  • Page 49 1 Front panel control board cable connectors 3 Location of opening in backplane assembly for front operations panel ribbon cables 2 Backplane securing screw locations (two on – backplane assembly and two on exterior sides) Cisco UCS C22 Server Installation and Service Guide 3-15 OL-26646-01...

  • Page 50: Replacing Fan Modules

    SYS_FAN4 SYS_FAN5 SYS_FAN6 To replace or install a fan module, follow these steps: Caution The fans in the Cisco UCS C22 server are not hot-swappable. Step 1 Remove a fan module that you are replacing (see Figure 3-10): Power off the server as described in the “Shutting Down and Powering Off the Server”...

  • Page 51: Replacing Dimms

    DIMMs and their sockets are fragile and must be handled with care to avoid damage during installation. Caution Caution Cisco does not support 3rd-party DIMMs. Using non-Cisco DIMMs in the server might result in system problems or damage to the motherboard. Note To ensure the best server performance, it is important that you are familiar with memory performance guidelines and population rules before you install or replace memory.

  • Page 52: Memory Performance Guidelines And Population Rules

    DIMM Population Rules, page 3-19 • Memory Mirroring, page 3-20 • DIMM Slot Numbering Figure 3-11 shows the numbering of the DIMM slots. Figure 3-11 DIMM Slots and CPUs CPU1 CPU2 Cisco UCS C22 Server Installation and Service Guide 3-18 OL-26646-01...
  • Page 53 Memory mirroring reduces the amount of memory available by 50% because only one of the two populated channels provides data. When memory mirroring is enabled, DIMMs must be installed in sets of 2 or 4, as described in Memory Mirroring, page 3-20. Cisco UCS C22 Server Installation and Service Guide 3-19 OL-26646-01...
  • Page 54 Table 3-5 Memory Mirroring DIMM Population, Two CPUs Number of DIMMs  per CPU CPU 1 Population CPU2 Population A0; B0 D0; E0 A0, B0; A1, B1 D0, E0; D1, E1 Cisco UCS C22 Server Installation and Service Guide 3-20 OL-26646-01...

  • Page 55: Dimm Replacement Procedure

    Replace the air baffle and the top cover. Replace the server in the rack, replace cables, and then power on the server by pressing the Power button. Cisco UCS C22 Server Installation and Service Guide 3-21 OL-26646-01...

  • Page 56: Replacing Cpus And Heatsinks

    The Pick-and-Place tools used in this procedure are required to prevent damage to the contact pins between the motherboard and the CPU. Do not attempt this procedure without the required tools, which are included with each CPU option kit. If you do not have the tool, you can order a spare (Cisco PID UCS-CPU-EN-PNP).
  • Page 57 Use the tool as shown in Figure 3-13 to grasp the protective cap and then pivot to remove the cap. Figure 3-13 Protective Cap Removal Tool Cisco UCS C22 Server Installation and Service Guide 3-23 OL-26646-01...
  • Page 58 Make sure that the tabs on the tool are fully seated in the slots on the pedestal. Press the top button on the tool to grasp and lock in the CPU. Lift the tool and CPU straight up off the pedestal. Cisco UCS C22 Server Installation and Service Guide 3-24 OL-26646-01...
  • Page 59 Apply an alcohol-based cleaning solution to the old thermal pad and let it soak for a least 15 seconds. Wipe all of the old thermal pad off the old heatsink using a soft cloth that will not scratch the heatsink surface. Cisco UCS C22 Server Installation and Service Guide 3-25 OL-26646-01...
  • Page 60 Alternate tightening each screw evenly to avoid damaging the heatsink or CPU. Replace the top cover. Replace the server in the rack, replace cables, and then power on the server by pressing the Power button. Cisco UCS C22 Server Installation and Service Guide 3-26 OL-26646-01...

  • Page 61: Replacing The Motherboard Rtc Battery

    Push the battery into the socket until it is fully seated. Replace the top cover. Replace the server in the rack, replace cables, and power on the server by pressing the Power button. Cisco UCS C22 Server Installation and Service Guide 3-27 OL-26646-01...

  • Page 62: Replacing A Pcie Riser

    “Removing and Replacing the Server Top Cover” section on page 3-7. Lift straight up on both ends of the PCIe riser to disengage its circuit board from the socket on the motherboard. Cisco UCS C22 Server Installation and Service Guide 3-28 OL-26646-01...
  • Page 63 PCIe 1 SYS FAN2 SYS FAN3 SYS FAN4 PCIe 2 CPU 2 SYS FAN5 PSU 1 Chassis alignment points for PCIe riser 1 Chassis alignment points for PCIe riser 2 Cisco UCS C22 Server Installation and Service Guide 3-29 OL-26646-01...

  • Page 64: Replacing A Pcie Card

    Replacing a PCIe Card Caution Cisco supports all PCIe cards qualified and sold by Cisco. PCIe cards not qualified or sold by Cisco are the responsibility of the customer. Although Cisco will always stand behind and support the C-Series rack-mount servers, customers using standard, off-the-shelf, third-party cards must go to the third-party card vendor for support if any issue with that particular third-party card occurs.

  • Page 65: Replacing A Pcie Card

    Chapter 3 Maintaining the Server Installing or Replacing Server Components Replacing a PCIe Card If you are installing a Cisco UCS Virtual Interface Card, there are prerequisite considerations. See Note Special Considerations for Cisco UCS Virtual Interface Cards, page 3-32.

  • Page 66: Special Considerations For Cisco Ucs Virtual Interface Cards

    After Replacing a RAID Controller, page C-20. Special Considerations for Cisco UCS Virtual Interface Cards Table 3-7 describes the requirements for the supported Cisco UCS virtual interface cards (VICs). Table 3-7 Cisco UCS C22 Requirements for Virtual Interface Cards Number of...

  • Page 67: Replacing A Cisco Usb Flash Drive

    Enabling a Pre-Loaded Cisco USB Flash Drive Virtual Drive Each of the VDs on the pre-loaded Cisco USB flash drive can be separately enabled or hidden from the host. The default as shipped from the factory is for all VDs to be hidden.
  • Page 68 Booting a Pre-Loaded Cisco USB Flash Drive Virtual Drive When you want to access the Cisco SCU or Cisco HUU software, you boot its VD with a one-time boot option. When you want to boot the hypervisor (HV) VD, you boot it with a permanent boot order selection.

  • Page 69: Cisco Usb Flash Drive Replacement Procedure

    Monitoring and Managing a Cisco USB Flash Drive You can monitor and manage your installed Cisco USB Flash Drive by using the CIMC GUI interface or the CLI interface. See the Cisco UCS C-Series Rack-Mount Server Configuration Guide or the Cisco UCS C-Series Rack-Mount Server CLI Configuration Guide in the documentation roadmap linked below.

  • Page 70: Enabling Or Disabling The Internal Usb Port

    Scroll to USB Port: Internal, press Enter, and then select either Enabled or Disabled from the pop-up Step 5 menu. Step 6 Press F10 to save and exit the utility. Cisco UCS C22 Server Installation and Service Guide 3-36 OL-26646-01...

  • Page 71: Replacing The Supercap Power Module (Raid Backup Unit)

    Connect the cable from the RAID controller to the new SCPM. Replace the top cover. Replace the server in the rack, replace cables, and then power on the server by pressing the Power button. Cisco UCS C22 Server Installation and Service Guide 3-37 OL-26646-01...
  • Page 72 Installing or Replacing Server Components Figure 3-22 Replacing an SCPM SYS FAN1 CPU 1 PCIe 1 SYS FAN2 SYS FAN3 SYS FAN4 PCIe 2 CPU 2 SYS FAN5 PSU 1 SCPM bracket Cisco UCS C22 Server Installation and Service Guide 3-38 OL-26646-01...

  • Page 73: Installing A Trusted Platform Module

    The TPM and the Intel Trusted Execution Technology (TXT) feature must be enabled in the server BIOS. If you have not previously enabled the TXT and TPM, continue with Enabling the Intel Trusted Execution Technology (TXT) Feature For the TPM, page 3-40. Cisco UCS C22 Server Installation and Service Guide 3-39 OL-26646-01...

  • Page 74: Enabling The Intel Trusted Execution Technology (Txt) Feature For The Tpm

    Note so already, set a BIOS administrator password on the Security tab of the BIOS Setup utility. Select the Security tab. Verify that TPM State now says Enabled & Activated. Cisco UCS C22 Server Installation and Service Guide 3-40 OL-26646-01...
  • Page 75 Watch during bootup for the F2 prompt, and then press F2 to enter BIOS setup. Select the Advanced tab, then select Processor Configuration. Verify that the state of these three features is Enabled. Cisco UCS C22 Server Installation and Service Guide 3-41 OL-26646-01...

  • Page 76: Replacing Power Supplies

    Press the Power button to return the server to main power mode. Figure 3-24 Removing and Replacing Power Supplies PCIe 2 PCIe 1 PSU 1 Power supply handle Power supply release lever Cisco UCS C22 Server Installation and Service Guide 3-42 OL-26646-01...

  • Page 77: Appendix

    Table A-1 Physical Specifications Description Specification Height 1.7 in. (4.32 cm) Width 16.9 in. (43.00 cm) Depth 26.0 in. (66.04 cm) Weight (fully loaded chassis) Small Form Factor: 27.78 lbs. (12.60 kg) Cisco UCS C22 Server Installation and Service Guide OL-26646-01...

  • Page 78: Power Specifications

    The power specifications for the two power supply options are listed in the following sections: 450W Power Supply, page A-2 • 650W Power Supply, page A-3 • You can get more specific power information for your exact server configuration by using the Cisco UCS Power Calculator: http://www.cisco.com/assets/cdc_content_elements/flash/dataCenter/cisco_ucs_power_calculator/ 450W Power Supply Table A-2 lists the specifications for each 450W power supply (Cisco part number UCSC-PSU-450W).

  • Page 79: Environmental Specifications

    Appendix A Server Specifications Environmental Specifications 650W Power Supply Table A-3 lists the specifications for each 650W power supply (Cisco part number UCSC-PSU-650W). Table A-3 Power Supply Specifications Description Specification AC input voltage range 90 to 264 VAC self-ranging Low range: 100 VAC to 120 VAC nominal...
  • Page 80 Appendix A Server Specifications Environmental Specifications Cisco UCS C22 Server Installation and Service Guide OL-26646-01...

  • Page 81: Appendix

    Power Cord, 250 VAC 10 A M 2511 Plug Europe SFS-250V-10A-ID Figure B-5 Power Cord, 250 VAC 16A EL-208 Plug South Africa, United Arab Emirates, India SFS-250V-10A-IS Figure B-6 Power Cord, 250 VAC 10 A SI32 Plug  Israel Cisco UCS C22 Server Installation and Service Guide OL-26646-01...
  • Page 82 Power Cord, 250 VAC 13 A NEMA 6-15 Plug, North America CAB-9K12A-NA Figure B-12 Power cord, 125 VAC, 13 A, NEMA 5-15 Plug North America CAB-C13-C14-JMPR Figure B-13 Cabinet Jumper Power Cord, 250 VAC 13 A, C13-C14 Connectors Cisco UCS C22 Server Installation and Service Guide OL-26646-01...

  • Page 83: Ac Power Cord Illustrations

    Cordset rating: 10 A, 250 V/500V Length: 2500mm Connector: Plug: EL 701C EL 206 (IEC 60320/C15) A.S. 3112-2000) Figure B-3 SFS-250V-10A-CN Cordset rating 10A, 250V Plug: (2500 mm) EL 218 (CCEE GB2009) Connector: EL 701 (IEC60320/C13) Cisco UCS C22 Server Installation and Service Guide OL-26646-01...
  • Page 84 Figure B-5 SFS-250V-10A-ID Cordset rating 16A, 250V Plug: (2500mm) EL 208 Connector: EL 701 Figure B-6 SFS-250V-10A-IS Cordset rating 10A, 250V/500V MAX (2500 mm) Connector: EL 701B Plug: (IEC60320/C13) EL 212 (SI-32) Cisco UCS C22 Server Installation and Service Guide OL-26646-01...
  • Page 85 MP232-R Connector: IEC 60320 C15 Figure B-9 CAB-9K10A-UK Cordset rating: 10 A, 250 V/500 V MAX Length: 2500mm Connector: EL 701C Plug: EL 210 (EN 60320/C15) (BS 1363A) 13 AMP fuse Cisco UCS C22 Server Installation and Service Guide OL-26646-01...
  • Page 86 Figure B-11 CAB-N5K6A-NA Cordset rating: 10 A, 250 V Length: 8.2 ft Plug: NEMA 6-15P Connector: IEC60320/C13 Figure B-12 CAB-9K12A-NA Cordset rating 13A, 125V (8.2 feet) (2.5m) Plug: Connector: IEC60320/C15 NEMA 5-15P Cisco UCS C22 Server Installation and Service Guide OL-26646-01...
  • Page 87 Appendix B Power Cord Specifications Supported Power Cords and Plugs Figure B-13 CAB-C13-C14-JMPR, Jumper Power Cord Cordset rating 10A, 250V (686mm) Connector: Plug: HS10S SS10A Cisco UCS C22 Server Installation and Service Guide OL-26646-01...
  • Page 88 Appendix B Power Cord Specifications Supported Power Cords and Plugs Cisco UCS C22 Server Installation and Service Guide OL-26646-01...

  • Page 89: Appendix

    RAID Controller Cabling, page C-17 • LSI MegaRAID Card Beep Codes, page C-19 • Restoring RAID Configuration After Replacing a RAID Controller, page C-20 • For More Information, page C-20 • Cisco UCS C22 Server Installation and Service Guide OL-26646-01...
  • Page 90 Caution RAID controller card at the same time. This is not supported and could result in data loss. Note Dual controllers are not supported. Table C-1 Cisco UCS C22 Small Form Factor RAID Options Maximum RAID Levels Controller Style Drives...

  • Page 91: Mixing Drive Types In Raid Groups

    DRAM in the case of sudden power loss by offloading the cache to the NAND flash. For SCPM replacement instructions, see Replacing the SuperCap Power Module (RAID Backup Unit), page 3-37. Cisco UCS C22 Server Installation and Service Guide OL-26646-01...

  • Page 92: Raid Controller Migration

    Disable SCU storage support in BIOS. Install card. Install cables. HW RAID Not applicable Not allowed Onboard SCU Storage support is Disabled in BIOS Cisco UCS C22 Server Installation and Service Guide OL-26646-01...

  • Page 93: Embedded Raid Controller

    Disabling the Embedded RAID Controller in the BIOS, page C-9 • Launching the LSI Embedded RAID Configuration Utility, page C-9 • Installing LSI MegaSR Drivers For Windows and Linux, page C-9 • Cisco UCS C22 Server Installation and Service Guide OL-26646-01...

  • Page 94: Notes On Supported Embedded Megaraid Levels

    For example, you cannot configure a three-drive array into RAID 0 and RAID 5 VDs. Unlike RAID 0, 1, and 5, you cannot create multiple RAID 10 VDs from the same array. A single RAID 10 VD uses up the entire array. Cisco UCS C22 Server Installation and Service Guide OL-26646-01...

  • Page 95: Installing A Scu Upgrade Rom Module For Embedded Raid Sas Support

    SYS FAN4 SYS FAN4 SYS FAN3 SYS FAN5 SYS FAN5 SYS FAN4 PCIe 2 CPU 2 SYS FAN6 SYS FAN6 SYS FAN5 SCU upgrade ROM header Software RAID 5 key header Cisco UCS C22 Server Installation and Service Guide OL-26646-01...

  • Page 96: Installing A Software Key Module For Embedded Raid 5 Support

    Step 1 Select the Advanced tab, then South Bridge. Step 2 Set Onboard SATA Controller to Enabled. Step 3 Press F10 to save your changes and exit the utility. Step 4 Cisco UCS C22 Server Installation and Service Guide OL-26646-01...

  • Page 97: Disabling The Embedded Raid Controller In The Bios

    SuSE Linux Enterprise Server (SLES) 11 (SP1 and SP2) • This section contains the following topics: Downloading the LSI MegaSR Drivers, page C-10 • Microsoft Windows Driver Installation, page C-10 • • Linux Driver Installation, page C-12 Cisco UCS C22 Server Installation and Service Guide OL-26646-01...

  • Page 98: Downloading The Lsi Megasr Drivers

    See the following URL: http://www.cisco.com/cisco/software/navigator.html Click Unified Computing and Servers in the middle column. Click Cisco UCS C-Series Rack-Mount Standalone Server Software in the right-hand column. Click your model of server in the right-hand column. Click Unified Computing System (UCS) Drivers.

  • Page 99: Embedded Raid Controller C

    Properties. On the Driver tab, click Update Driver to open the Update Device Driver wizard, and then follow the Step 4 wizard instructions to update the driver. Cisco UCS C22 Server Installation and Service Guide C-11 OL-26646-01...

  • Page 100: Linux Driver Installation

    Under Windows, you can use the RaWrite floppy image-writer utility to create disk images from image files. Perform the following steps to build installation diskettes. Download the Cisco UCS C-Series drivers ISO, as described in Downloading the LSI MegaSR Drivers,...
  • Page 101 Under Red Hat Linux and SuSE Linux, you can use a driver diskette utility to create disk images from image files. Perform the following steps to create the driver update disk: Download the Cisco UCS C-Series drivers ISO, as described in Downloading the LSI MegaSR Drivers,...
  • Page 102 Diskettes For Linux, page Then return to Step 4 of this procedure. To install from a virtual floppy disk: Download and save the Cisco UCS C-Series drivers ISO, as • C-10.  described in Downloading the LSI MegaSR Drivers, page Then continue with the next step.
  • Page 103 Diskettes For Linux, page Then return to Step 4 of this procedure. To install from a virtual floppy disk: Download and save the Cisco UCS C-Series drivers ISO, as • C-10.  described in Downloading the LSI MegaSR Drivers, page Then continue with the next step.
  • Page 104 The following message appears: LSI Soft RAID Driver Updates added. At the menu, select the driver update medium and press the Back button. Step 15 Continue and complete the installation process by following the prompts. Step 16 Cisco UCS C22 Server Installation and Service Guide C-16 OL-26646-01...

  • Page 105: Raid Controller Cabling

    3 Embedded RAID SAS connectors  1 Drive backplane on motherboard  (Left to right: SCU_Port 0, SCU_Port 1) 2 SCPM mounting location  4 PCIe risers for RAID controller cards (bracket on chassis floor) Cisco UCS C22 Server Installation and Service Guide C-17 OL-26646-01...

  • Page 106: Cisco Ucs C22 Server Cabling

    Connect mini-SAS cable 2 from connector SAS2 on the card to the drives 5–8 connectors on the Step 3 backplane. Connect the mini-SAS cable 2 SGPIO connector S2 to backplane connector B. Step 4 Cisco UCS C22 Server Installation and Service Guide C-18 OL-26646-01...

  • Page 107: Lsi Megaraid Card Beep Codes

    RAID 6: One or two drives failed. 1 second on, 3 seconds off SPEAKER_HOTSPARE_ENTRY A hot spare drive has completed the rebuild process and has been brought into the array. Cisco UCS C22 Server Installation and Service Guide C-19 OL-26646-01...

  • Page 108: Restoring Raid Configuration After Replacing A Raid Controller

    Full LSI documentation is also available: For basic information on RAID and how to use the LSI utilities, see the documentation at LSI.com: LSI MegaRAID SAS Software User’s Guide (for LSI MegaRAID) • http://www.cisco.com/en/US/docs/unified_computing/ucs/3rd-party/lsi/mrsas/userguide/LSI_MR_SAS_SW_UG.pdf Cisco UCS C22 Server Installation and Service Guide C-20 OL-26646-01...

  • Page 109: Appendix

    The Cisco UCS integration instructions have been moved to the integration guides found here: Cisco UCS C-Series Server Integration with UCS Manager Guides Refer to the guide that is for the version of Cisco UCS Manager that you are using. Cisco UCS C22 Server Installation and Service Guide...
  • Page 110 Appendix D Installation for Cisco UCS Integration Cisco UCS C22 Server Installation and Service Guide OL-26646-01...

Table of Contents