Table of Contents
Advertisement
Chapter 5
Maintaining the Cisco 6400
Installing a Half-Height Node Line Card
To install a half-height NLC in the Cisco 6400 chassis:
Install a full-height NLC carrier in the Cisco 6400 chassis as described in the
Step 1
NLC Carrier in the Chassis" section on page
Hold the NLC vertically, with the module faceplate toward you and backplane connectors away from
Step 2
you. Ensure that the card is right side up by noting the lettering of the faceplate.
Carefully align the upper and lower edges of the NLC with the upper and lower guides in the full-height
Step 3
carrier
Figure 5-25 Installing a Half-Height NLC
Tx and Rx
Tx and Rx
To ensure that the card mates properly with all backplane connector pins, the card length and card
Caution
slots have been designed with very close tolerances. To slide the card into the slot requires gentle
pressure with each hand, at the top and bottom of the faceplate.
Gently slide the NLC into the carrier module until it makes contact with the backplane.
Step 4
Press the upper lever down and the lower lever up at the same time. (This action electrically connects
Step 5
the card to the backplane.)
OL-2133-02
(Figure
5-25).
SUB
SLOT0
OC-3
STM-1
POWER
FAIL
FAULT
MISWIR E
PORT 0
TX
RX
STATUS
PORT 1
TX
RX
STATUS
Port 0
Port 1
POWE R
FAULT
MISWI RE
SUB
SLOT1
5-30.
FANS
FAN
MULTI-
OK
FAILUR E
FAN
FAILUR E
CAUTIO N
When hot swappin g this
fan tray,
removal and replacem ent
must
be done in under two minutes
or
system shutdow n will occur.
1
2
3
4
0A
PRO CES SOR ONLY 0B
NRP
NRP
NRP
OC-3
OC-3
STM-1
NSP
STM-1
NSP
FAIL
FAIL
CON
PORT 0
PORT 0
CON
TX
RX
CON
TX
RX
STATUS
AUX
STATUS
PORT 1
AUX
PORT 1
AUX
TX
RX
TX
RX
STATUS
STATUS
ACT
ACT
ETH
ETH
LNK
LNK
PCMC IA
PCMC IA
CON
CON
AUX
AUX
OC-3
OC-3
STM-1
STM-1
FAIL
Slot 1
FAIL
Slot 1
Slot 0
Slot 0
PORT 0
PORT 0
TX
RX
TX
RX
ACO
STATUS
STATUS
ACO
CRITI CAL
PORT 1
PORT 1
CRITI CAL
TX
RX
MAJO R
TX
RX
MAJO R
STATUS
STATUS
MINO R
MINO R
ALAR MS
ALAR MS
STATU S
STATU S
FAIL
STATU S
STATU S
STATU S
FAIL
FAIL
FAIL
FAIL
PRO CES SOR ONLY
Cisco 6400 Hardware Installation and Maintenance Guide
Replacing an NRP Module
"Installing a Full-Height
5
6
7
8
OC-3
OC-3
OC-3
STM-1
STM-1
NRP
STM-1
FAIL
FAIL
FAIL
PORT 0
PORT 0
PORT 0
TX
RX
TX
RX
TX
STATUS
RX
STATUS
STATUS
PORT 1
PORT 1
PORT 1
TX
RX
TX
RX
TX
STATUS
RX
STATUS
STATUS
SUB
SLOT
0
CON
AUX
OC-3
OC-3
OC-3
STM-1
STM-1
STM-1
FAIL
FAIL
FAIL
PORT 0
PORT 0
PORT 0
TX
RX
TX
RX
TX
STATUS
RX
STATUS
STATUS
PORT 1
PORT 1
PORT 1
TX
RX
TX
RX
STATUS
TX
RX
STATUS
STATUS
SUB
SLOT
1
STATU S
FAIL
5-31
Advertisement
Table of Contents
