Download
Share
Print this page
Makita VC3211M Technical Manual
  1. Manuals
  2. Brands
  3. Makita Manuals
  4. Vacuum Cleaner
  5. VC3211M
  6. Technical manual

Makita VC3211M Technical Manual

Hide thumbs Also See for VC3211M:

Advertisement

Quick Links

Download this manual See also: Instruction Manual
T
ECHNICAL INFORMATION
Model No.
Description
C
ONCEPT AND MAIN APPLICATIONS
Model VC3211M is a Wet & Dry vacuum cleaner developed
based on Model VC3210L.
This product is approved for Dust Class M in accordance with
the EU standard.
Its main benefits are:
• New automatic self-cleaning filtration system of our unique design
• Power tool activation
• 32 Liter stainless steel tank
• High maneuverability and easy mobility
*The same advantage as Model VC3210L
This model is also available with cleaning set as VC3211MX1.
(See "Standard equipment" for what the cleaning set includes.)
S
pecification
Voltage (V)
110
230
240
Wet/Dry type
Power tool activation
Dust class in accordance with the EU standard
Max. sealed suction: kPa
Max. air flow: m³/minute
Tank capacity: L
Noise: dB
Variable suction power control by dial
Protection from electric shock
Power supply cord: m (ft)
Weight according to EPTA-Procedure 01/2003*
*1: with Hose complete 28-3.5 *2: with Hose complete 38-2.5
*3: with Poly bag 800x650
S
tandard equipment
For
All models:
Hose complete 28-3.5 set .......... 1
(incl. Front cuff 38)
Front cuff 22 .............................. 1
Front cuff 24 .............................. 1
Belt hook ................................... 1
Hose band .................................. 1
Cap ............................................ 1
Poly bag 800x650 ...................... 1
Poly bag set ............................... 1
(incl. 10 pcs of Poly bag 800x650)
Note: The standard equipment for the tool shown above may vary by country.
VC3211M
Vacuum Cleaner
*
*
*
Current (A)
Cycle (Hz)
10.0
50/60
4.8
50/60
4.6
50/60
Water
Dust
3
For
VC3211MX1 only:
Cleaning set..................... 1
Includes one each of:
-Hose complete 38-2.5
-Straight pipe
-Bending pipe
-Nozzle assembly
-Corner nozzle
Continuous Rating (W)
Input
1,050
1,050
1,050
Wet & Dry
2.0*
Grounding
5.0 (16.4)
: kg (lbs)
16.9 (37.3)
O
Hose complete 28-2.5/ 28-3.5/
Front cuff 22/ 24/ 38
Filter bag set (5pcs/set)
Poly bag set (10 pcs/set)
Powder filter, Damper, Prefilter
Straight pipe, Bending pipe, Nozzle assembly,
Corner nozzle, Anchor nozzle, Round brush,
Cap, Cleaning set, Nozzle for wet application,
Belt hook, Hose band
W
Dimensions: mm (")
Length (L)
Width (W)
Height (H)
Max. Output (W)
Output
---
---
--
Yes
M
22.0
/ 3.5*
1
2
27
32
73
Yes
ptional accessories
28-5.0/ 38-2.5/ 38-5.0
PRODUCT
P 1/18
H
L
552 (21-3/4)
398 (15-5/8)
685 (27)
---
---
---

Advertisement

loading

Related Manuals for Makita VC3211M

Summary of Contents for Makita VC3211M

  • Page 1 VC3211M Description Vacuum Cleaner ONCEPT AND MAIN APPLICATIONS Model VC3211M is a Wet & Dry vacuum cleaner developed based on Model VC3210L. This product is approved for Dust Class M in accordance with the EU standard. Its main benefits are: •...

  • Page 2: Necessary Repairing Tools

    M5x60 Pan head screws through Endbell and Field into Base [2] LUBRICANT/ADHESIVE APPLICATION Apply Makita grease N.No.2 to the following portions designated by black triangle to protect parts and product from unusual abrasion.. (Fig.1) Apply ThreeBond 1215 to Rubber ring 120 and Seal ring.
  • Page 3 P 3/18 epair [3] DISASSEMBLY/ ASSEMBLY [3]-1. Motor section DISASSEMBLING (1) Unlock two hooks to separate Motor section from Tank section. (Fig. 2) (2) Raise Grip and open Base hook, then remove nine 4x35 Tapping screws to remove Base grip and Cowling complete from Separator complete.
  • Page 4 P 4/18 epair [3] DISASSEMBLY/ ASSEMBLY [3]-1. Motor section (cont.) DISASSEMBLING (7) Take two Closed end splices out of the splice storage compartment to allow the lead wire of each of two Lead units to have slack in it. (Fig. 7) (8) With the lead wire of Lead units slack, remove Separator complete from Tank cover complete.
  • Page 5 P 5/18 epair [3] DISASSEMBLY/ ASSEMBLY [3]-1. Motor section (cont.) DISASSEMBLING (10) Disconnect Carbon brushes from the commutator of Armature assembly by moving the tail end of the spiral spring of each Brush holder as shown in Fig. 10. Note: No need to remove Carbon brushes in this step. (11) Unscrew M4x12 Pan head screw that fastens Brush holder to Endbell, then remove Receptacle terminal from the terminal of Brush holder, and then remove Brush holder together with Carbon brush.
  • Page 6 P 6/18 epair [3] DISASSEMBLY/ ASSEMBLY [3]-1. Motor section (cont.) ASSEMBLING (1) Assemble the parts shown in Fig. 14. Note: Loosely tighten M8 Hex nut to Armature shaft. (2) Install Fan cover onto the assembly you made in step (1) as follows: 1.
  • Page 7 P 7/18 epair [3] DISASSEMBLY/ ASSEMBLY [3]-1. Motor section (cont.) ASSEMBLING (5) Make sure that Wave washer 20 is placed in the bearing chamber of Endbell, insert Armature assembly into Endbell. (6) While pressing the bearing chamber of Endbell straight down so that Wave washer 20 is approximately level, alternately tighten the two M5x60 Pan head screws with a manual screwdriver until they are seated.
  • Page 8 Spindle with those of Cam’s hole. Note: Do not forget to place DC motor seal between Separator complete on Tank cover complete. Note: Apply Makita grease N.No.2 to the gear chamber of Gear case to prevent Spindle assembly from falling off from DC motor unit.
  • Page 9 P 9/18 epair [3] DISASSEMBLY/ ASSEMBLY [3]-2. Inner cover DISASSEMBLING (1) Turn the assembly of Inner cover and Tank cover complete upside down, then raise Lock lever to remove two Pre-filters. (Fig. 25) (2) Remove eight 4x35 Tapping screws that fasten Inner cover to Tank cover complete. (Fig. 26) Three of the eight screws are used also to fasten Protector to Inner cover.
  • Page 10 P 10/18 epair [3] DISASSEMBLY/ ASSEMBLY [3]-2. Inner cover (cont.) ASSEMBLING Assemble by reversing the disassembly procedure. Note: • When installing Seal ring onto Tank cover complete, put the protruding portion of the ring in the depressed portion of Tank cover complete, then apply ThreeBond 1215 to the portion as shown on the left of Fig. 29. •...
  • Page 11 2. Put 1R275 in the groove of the plastic portion of new Caster 75. 3. Hit 1R275 with a plastic hammer. *You can use any kind of grease such as Makita grease N No.2. Caster 75 1R275 plastic portion of new Caster 75...
  • Page 12 P 12/18 epair [3] DISASSEMBLY/ ASSEMBLY [3]-5. Bumper Fig. 36 DISASSEMBLING Pry Bumper off from Tank with a slotted screwdriver. (Fig. 36) ASSEMBLING Assemble by reversing the disassembly procedure. Note: Make sure that there is no gap between Bumper and Base. Bumper Tank [3]-6.

  • Page 13: Circuit Diagram

    P 13/18 ircuit diagram Fig. D-01 AC motor Color index of lead wires' sheath Black Blue White Purple Gray Brush holder Yellow Green Field Orange Brush holder DC motor Band (cable tie) Strain relief Vinyl tube red marking Line filter (if used) black or Terminal block...
  • Page 14 P 14/18 ircuit diagram Fig. D-02 Receptacle Country Back view Part No. Front view showing where Terminals C1, C2 and C3 are located C03 to Green and Yellow wire C01 to C02 to European countries, Orange wire Purple wire 655117-0 etc.

  • Page 15: Wiring Diagram

    P 15/18 iring diagram 1. AC motor unit Fig. D-03 AC motor unit, Field lead wire viewed from top to Controller Fix two Field lead wires to each Brush holder in these lead wire holders. Brush holder Brush holder Field lead wire to Controller Fig.
  • Page 16 P 16/18 iring diagram 1. AC motor unit (cont.) Fig. D-06 Be careful not to pinch the pig tail wire of Carbon brush between Motor cover Motor cover and Brush holder. pig tail wire of Carbon brush Brush holder Fig. D-07 Tank cover complete, Install AC motor unit viewed from top...
  • Page 17 P 17/18 iring diagram 2. Wiring in Separator complete Fig. D-08 Put the following Lead wires between these ribs: • Power supply cord’s lead wire connected to Controller • Controller’s lead wires connected to DC motor • Buzzer circuit’s lead wires •...
  • Page 18 P 18/18 iring diagram 2. Wiring in Separator complete Fig. D-09 Do not place the slack of Lead wires Do not place the slack of Lead wires on this portion. on these ribs. Place Lead wires and Vinyl tube between the boss and the inside wall boss of Separator complete.