Specifications; Specific Safety Rules - Makita 4334d Instruction Manual

ENGLISH
1 Button
2 Battery cartridge
3 Lever
4 Lock-off button
5 Switch trigger
6 Speed adjusting dial
7 Base
8 Anti-splintering device
9 Screw
10 Plastic base plate
11 Hex wrench

SPECIFICATIONS

Model
Length of stroke .................................................... 26 mm
Max. cutting capacities
Wood ............................................................... 135 mm
Mild steel ........................................................... 10 mm
Aluminum ........................................................... 20 mm
Strokes per minute ....................................... 500 – 2,800
Overall length ..................................................... 281 mm
Net weight .............................................................. 3.3 kg
Rated voltage ...................................................D.C. 18 V
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
As a result of the extensive accessory and saw blade
program, the tool can be used for many purposes and is
very well suited for curved or circular cuts.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER & BATTERY CARTRIDGE
1. Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using bat-
tery.
2. Do not disassemble battery cartridge.
3. If operating time has become excessively
shorter, stop operating immediately. It may result
in a risk of overheating, possible burns and even
an explosion.
4. If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
5. Always cover the battery terminals with the bat-
tery cover when the battery cartridge is not
used.
6. Do not short the battery cartridge:
(1) Do not touch the terminals with any conduc-
tive material.
(2) Avoid storing battery cartridge in a container
with other metal objects such as nails, coins,
etc.
Explanation of general view
12 Bolt
13 Guide rule
14 Threaded knob
15 Circular guide
16 Pin
17 Vacuum head
18 Blade installing lever
19 Blade holder
20 Clamp
21 Roller
22 Slot
4334D
7.
8.
9.
SAVE THESE INSTRUCTIONS.
Tips for maintaining maximum battery life
1.
2.
3.
4.
ENC004-1

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adher-
ence to jig saw safety rules. If you use this tool
unsafely or incorrectly, you can suffer serious
personal injury.
1.
2.
23 Blade
24 Hold blade against blade holder
25 Cutting line
26 Base securing lever
27 Dent mark
28 Slot
29 Graduations
30 Limit mark
31 Screwdriver
32 Brush holder cap
(3) Do not expose battery cartridge to water or
rain.
A battery short can cause a large current flow,
overheating, possible burns and even a break-
down.
Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50°C (122°F).
Do not incinerate the battery cartridge even if it
is severely damaged or is completely worn out.
The battery cartridge can explode in a fire.
Be careful not to drop or strike battery.
Charge the battery cartridge before completely
discharged.
Always stop tool operation and charge the bat-
tery cartridge when you notice less tool power.
Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
Charge the battery cartridge with room tempera-
ture at 10°C – 40°C (50°F – 104°F). Let a hot bat-
tery cartridge cool down before charging it.
Charge the Nickel Metal Hydride battery car-
tridge when you do not use it for more than six
months.
Hold power tools by insulated gripping sur-
faces when performing an operation where
the cutting tool may contact hidden wiring or
its own cord.
Contact with a "live" wire will make
exposed metal parts of the tool "live" and shock the
operator.
Use clamps or another practical way to
secure and support the workpiece to a stable
platform.
Holding the work by hand or against your
body leaves it unstable and may lead to loss of con-
trol.
GEB016-1
7