Toshiba Strata DK 280 Installation Manual page 447

Program 1 O-2
-System Assignments, Part 2 of 3
SELECT =
2
1 -C Buttons/LEDs
Light LEDs as defined by the table below.
ALL LEDs with an "X" should be lit when YOU finish.
BUTTON/
LED X
LED On
LED Off
20 Padded DTMF Tone Return When Dialing DTMFlNo DTMF Per Prog 1 O-2, LED 11
I
19s
I
1
1 External Conference Amp Connected to PEKU 1 No External Amplifier Connected ~ 1
I
186 1 External Conference Amp Connected to PEKU No External Amplifier Connected
I
17 "TRNS" Soft Key-Immediate "TRNS" Soft Key-Normal
16
1
Executive Override Warning Tone/ON Executive Override Warning Tone/OFF
15s
1
External Page included with All Call Page
Not Included
14
13
12
11
103
093
088
1 Privacy Override/Attendant/Supervised Loop Warning Privacy/Attendant Supervised Loop
Tone/ON
Override Warning Tone/OFF
Send Auto Callback Camp-on Tone2 No Callback Tone
CO Line 3 min Beep Tone No Beep Tone
No DTMF Tone Return When Dialing5 DTMF Tone Return When Dialing
BGM connected to PESU, Circuit 8 EKT connected to PESU, CKT 8
BGM connected to PEKU, Circuit 3
EKT connected to PEKU, CKT 3
Elapsed Time Display 1 min. After Access or Answer a
Elapsed Time Display 15 sec. After Access
CO line
or Answer a CO Line
I
074 1 Standard Tel. CO Ring per Prog. 1 O-l, LED 06 Standard Tel. CO Ring Distinctive
I
06
05
VM ID Code DTMF Signal Time 80 ms
160 ms
047 MW cancel from VM: RS-232 or dial # 6 4 +
[DN]
MW cancel from VM: Automatic When
Answer
I
I
03 3 Ringing Modes
2 Ringing Modes
02
1 Hunt/C.F. override from DSS console's phone Hunt/C.F. override from DSS console
01 Tone First (from DSS Console) Voice First (from DSS Console)
I
I I
I
1
Notes: DK0108
1. Initialized data lights LEDs 0.2, 14, 15 and 16.
2. Called party receives notification tone when calling party activates Auto Call Back.
3. BGM connected to the PEKU or PEW will be sent to electronic and digital telephone speakers and external page (optional). To
assign the BGM PCB slot number, see Program 19- 1.
4. The ring pattern for standard telephone, distinctive ring on incoming trunk calls is: 0.2 sec. on/O.4 sec. off, 0.2 sec. on /3.4 sec. off;
intercom ring is a/ways 1 sec. on, 3 sec. off. This does not apply to VM Ports (Program 37, LED 17 on) which are a/ways standard
ring.
5. Deletes DTMF tones returned to digital and electronic telephones
when dialing from dial
digits from callers that are call forwarded to voice mail. This does not affect the actual
D 5!
ad or speed dialing; also deletes auto dial
MF tones sent out to trunks or voice mail
devices.
IMPORTANT !
6. LED 18 and 19 should be OFF unless external amplifiers are used for Two-CO line/Station Conference (see Program 10-3). If LED
18 and 19 are ON, the station may be unbalanced and receive HUM if external amplifier with Auto-Gain-Control is not connected. If
volume is tow on Two CO line conference because of line loss, if is recommended to test conference with LED 18 and 79 ON.
If
there is no HUM noise and volume improves, keep LED 18 and 79 ON.
7. LED 04 should be on for DTMF or RS-232 VM integration - also see Program 31.
8. "Elapsed time of call" will replace CO line Name, DNIS, ANI, or Caller ID information on telephone LCDs, 1 min. or 15 sec. after an
incoming call is answered.
General Notes:
I
.
External speakers and all electronic and digital telephones are paged by dialing: Intercom or Directory Number [DN] + #39. The
All Call Page (AC) button is used to page all digital and electronic telephones only; external speakers are not included when using
the button.
.
PESU/PEKU can be in any universal slot assigned in Program 19- 1
February 1996