Toshiba Strata DK 280 Installation Manual page 375

(PDIU-DS) connected to the digital port. Each
RPCI-DI or PDIU-DI uses the same digital port as
the telephone it is attached to. If an RPCI-DI is
used in the Application Program Interface (API)
mode only, and not the Data Switching mode, this
option is not applicable. Each PDIU-DS requires a
separate digital port.
n
AT Commands and Result Codes, LED 02-If
the RPCI or DIU must respond to AT commands
and return result codes in the Data Switching
command mode, this LED should be lit. RPCI/DIU
"AT" dialing commands and "result" codes are
listed in the RPCI-DI and "Data Interface User
Guide" in the Operating Procedures section of this
manual. If LED 02 is not lit, the RPCVDIU will only
respond to AT dialing commands (ATDT, ATD,
and ATDD) and will not return result codes. If the
DIU is connected to a terminal or a personal
computer with communication software, LED 02
should be ON
If the DIU is connected to a modem, LED 02
should be ON. If the RPCI/DIU is connected to a
printer, LED 02 should be OFF. If an RPCI-DI is
used in the Application Program Interface (API)
mode only, and not the Data Switching mode, this
option is not applicable.
n
RPCVPDIU-DS to Modem Connection, LED
03-If a PDIU-DS is connected to the digital port,
identify whether the RPCVPDIU-DS is connected
to a modem (LED ON) or not connected to a
modem (LED OFF). If not connected to a modem
(LED OFF), the connected device can be a DCE
or DTE. This option is not necessary for
RPCVPDIU-Dls, because they are not normally
connected to modems.
H PDIU-DI or PDIU-DS Connection, LED 04-Light
this LED if a PDIU-DS is connected to the digital
port; leave OFF, if a RPCI-DI or PDIU-DI is
connected. If a RPCVRPCI-DI is connected, the
digital telephone supporting it may require the
Data Call (DATA), Data Release (DRLS),
and/or Modem buttons assigned in Program 39.
If an RPCI-DI is used in the Application Program
Interface (API) mode only, and not the Data
Switching mode, LED 04 should be off.
q
Auto Pause Behind PBX, LED 05-If the system
CO lines are connected to a PBX, Centrex, or a
Central Office that is slow to return dial tone after
seizure, light this LED to insert a pause before and
after the PBX or Centrex access code is dialed by
January 1996
9-l 5
w
w
w
H
w
the DIU or RPCI. Also, light LED 05 to
automatically insert a pause before network
telephone numbers are autodialed by DlUs or
RPCls.
Note:
The pause length is set in Program 12-3, and
lines behind PBX/Centrex are assigned in
Programs 42-O and 42- 1 - 8.
DTR Pulse, LED 06-LED 06 should be off for all
PDIU-DS, RPCI-Dls, or PDIU-Dls. (Refer to
Chapter g--Peripheral Installation for more PDIU-
DS/modem pool information).
RPCI-DI Caller ID and ANI to PC Option, LED
'
10-Caller ID and ANI information that is sent to a
telephone can be sent, or blocked, from the
telephone's RPCI-DI, RS-232 output. If Caller ID
and ANI information should be sent from the
RPCI-DI to the Personal Computer to which it is
connected, turn LED 10 ON; if this information
should not be sent to the PC, turn LED 10 OFF.
This option does not apply to PDlUs because they
can not send ANI, Caller ID, or DNIS numbers.
RPCI-DI DNIS to PC Option, LED ll-DNIS
Number or NAME tag information that is sent to a
telephone can be sent, or blocked, from the
telephone's RPCI-DI, RS-232 output. If DNIS
information should be sent from the Telephone's
RPCI-DI to the Personal Computer to which it is
connected, turn LED 11 ON; if this information
should not be sent to the PC, turn LED 11 OFF.
Data Security Groups, LEDs 17 - SO-Data
security groups can be set to block data calls
between RPCVDIUs. RPCVDIUs can only make
data calls to RPCI/DIUs in the same security
group. LEDs 17 - 20 assign the RPCVDIU to the
appropriate security group: light LED 17 for Group
1; LED 18, for Group 3; LED 19, for Group 2; and
LED 20, for Group 4. If an RPCI-DI is used in the
Application Program Interface (API) mode only,
and not the Data Switching mode, this option is
not applicable.
Typical LED settings for Program 20-
+ RCPI-DVPDIU-DI Connected to a terminal or
personal computer-LEDs 01, 02, 05, and 17
ON; all other LEDs OFF.
+ PDIU-DS Connected to a Printer-LEDs 01,
04, and 17 ON; all other LEDs OFF.