Typical Configuration Guide For System Jumpers Or Switches - HP 5501A Operating And Service Manual

Table
5-3.
Typical Configuration Guide for System jumpers or Switches
* A 10760A Counter card must
be
addressed t o correspond t o each 1 0 7 6 3 A card (e.g., X,
Y ,
and
Z
for this example).
Set Up
Address
Set Up
Next
Address
Deddpath
Inch
NOR
First
O n e Axis
E R R
Stop/Go
A/UP
B/DWN
TEST/
RUN
800 K H z /
1.6
MHz
Axis
Select
Weight
Examples
X10=(9+1) 1 pm
i l 0 0 pin)
I
I I I I I 1 I I I I
X100=(99+1)10 pm
MSB
10 pm
LSB
1000 pin,
- 1
1 1 1
( : : ; : i n ) (1000
1 1 1
- 1
i
(Master)
X-Axis
(Labeled
on
Card)
Already set at factory but may
have moved in shipment.*
Already set at factory but may
have moved in shipment.
Y
'
1 7 1
S67
Set up by user. See paragraph 5.10.2
or 10763A English/Metric manual
for details.
This jumper is installed a s the
resolution is English. Remove for
Metric units.
This jumper is installed a s the
resolution is normal. Remove for
X10.
This jumper is removed a s this is the
master card in the system.
This jumper installed i i only one axis
system. This jumper is removed.
Installed in the GO position.
Set by user. Set to UP arbitrarily.
Set by user. Set to DWN arbitrarily.
Run.
Set up by user. Set to 1 . 6 M H z
arbitrarily.
Same a s this axis.
ABCXYZ
Set up by user. Determines reso-
lutiurl u i pulses uut.
Basic resolution
I S
. I pm
Resolution Switch Settings
Y-Axis
(Labeled
on
Card)
Already set at factory but may
have moved in shipment.*
' f
:
W S . 7
Already set at factory buy may
have moved in shipment.
Set up by user. See paragraph 5.10.2
or 10763A English/Metric manual
ior details.
This jumper is installed a s the
resolution is English. Remove for
Metric units.
This jumper is installed a s the
resolution is normal. Remove for
XIO.
This jumper i s inserted since
X-axis is the master card.
This jumper is removed.
Installed in the G O position.
Set by user. Set to UP
arbitrarily.
Set by user. Set to DWN
arbitrarily.
Run.
Set up by user. Set to 1.6 M H z
arbitrarily.
Same a s this axis.
1 1 1 1 1 1 1 1 l s i l
ABCXYZ
Set up by user. Determines reso-
luliurl u l pulse5 out.
Basic resolution is . l pm
Resolution Switch Settings
Z-Axis
(Labeled
on
Card)
Already set at factory but may
have moved in shipment.*
Z
"
1
S67
Already set at factory but may
have moved in shipment.
Set up by user. See paragraph 5.10.2
or 10763A English/Metric manual
ior details.
This jumper is installed a s the
resolut~on
i s
English. Remove for
Metric units.
This jumper is installed a s the
resolution is normal. Remove for
X10.
This jumper is inserted since
X-axis i s the master card.
This jumper is removed.
Installed in the
GO
position.
Set by user. Set to UP arbitrarily.
Set by user. Set to DWN arbitrarily.
Run.
Set up by user. Set to 1.6 MHz
arbitrarily.
Same a s this axis.
A B C X Y Z
Set up by user. Determines reso-
lution of pulse out.
Basic resolution is .I pm
Resolution Switch Settings