Operation And Settings; Projecting Image - JVC 0210TTH-SW-VP Instructions Manual

Operation and Settings

Projecting Image

If setting for this projector is not completed, refer to User
Settings Menu (A Page 33) upon turning on the power
and configure the settings accordingly.
Once the basic settings are configured, this projector can
be used by simply performing the following operation
procedures.
PREPARATION:
● Remove the lens cap.
● Connect this projector to the computer. (A Page 21, 23)
● Connect the LAN cable. (A Page 24)
1
Set this projector to the standby mode, and
display the main menu
● Refer to Turning On the Main Power
(A Page 25), and steps 4 to 6 of Assigning a
static IP address (A Page 28).
● The [STANDBY/ON] indicator lights up in red.
2
Click the ON button under the Power
item of the main menu to project the image
● The power of this projector turns on, and formatting
is done taking a few minutes. A gray image will be
displayed during formatting. The projected image
appears once formatting ends.
● The [STANDBY/ON] indicator lights up in green.
Power
Main
Image
ON OFF
Setting
Lamp Mode
Convergence
Both Lamp1
Lens
Option
Lamp Information
Lamp Status
1 ok 10h54m
2 ok 11h58m
Signal Status
DVI Rate(Hz) Pixel H
1 60.00
2
3 60.00
4
NOTE:
● You can also turn on the power by pressing the
[OPERATE I/B] button on the projector unit for more
than one second.
● The image may flicker for a few seconds immediately
after projection starts. This is not a malfunction.
● After the lamp lights up, it takes about 1 minute or
longer for the brightness of the video image on the
screen to stabilize.
host PJ-1
user: root
Logout
Warning Status
PROJECTION None
Lamp2 Auto
Hide
Time
OFF ON
Temperature
Pixel V Link
Lamp
2048 2400 Dual
26.8 deg.C
Outside
2048 2400 Dual
26.3 deg.C
Inside
34.0 deg.C
3
Adjust the zoom ratio (screen size) (when
zoom lens is in use)
You can adjust the focus using the Zoom item of the
Lens menu.
Zoom Focus
Main
+
w
Image
Setting
Convergence
Lens
_
Option
T
Test Pattern
OFF
To enlarge the screen size:
Press the W (Wide) end of Zoom
To reduce the screen size:
Press the T (Tele) end of Zoom
NOTE:
● The screen size changes each time you click on the
inner buttons ( / ). (Fine control)
The outer buttons ( / ) change the screen size when
they are depressed. (Coarse control)
4
Adjust the position of the projection screen
You can adjust the focus using the Shift item of the
Lens menu.
To shift the image upward:
Press the U end of Shift
To shift the image downward:
Press the D end of Shift
To shift the image rightward:
Press the R end of Shift
To shift the image leftward:
Press the L end of Shift
NOTE:
● When a zoom lens is used, the adjustment range for
lens shift is between 0 % to ±50 % in the vertical
direction, and between 0 % to ±25 % in the horizontal
direction (during single-screen display).
When a short focal length lens is used, the adjustment
range for lens shift is between 0 % to ±15 % in the
vertical direction, and between 0 % to ±5 % in the
horizontal direction (during single-screen display).
(A Page 16)
● The position changes each time you click on the inner
buttons ( / ). (Fine control)
The image shifts when the outer buttons ( / ) are
depressed. (Coarse control)
● The lens shift feature does not function if the lens
mechanism is secured.( A Page 16 Lens Fixation
Mechanism )
host PJ-1
user: root
Logout
Shift
U
L R
D
OFF
SET