Table of Contents
Advertisement
Failure to maintain adequate distance from trees, walls,
and other barriers may result in injury as the machine
backs up during operation if the operator is not attentive
to the surroundings. Only operate the unit in areas where
there is sufficient clearance for the operator to safely
maneuver the product.
•
Before digging, have the area marked for underground
utilities, and do not dig in marked areas.
•
Locate the pinch point areas marked on the machine and
keep hands and feet away from these areas.
•
Lightning can cause severe injury or death. If lightning
is seen or thunder is heard in the area, do not operate
the machine; seek shelter.
Slope Operation
Slopes are a major factor related to loss-of-control and
tip-over accidents, which can result in severe injury or death.
All slopes require extra caution.
•
Do not operate the machine on hillsides or slopes
exceeding the angles recommended in the following table.
Front Facing
Rear Facing Uphill Side Facing Uphill
Uphill
12°
Note: See also the Slope Indicator (page 7).
•
Operate up and down slopes with the front end of
the machine uphill.
•
Remove obstacles such as rocks, tree limbs, etc. from the
work area. Watch for holes, ruts, or bumps, as uneven
terrain could overturn the machine. Tall grass can hide
obstacles.
•
Use only Toro-approved accessories. Accessories can
change the stability and the operating characteristics
of the machine. Warranty may be voided if used with
unapproved accessories.
•
Keep all movements on slopes slow and gradual. Do not
make sudden changes in speed or direction.
•
Avoid starting or stopping on a slope. If the machine
loses traction, proceed slowly, straight down the slope.
•
Avoid turning on slopes. If you must turn, turn slowly
and keep the heavy end of the machine uphill.
•
Do not operate near drop-offs, ditches, or embankments.
The machine could suddenly turn over if a track goes
over the edge of a cliff or ditch, or if an edge caves in.
•
Do not operate on wet grass. Reduced traction could
cause sliding.
•
Do not park the machine on a hillside or slope without
lowering the grinder to the ground and chocking the
tracks.
18°
16°
Maintenance and Storage
•
Disengage the hydraulics, lower the grinder, stop the
engine, and remove the key. Wait for all movement to
stop before adjusting, cleaning, or repairing.
•
Clean debris from the grinder, drives, mufflers, and engine
to help prevent fires. Clean up oil or fuel spillage.
•
Let the engine cool before storing and do not store near
flame.
•
Do not store fuel near flames or drain indoors.
•
Park the machine on level ground. Never allow untrained
personnel to service the machine.
•
Use jack stands to support components when required.
•
Carefully release pressure from components with stored
energy.
•
Disconnect the battery or remove the spark plug wires
before making any repairs. Disconnect the negative
terminal first and the positive last. Reconnect positive
first and negative last.
•
Keep hands and feet away from moving parts. If possible,
do not make adjustments with the engine running.
•
Keep all parts in good working condition and all hardware
tightened. Replace all worn or damaged decals.
•
Keep nuts and bolts tight. Keep equipment in good
condition.
•
Never tamper with safety devices.
•
Keep the machine free of grass, leaves, or other debris
build-up. Clean up oil or fuel spillage. Allow the machine
to cool before storing.
•
Use extra care when handling gasoline and other fuels.
They are flammable and vapors are explosive.
– Use only an approved container.
– Never remove the gas cap or add fuel when the
engine is running. Allow the engine to cool before
refueling. Do not smoke.
– Never refuel the machine indoors.
– Never store the machine or fuel container inside
where there is an open flame, such as near a water
heater or furnace.
– Never fill a container while it is inside a vehicle, trunk,
pick-up bed, or any surface other than the ground.
– Keep container nozzle in contact with the tank during
filling.
•
Stop and inspect the equipment if you strike an object.
Make any necessary repairs before restarting.
•
Use only genuine Toro replacement parts to ensure that
original standards are maintained.
•
Battery safety:
– Charge batteries in an open, well ventilated area, away
from spark and flames. Unplug the charger before
connecting or disconnecting it from the battery. Wear
protective clothing and use insulated tools.
5
Advertisement
Table of Contents
