Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Operator's Manual
Advertisement
Table of Contents
Related Manuals for Toro 22615
Summary of Contents for Toro 22615
- Page 1 Form No. 3386-283 Rev A SGR-13 Stump Grinder Model No. 22615—Serial No. 314000001 and Up Model No. 22615G—Serial No. 314000001 and Up Model No. 32611—Serial No. 314000001 and Up *3386-283* A Register at www.Toro.com. Original Instructions (EN)
-
Page 2: Introduction
State of California to cause cancer, birth defects, You may contact Toro directly at www.Toro.com for product or other reproductive harm. and accessory information, help finding a dealer, or to register your product. -
Page 3: Table Of Contents
Safety This manual uses 2 words to highlight information. Important calls attention to special mechanical information and Note emphasizes general information worthy of special Improper use or maintenance by the operator or owner attention. can result in injury. To reduce the potential for injury, comply with these safety instructions and always pay attention to the safety alert symbol , which... -
Page 4: Maintenance And Storage
– Never refuel or drain the machine indoors. Failure to maintain adequate distance from trees, walls, and other barriers may result in injury as the machine • Check that the operator presence controls, safety switches, backs up during operation if the operator is not attentive and shields are attached and functioning properly. -
Page 5: Safety And Instructional Decals
Stop and inspect the equipment if you strike an object. Make any necessary repairs before restarting. • Use only genuine Toro replacement parts to ensure that original standards are maintained. Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. -
Page 6: Product Overview
Product Overview 119-4692 1. Warning—stop the engine; use both hand holds to lift the grinder. Figure 3 1. Throttle lever 8. Cutting wheel 2. Hour meter 9. Belt cover 3. Cyclone air filter 10. Lift 4. Choke 11. Fuel Cap 5. -
Page 7: Specifications
2. Engaged throttle position its capabilities. Contact your Authorized Service Dealer or position Distributor or go to www.Toro.com for a list of all approved attachments and accessories. Parking Brake The parking brake holds the left wheel from turning to secure the machine and for easy movement of the machine from side to side when grinding the stump. -
Page 8: Operation
Operation DANGER In certain conditions, gasoline is extremely Note: Determine the left and right sides of the machine flammable and highly explosive. A fire or explosion from the normal operating position. from gasoline can burn you and others and can damage property. -
Page 9: Checking The Engine-Oil Level
because the fuel system could be damaged. Do not mix 6. Wipe up any gasoline that may have spilled. oil with gasoline. Checking the Engine-oil Level Using Stabilizer/Conditioner Service Interval: Before each use or daily Use a fuel stabilizer/conditioner in the machine to provide 1. -
Page 10: Starting And Stopping The Engine
Starting and Stopping the WARNING Engine Grinding a stump will throw wood chips, soil, and other debris into the air which could injure you or bystanders. Starting the Engine • Always wear eye protection and a hard hat when 1. Move the fuel valve to the Open position, all the way using the machine. - Page 11 Figure 9 6. Raise the cutting wheel, release the parking brake, and move the machine forward a few inches. Set the parking brake. 7. Repeat steps 5 and 6 until you have completely removed the stump (E through H in Figure 9). 8.
-
Page 12: Maintenance
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Important: The machine may be tipped backward or by gasoline draining into the crankcase. Should this on its side to facilitate access for cleaning or service, happen, perform an extra oil change on the engine. -
Page 13: Engine Maintenance
Engine Maintenance Servicing the Air Cleaner Service Interval: Before each use or daily The cyclone air filter collects the largest contaminant particles, which collect in the container. When you can see a layer of dirt at the bottom of the container, clean the cyclone housing, air channels, and air intake screen. -
Page 14: Servicing The Engine Oil
Servicing the Engine Oil Cleaning the Sediment Cup Service Interval: Every 100 hours Note: Change the oil more frequently when the operating conditions are extremely dusty or sandy. Yearly or before storage Oil Type: Detergent oil with an API service of SJ or higher. Underneath the fuel valve is a sediment cup to catch dirt in the fuel. -
Page 15: Brake Maintenance
Brake Maintenance 2. Pull the wire off the spark plug (Figure 15). Adjusting the Parking Brake 1. Loosen the set screw on side of brake lever knob. Turn the knob clockwise to tighten the brake; adjust counter clockwise to loosen the brake. The left wheel should lock completely when the brake is set. -
Page 16: Belt Maintenance
Belt Maintenance 6. Lay a straightedge across clutch and flywheel pulleys, tighten belt tension bolt so there is 1 cm (0.40 inch) of flex in the belt when pushing down with 6.8 kg (15 lb) Adjusting the Drive Belt force, at mid-span (when re-tensioning a belt in use) or with 8 kg (18 lb) force when installing a new belt Tension (Figure 19). -
Page 17: Grinder Maintenance
Grinder Maintenance Cleaning Replacing the Teeth Removing Debris from the Machine Service Interval: Before each use or daily—Check the condition of the teeth and rotate or Regular cleaning and washing will increase the life span of replace any that are worn or damaged. the machine. -
Page 18: Storage
Storage 18. Store the unit in a clean, dry garage or storage area. 19. Cover the unit to protect it and keep it clean. For storage over 30 days, prepare the machine as follows: 1. Remove dirt and grime from the external parts of the entire unit, especially the engine. -
Page 19: Troubleshooting
Troubleshooting Problem Possible Cause Corrective Action The engine will not start. 1. The safety bale is in the Off position. 1. Hold the safety bail against the handle. 2. If your model is equipped with an 2. Move the switch to the On position. engine with an On/Off switch, the switch is in the Off position. - Page 20 Toro importer. If all other remedies fail, you may contact us at Toro Warranty Company. Australian Consumer Law: Australian customers will find details relating to the Australian Consumer Law either inside the box or at your local Toro Dealer.