Sharp AR-FX7 Service Manual page 59

SW31 No.3–No.8 Time specification print (min) on the
communication report table
Used to set "min" of the time (o'clock, min) when specifying the time on
the communication report table.
Setup is in the range of 0 – 59 (min) by binary input.
(When set to 60 – 63, the time is set to 0min.)
Default: 0 min
SW32 No.1, No.2 Default telephone book setup
Used to set YES/NO of default telephone book displaying.
Default: 0 0 (Basic screen)
SW32 No. 3 Next address key input in broadcast
Used to set YES/NO of Next address key input in broadcast.
Default: 0 (No)
SW32 No.4, No.5 One-touch dial display number switch
Used to set the number of one-touch dial display.
Default: 0 1 (8)
SW32 No. 6 Shift of the power OFF state in shut off
Used to set whether the shift of the power OFF state in shut off is
allowed or inhibited.
Default: 1 (allowed)
SW32 No. 7 Time indication format
Used to set the sequence of year, month, and day in the LCD display,
report, and sender record.
When set to 1, time is indicated in AM/PM format.
When set to 0, time is indicated in 24H format.
Default: 0 (24H)
SW32 No. 8 Priority in the day of week
Used to set the recording sequence of the day of month and the day of
week if the date is in the sequence of month, day, and year.
Default: 0 (No) (U.K.) 1 (Yes) (Germany, France)
SW33 No. 1 Inhibited to use.
SW33 No. 2 Report output on less than A4 (LTR)
Used to set the report output on less than A4 (LTR).
Default: 0 (Reduction by the record volume)
SW33 No. 3 Own FAX No. mark of TX image
Used to set own number's mark in TX image header. (English only)
When set to 1, mark is TEL icon (
When set to 0, mark is "FAX:".
Default: 0 (FAX:)
SW33 No.4, No.5 Contents of send document are printed
in memory send
Used to set Print/Not print part of the sent document in the transmis-
sion result table in case of a memory transmission error.
When set to 0 0, the transmitted document is not printed on the trans-
mission result table.
When set to 0 1, all the transmitted document are printed on the trans-
mission result table.
When set to 1 0, the transmitted document is printed on the transmis-
sion result table only when the transmission is failed.
Default: 1 0 (when the transmission is failed)
SW33 No. 6 Transmission document content print in F
code transmission
Used to set whether the sent document content is print or not in F code
transmission.
SW33-4 – 5 must be set to output.
Default: 1 (Not print)
).
AR-FX7 SOFT SWITCH 7 - 32
SW33 No. 7 Function to attach images to the report table
of memory confidential send
Used to set whether images are attached to the report table of memory
confidential send
Default: 0 (NO)
SW33 No. 8 Total communication time and total number of
pages print on communication record table
Used to set Print/Not print the total communication time and the total
number of pages on the communication record table.
When set to 1, the total communication time and the total number of
pages are printed on the communication record table.
When set to 0, not printed on the communication record table.
Default: 1 (YES)
SW34 No.1, No.2 Report output (in reception)
Used to set whether the communication report table is outputted or not
when a reception (excluding confidential reception) is made.
Setup is selected from "print inhibition," "all output," and "only when
transmission is failed" as follows:
bit 1 2
0 0 : Print is inhibited.
0 1 : Print all
1 0 : Only in case of an error
Default: 0 0 (printing is inhibited)
SW34 No.3, No.4 Report output (in transmission)
Used to set whether the communication report table is outputted or not
after the transmission (excluding broadcast, sequential send request,
and relay broadcast).
Setup is selected from "print inhibition," "all output," and "only when
transmission is failed" as follows:
bit 3 4
0 0 : Print is inhibited.
0 1 : Print all
1 0 : Only when transmission is failed
Default: 1 0 (Only when transmission is failed)
SW34 No. 5 Communication report output (in confidential
reception)
Used to set whether the communication report table is outputted or not
when a confidential reception is made.
When set to 1, the communication report table is printed.
When set to 0, the communication report table is not printed.
Default: 1 (Print)
SW34 No.6, No.7 Report output (In broadcast, sequential
send request, and relay broadcast)
Used to set whether the communication report table is outputted or not
after the transmission (in broadcast, sequential send request, and
relay broadcast).
Setup is selected from "print inhibition," "all output," and "only the
address to which transmission is failed" as follows:
bit 6 7
0 0 : Print is inhibited.
0 1 : Print all
1 0 : Only the address to which transmission is failed
Default: 0 1 (All print)
SW34 No. 8 Report output when canceling
Used to set whether the communication report table is outputted or not
when canceling transmission during document transmission.
When set to 1, the communication report table is printed.
When set to 0, the communication report table is not printed.
Default: 0 (No print)