Sealey AK2948 Quick Start Manual

thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instruction protection
manual
1. saFetY
Warning! ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this
‰
equipment, make sure you know where the nearest fire extinguisher is.
‰ Warning! Always wear approved eye / face protection when operating the torch.
‰
‰
‰ ‰ Warning! Do not use the torch if you notice damage to the workpiece or if there could be a gas leak from it.
‰
‰
‰ Warning! Butane gas is extremely flammable, handle with care.
‰
‰
Warning! Always point the torch away from the eyes and body when igniting and during operation.
‰
‰ ‰ Warning! Do not put the torch down when it is lit, Do not leave it unattended.
‰
‰
‰ ‰ Warning! The flame is not easily visible in bright daylight.
‰
‰
‰ Warning! ensure the flame is completely extinguished after use. Do not use water to cool the torch down.
‰
‰
Warning! only use in a well ventilated area.
‰
Do not use the torch in an area where paint fumes, solvents or other flammable solids, liquids or gases pose a potential hazard. Keep
8
flammable material away from the torch when operating.
Do not operate the torch when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
Do not hold any workpiece by hand.
8
‰ Do not touch the workpiece close to the heated area as it will be very hot. Allow to cool.
‰ 8
Do not operate the torch if it is damaged as this may cause failure and/or possible personal injury.
8
Do not touch the top of the torch during or immediately after use, as it will be very hot. Allow to cool.
8
Do not allow children to operate the torch.
8
After use, apply the safety lock and allow the torch to cool before storing it.
9
When not in use, store away from direct sunlight in a safe, dry, childproof location.
9
Do not store at over 40°C, such as in a car in hot weather.
8
2. introDuction
Portable and lightweight, suitable for heating, soldering and shrinking. Unit has 3-in-1 system consisting of soldering iron, butane torch and
a flameless heat source. Features adjustable heating control ranging up to 1300°C, and is fitted with a retractable stand. Powered by Butane
(lighter fuel), requires separate ignition.
3. operation
3.1. to Fill. (refer to fig.1)
3.1.1. Use standard butane fuel. Fill in a well ventilated area away from
open flame. Turn the torch off, make sure the flame is out, allow to
cool down for five minutes before filling.
3.1.2. Hold torch upside down and insert the filling can's nozzle into the
gas filling valve. Press nozzle into the valve and release gas.
3.1.3. once gas begins to seep out around the edge of the nozzle, the
gas tank is full. Remove the filling can.
3.2. to use. (refer to fig.1)
3.2.1. Select required flame size using control.
3.2.2. soldering iron. ensure soldering tip is fitted, push to gas on position,
slide shroud up and light through aperture.
3.2.3. butane torch. Remove shroud, push to gas on position and light.
3.2.4. heat source. Remove soldering tip, push to gas on position,
light, slide shroud to vary heat applied.
.
© Jack Sealey limited
butane solDering/heating torch 3-in-1
aK2948
model no:
Original Language Version
Aperture
Gas adjustment lever
AK2948| Issue:2 (H,F) 30/04/18
fig.1