Mitsubishi Electric 800 Series Instruction Manual page 58

Setting
Pr. Name
range
Digital trigger operation
1047 0, 1
selection
1048 Display-off waiting time 0 to 60min
1049 USB host reset 0, 1
1106 Torque monitor filter 0 to 5s, 9999
Running speed monitor
1107 0 to 5s, 9999
filter
Excitation current
1108 0 to 5s, 9999
monitor filter
Station number in
1124 inverter-to-inverter link 0 to 5, 9999
Number of inverters in
1125 inverter-to-inverter link 2 to 6
system
Pre-charge change 0 to 100%,
1132
increment amount 9999
Second pre-charge 0 to 100%,
1133
change increment amount 9999
Second PID display
1136 0 to 500, 9999 9999
bias coefficient
Second PID display
1137 0 to 300%
bias analog value
Second PID display
1138 0 to 500, 9999 9999
gain coefficient
Second PID display
1139 0 to 300%
gain analog value
Second PID set point/
1140 1 to 5
deviation input selection
Second PID measured 1 to 5, 101 to
1141
value input selection 105
1142 Second PID unit selection 0 to 43, 9999
1143 Second PID upper limit 0 to 100%, 9999 9999
1144 Second PID lower limit 0 to 100%, 9999 9999
Second PID deviation 0.0 to 100.0%,
1145
limit 9999
Second PID signal
1146 0 to 7, 10 to 17 0
operation selection
Second output interruption 0 to 3600s,
1147
detection time 9999
Second output interruption
1148 0 to 590Hz
detection level
Second output
1149 interruption cancel level 900 to 1100% 1000%
1150 to
User parameters 1 to 50 0 to 65535
1199
PID gain tuning timeout
1211 1 to 9999s
time
Step manipulated
1212 900 to 1100% 1000%
amount
Step response
1213 0.01 to 600s
sampling cycle
Timeout time after the
1214 1 to 9999s
maximum slope
Limit cycle output upper
1215 900 to 1100% 1100%
limit
Limit cycle output lower
1216 900 to 1100% 1000%
limit
1217 Limit cycle hysteresis 0.1 to 10%
0, 100 to 102,
111, 112, 121,
1218 PID gain tuning setting 122, 200 to
202, 211, 212,
221, 222
PID gain tuning start/ (0), 1, 8, (9,
1219
status 90 to 96)
1300 to
1343,
Communication option parameters
1350 to
1359
Detection time for PID
1361 0 to 900s
output hold
1362 PID output hold range 0 to 50%, 9999 9999
0 to 360s,
1363 PID priming time
9999
Stirring time during
1364 0 to 3600s
sleep
1365 Stirring interval time 0 to 1000h
1366 Sleep boost level 0 to 100%, 9999 9999
Sleep boost waiting
1367 0 to 360s
time
Output interruption
1368 0 to 360s
cancel time
0 to 120Hz,
Check valve closing
1369
completion frequency 9999
Detection time for PID
1370 0 to 900s
limiting operation
PID upper/lower limit
1371 0 to 50%, 9999 9999
pre-warning level range
PID measured value
1372 control set point change 0 to 50%
amount
PID measured value
1373 control set point change 0 to 100%
rate
Auxiliary pressure pump
1374 900 to 1100% 1000%
operation starting level
Initial
Pr. Name
value
Auxiliary pressure pump
0
1375
operation stopping level
0min
Auxiliary motor
1376
stopping level
0
PID input pressure
9999
1377
selection
9999
PID input pressure
1378
warning level
9999
PID input pressure fault
1379
level
9999
PID input pressure
1380 warning set point
2
change amount
PID input pressure fault
1381
operation selection
9999
Starting times lower 4
1410
9999 digits
Starting times upper 4
1411
digits
Motor induced voltage
1412
constant (phi f) exponent
20%
Second motor induced
1413 voltage constant (phi f)
exponent
100% Ethernet communication
1424
network number
2 Ethernet communication
1425
station number
Link speed and duplex
3
1426
mode selection
9999
Ethernet function
1427
selection 1
Ethernet function
1428
selection 2
9999
Ethernet function
1429
selection 3
Ethernet signal loss
1431 detection function
1s
selection
Ethernet communication
1432
0Hz
check time interval
1434 IP address 1 (Ethernet) 0 to 255
1435 IP address 2 (Ethernet) 0 to 255
1436 IP address 3 (Ethernet) 0 to 255
0
1437 IP address 4 (Ethernet) 0 to 255
100s 1438 Subnet mask 1
1439 Subnet mask 2
1440 Subnet mask 3
1441 Subnet mask 4
1s
IP filter address 1
1442
(Ethernet)
10s
IP filter address 2
1443
(Ethernet)
IP filter address 3
1444
(Ethernet)
IP filter address 4
1445
(Ethernet)
1%
IP filter address 2 range
1446
specification (Ethernet)
0
IP filter address 3 range
1447
specification (Ethernet)
IP filter address 4 range
1448
specification (Ethernet)
0
Ethernet command source
1449
selection IP address 1
Ethernet command source
1450
selection IP address 2
Ethernet command source
1451
5s
selection IP address 3
Ethernet command source
1452
selection IP address 4
9999
Ethernet command source
1453 selection IP address 3
range specification
15s
Ethernet command source
0h
1454 selection IP address 4
range specification
1455 Keepalive time
0s
1460 PID multistage set point 1
1461 PID multistage set point 2
0s
1462 PID multistage set point 3
9999 1463 PID multistage set point 4
1464 PID multistage set point 5
0s
1465 PID multistage set point 6
1466 PID multistage set point 7
Number of cleaning
1469
times monitor
5%
Number of cleaning
1470
times setting
1471 Cleaning trigger selection 0 to 15
0%
Cleaning reverse
1472
rotation frequency
Cleaning reverse
1473 rotation operation time 0 to 3600s
Setting Initial
Pr.
range value
Cleaning forward
1474
900 to 1100% 1000%
rotation frequency
Cleaning forward
0 to 100%,
1475
9999
rotation operation time
9999
1476 Cleaning stop time
1 to 3, 9999 9999
Cleaning acceleration
1477
time
0 to 100% 20%
Cleaning deceleration
1478
time
0 to 100%,
9999
1479 Cleaning time trigger
9999
Load characteristics
1480
0 to 100% 5%
measurement mode
Load characteristics
1481
0, 1 0 load reference 1
Load characteristics
1482
load reference 2
0 to 9999 0
Load characteristics
1483
load reference 3
0 to 9999 0
Load characteristics
1484
0 to 2, 9999 9999 load reference 4
Load characteristics
1485
load reference 5
0 to 2, 9999 9999
Load characteristics
1486
maximum frequency
1 to 239 1
Load characteristics
1487
minimum frequency
1 to 120 1
Upper limit warning
1488
detection width
0 to 4 0
Lower limit warning
1489
detection width
502, 5000 to
5001
Upper limit fault
1490
5002, 5006 to
detection width
5008, 5010 to
45237
Lower limit fault
5013, 9999,
1491
detection width
45237, 47808,
9999
61450
Load status detection
signal delay time / load
1492
reference measurement
0 to 3 0
waiting time
1499 Parameter for manufacturer setting. Do not set.
0 to 999.8s,
9999
Pr.CLR Parameter clear
9999
ALL.CL All parameter clear
192
Err.CL Fault history clear
168
Pr.CPY Parameter copy
50
Pr.CHG Initial value change list ―
1
IPM IPM initialization
0 to 255 255
AUTO Automatic parameter
0 to 255 255
setting
0 to 255 255
Pr.Md Group parameter setting (0), 1, 2
0 to 255 0

Differs according to capacities.
0 to 255 0
• 6%: FR-F820-00046(0.75K) and FR-F840-
00023(0.75K)
• 4%: FR-F820-00077(1.5K) to 00167(3.7K) and FR-
0 to 255 0
F840-00038(1.5K) to 00083(3.7K)
• 3%: FR-F820-00250(5.5K), 00340(7.5K), FR-F840-
0 to 255 0
00126(5.5K) and 00170(7.5K)
• 2%: FR-F820-00490(11K) to 01540(37K) and FR-
0 to 255 0 F840-00250(11K) to 00770(37K)
• 1.5%: FR-F820-01870(45K), 02330(55K), FR-F840-
00930(45K) and 01160(55K)
0 to 255, 9999 9999
• 1%: FR-F820-03160(75K) or higher and FR-F840-
01800(75K) or higher
0 to 255, 9999 9999 
For FR-F820-02330(55K) or lower and FR-F840-
01160(55K) or lower

For FR-F820-03160(75K) or higher and FR-F840-
0 to 255, 9999 9999
01800(75K) or higher

For FR-F820-00340(7.5K) or lower and FR-F840-
0 to 255 0
00170(7.5K) or lower

For FR-F820-00490(11K) or higher and FR-F840-
00250(11K) or higher
0 to 255 0

Differs according to capacities.
• 4%: FR-F820-00340(7.5K) or lower and FR-F840-
0 to 255 0
00170(7.5K) or lower
• 2%: FR-F820-00490(11K) to 02330(55K) and FR-
F840-00250(11K) to 01160(55K)
0 to 255 0
• 1%: FR-F820-03160(75K) or higher and FR-F840-
01800(75K) or higher

0 to 255, 9999 9999 Differs according to the voltage class. (200 V class/400
V class)

The parameter number in parentheses is the one for
use with the LCD operation panel and parameter unit.
0 to 255, 9999 9999

Differs according to types. (FM type/CA type)

The setting is available only with the CA type.
1 to 7200s 3600s 
The setting value "60" is only available for Pr.178, and
"61" is only for Pr.179.
9999

The setting values "92, 93, 192, 193" are only available
9999
for Pr.190 to Pr.194.

Simple mode parameters. (When Pr.160 = "9999", only
9999
the simple mode parameters are displayed.)
0 to 100%,
9999

The setting is available when the PLC function is
9999
enabled.
9999
9999
9999
0 to 255 0
0 to 255 0
0
0 to 590Hz 30Hz
5s
Setting Initial
Name
range value
0 to 590Hz,
9999
9999
0 to 3600s,
9999
9999
0 to 3600s 5s
0 to 3600s,
9999
9999
0 to 3600s,
9999
9999
0 to 6000hr 0
0, 1, (2, 3, 4, 5,
81, 82, 83, 84, 0
85)
0 to 400%,
9999
8888, 9999
0 to 400%,
9999
8888, 9999
0 to 400%,
9999
8888, 9999
0 to 400%,
9999
8888, 9999
0 to 400%,
9999
8888, 9999
0 to 590Hz 60/50Hz

0 to 590Hz 6Hz
0 to 400%,
20%
9999
0 to 400%,
20%
9999
0 to 400%,
9999
9999
0 to 400%,
9999
9999
0 to 60s 1s
(0), 1 0
(0), 1 0
(0), 1 0
(0), 1 to 3 0
―
0, 12 0
― ―
0
17
Parameter list