Toro Reelmaster 7000-D Operator's Manual
27-inch heavy-duty verticutter dpa cutting unit
Hide thumbs
Also See for Reelmaster 7000-D:
- Service manual (468 pages) ,
- Operator's manual (144 pages) ,
- Installation instructions (2 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Toro Reelmaster 7000-D
Summary of Contents for Toro Reelmaster 7000-D
- Page 1 Form No. 3366-458 Rev A 27-inch Heavy-Duty Verticutter Reelmaster ® 7000-D DPA Cutting Unit Model No. 03716—Serial No. 311000001 and Up To register your product or download an Operator's Manual or Parts Catalog at no charge, go to www.Toro.com. Original Instructions (EN)
-
Page 2: Table Of Contents
Removing the Verticutter Blades from the additional information, contact an Authorized Service Shaft .............. 10 Dealer or Toro Customer Service and have the model Install Verticutter Blades........10 and serial numbers of your product ready. Write the Servicing the Roller ..........10 numbers in the space provided. -
Page 3: Safety
Toro replacement parts and repair or replace it before operation is commenced. accessories to keep the Toro all TORO. Never use Also tighten any loose nuts, bolts, and screws to "will-fit" replacement parts and accessories ensure verticutter is in safe operating condition. -
Page 4: Setup
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. Verticutter Inspect the verticutter Transport roller assembly Install the transport rollers. Cotter pin – No parts required Adjust the blade depth. – No parts required Adjust the rear grass shield. -
Page 5: Inspecting The Verticutter
Note: Determine the left and right sides of the machine from the normal operating position. Note: Whenever the verticutter has to be tipped to expose the verticutter blades, use the kick stand Installing the Transport Rollers (supplied with traction unit) (Figure 2). Parts needed for this procedure: Transport roller assembly Cotter pin... -
Page 6: Adjusting The Rear Grass Shield
Figure 5 G012693 1. Rear grass shield 2. Pivot bolt Figure 4 2. Adjusting bolt 1. Gauge bar 2. Rotate the grass shield to the desired setting, and tighten the bolts (Figure 5). Note: The verticutter blades must not touch the CAUTION gauge bars. -
Page 7: Adjusting The Transport Rollers
2. Move the scraper rods in or out to attain 0.0 to 0.03 The verticutters can be installed at any of the five inch (0.0 to 0.75 mm) clearance between the scraper locations on the traction unit. Figure 7 shows the and roller. -
Page 8: Product Overview
Product Overview Operation Note: Determine the left and right sides of the Specifications machine from the normal operating position. Net Weight 158 lb. (72 kg) Training Period Before operating the verticutter reels, evaluate the performance of the reel at the desired setting. Operate in a clear, unused area to determine if the desired results will be achieved. -
Page 9: Maintenance
Maintenance Lubricating the Verticutter Each verticutter has 6 grease fittings (Figure 8) that must be lubricated weekly with No. 2 General Purpose Lithium Base Grease. The lubrication points are the front roller (2), the rear roller (2) and the reel bearings (2). Important: Lubricating cutting units immediately G012694 after washing helps purge water out of bearings and... -
Page 10: Removing The Verticutter Blades From The Shaft
Removing the Verticutter Install Verticutter Blades Blades from the Shaft 1. Assemble a reel blade (Figure 12). 2. Assemble a large spacer. 1. Secure the end of the verticutter shaft, which has only one washer and nut, in a vise. 3. - Page 11 Figure 13 1. Rebuild kit (Part No. 114–5430) 6. Bearing nut 2. Rebuild tool kit (Part No. 115–0803) 7. Inner seal tool 3. Inner seal 8. Washer 4. Bearing 9. Bearing/outer seal tool 5. Outer seal...
- Page 12 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor’s service or have difficulty obtaining guarantee information, contact the Toro importer.