GE L90 Instruction Manual page 895

INDEX
Real-time clock
actual values for synchronization .............................................. 6-9
settings ...............................................................................................5-108
Reboot relay
using EnerVista .................................................................................... 5-1
using relay .............................................................................................. 7-3
Recloser curves
................................................................... 5-163, 5-261
Reclosing
logic diagrams ................................................................................5-407
sequence diagram ........................................................................5-411
settings ...............................................................................................5-399
Redundancy
PRP actual values .............................................................................6-11
PRP explained .....................................................................................5-48
settings ..................................................................................................5-46
specifications ......................................................................................2-48
Relay architecture
............................................................................5-187
Relay maintenance
............................................................................... 7-3
Relay name
..........................................................................................5-135
Release Notes .....................................................................................11-14
Remote access of front panel in EnerVista
Remote access, explained
Remote loopback settings
Remote Setting Authorization
Remote terminal FlexAnalogs
Repair
...................................................................................1-2, 11-29, D-1
Replace battery .................................................................................11-24
Replace battery message
................................................................. 7-9
Replace front panel
.........................................................................11-15
Replacement modules
......................................................................2-26
Requirements for installation
Reset to factory defaults
....................................................... 5-9, 5-23
Resetting
FlexLogic operands .......................................................................5-202
setting to clear LEDs and messages ....................................5-421
to factory defaults .............................................................................. 5-9
Restart relay
using EnerVista .................................................................................... 5-1
using relay .............................................................................................. 7-3
Restore settings
....................................................................................11-8
Restraint current FlexAnalogs
Restricted ground fault
actual values .......................................................................................6-27
FlexAnalogs ........................................................................................... A-1
FlexLogic operands .......................................................................5-198
logic diagram ...................................................................................5-285
settings ...............................................................................................5-282
specifications ......................................................................................2-34
Revision history
.......................................................................................D-1
RF immunity specifications
RFI, conducted specifications
R-GOOSE description
.........................................................................5-66
RJ-45
...............................................................................................2-11, 3-11
RMS voltage specifications
Roles for login
.......................................................................................... 2-9
Rolling demand
..................................................................................5-121
Routable GOOSE
...................................................................................5-66
L90 LINE CURRENT DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL
................. 4-17, 6-3
................................................................ 5-9
...........................................................5-432
...................................................11-14
..................................................... A-16
.......................................................3-51
..................................................... A-16
............................................................2-52
.......................................................2-52
............................................................2-43
RS232
baud rate ............................................................................................. 5-43
configuration ...................................................................................... 3-63
specifications ..................................................................................... 2-48
wiring ..................................................................................................... 3-29
RS422
configuration ...................................................................................... 3-39
timing ..................................................................................................... 3-41
two-channel application .............................................................. 3-39
with fiber interface .......................................................................... 3-42
RS485
description ........................................................................................... 3-31
port on rear panel ............................................................................ 3-11
settings ................................................................................................. 5-43
specifications ..................................................................................... 2-48
RTD FlexAnalogs
.................................................................................. A-27
RTD inputs
actual values ...................................................................................... 6-27
settings ...............................................................................................5-423
specifications ..................................................................................... 2-45
Rules for passwords
.............................................................................5-9
RxGOOSE
actual values ...................................................................................... 6-25
error messages ................................................................................. 7-11
FlexAnalogs ......................................................................................... A-29
settings ................................................................................................. 5-71
S
Save settings
............................................................................................4-1
Saving setting does not take relay out of service
SCADA protocol selection
............................................................... 5-52
SCD file
import ..................................................................................................11-12
import preferences .......................................................................... 11-9
SCL compatible
.................................................................................... 5-58
SCL file import
............................................................... 5-75, 5-77, 5-78
preferences ......................................................................................... 11-9
Security
commands .............................................................................................7-6
delete files and records ...............................................................11-29
EnerVista and UR secure with SSH .............................................2-8
failed authentication lockout ..................................................... 5-23
forceful user logout ............................................................................7-3
lock FlexLogic equations .................................................................4-9
password for settings template ...................................................4-7
passwords for settings and commands ................... 4-61, 5-11
RADIUS server for user authentication .....................................B-1
role-based user access ....................................................................2-9
settings ................................................................................................. 5-21
software options .............................................................................. 2-50
specifications ..................................................................................... 2-50
system and event logs ................................................................... 5-26
Security audit list of port numbers
...............5-1
........................................... 5-46
xiii